Taylor ESPRESSO Toy Storage Chest Bedienungsanleitung

Quality Wooden Children’s Furniture and Accessories

• Please inspect the parts for damage during shipping and for any missing items. If you suspect that there may be damage or a shortage, contact us

and we will send replacement parts if needed.

• As soon as components and hardware are unpacked; please remove and recycle all plastic bags from possible contact with children.

• Words in Red represent a component or hardware used in assembly.

• Illustrations are intended to help identify components and hardware and are not drawn to scale.

Please read instructions carefully to

avoid accidental damage to

components during assembly.

Hardware

4- #8 5/8 in.

Wood Screws

12- Joint Connector Bolts

14- #5 5/8 in.

Wood Screws

1- Lid Support

Toy Storage Chest Components

Page 1 of 3

Tools needed for assembly

• Medium size #2 Phillips

Screwdriver

• Supplied Allen Wrench

Front

Back

Side

Bottom

WARNING: ADULT ASSEMBLY REQUIRED

WARNING: Assembly kit contains parts with sharp points.

WARNING: Assembly kit contains parts with sharp edges.

WARNING: Package contains plastic bags that present suffocation risks for children.

WARNING: Assembly kit contains small parts that present choking hazards for children.

12- Barrel

Top

Bottom

Lid

Made in America

Toy Storage Chest Assembly Instructions; ESPRESSO

Quality Wooden Children’s Furniture and Accessories

Toy Stoprage Chest Assembly Instructions- Continued

• Insert a Barrel Nut into the Back panel

Barrel Nut hole in relation to the Joint

Connector Bolt previously installed.

• Make sure the longest slot on the head

of the Barrel Nut is perpendicular to

the Joint Connector Bolt.

• Fasten the Side panel and Back panel

together. Start Joint Connector Bolt by hand

and after a few turns begin using the supplied

Allen wrench.

• Make sure Back panel ts inside groove.

Tighten bolt to a snug t. Then unscrew one

full turn to allow adjustment.

• Now, repeat steps 1,2 and 3 for

second hole and to assemble

the other Side panel.

• Starting with a Side panel, insert one Joint

Connector Bolt in Joint Connector Bolt

hole.

• Repeat steps 1, 2 and 3 to attach

Front panel to body.

• With the box sitting at on a hard

surface, tighten all eight bolts.

Bottom Panel

Panel Groove

12 3

456

Page 2 of 3

• Using the existing holes, attach bottom of

Lid Support to inside of Back with 2 #8 screws

• Be careful not to over tighten screws.

• Place Lid on top of the box and line

up existing holes located on outside

of the back panel to holes in hinge.

Attach hinge to back of box using 14

#5 screws.

• Be careful not to over tighten screws.

Lid

Body

Back

Lid Support

Partial view of Back/Front panel

Barrel Nut Holes

Joint Connector

Holes

Side Panel

Top

Bottom

Area of Detail

Made in America

• Now that you have the two sides

fastened to the back; slide the

Bottom panel in the bottom grooves

(The side with the logo is the top

side).

• Open lid to approximately 85 degrees and hold it

in place. Mount the top part of the Lid Support to

the inside of the lid using 2 #8 screws.

• It is very important that the screws be started in

the indentations or the lid support may not function

properly

•Be careful not to over tighten screws.

Toy Storage Chest Assembly Instructions- Continued

Please Recycle Instructions

• Now that you have completed the assembly,

open and close the lid 10 times to break in the

lid support mechanism.

•The lid should not fall when the Lid Support is

properly installed.

• If the lid does not stay in position when raised,

please call us and we will help you. Until the lid

support is properly installed, do not allow

children to use this product. Please check the

lid support mounting screws periodically to

make sure they remain tight.

Page 3 of 3

Use and Care Instructions

WARNING

Failure to properly install Lid Support

will result in an entrapment hazard.

Lid

Body

Made in America

Quality Wooden Children’s Furniture and Accessories

Please check out to see our other products that are all made here in America. The safety of your children is our highest concern. We are a GREEN company and

hope you will be able to recycle the packaging mate-rial that we used to ship your product.

Use and care instructions:

The nish on this product is an environmentally friendly water base acrylic made by Sherwin Williams. It may be cleaned with a furniture polish, lemon oil or a non