TDK SESUB-PAN-T2541 EVK Bedienungsanleitung

SESUB-PAN-T2541 EVK

Bluetooth® Low Energy Module Quick Start Guide

Kit Contains:

1. SP13808: SESUB-PAN-T2541 Evaluation Module

- Equipped with the SESUB-PAN-T2541 BLE Module, a 2.4GHz band

chip antenna, and a 32.768kHz sleep clock resonator

2. SP13809: Adapter Board

- The adapter board contains switches and LEDs used during the TI BLE

Multitool demonstration, and also a pin header for TI’s CC-Debugger.

3. Battery Pack Power Supply

4. Product Selection Guide









1. Download the Texas Instruments ‘TI BLE Multitool’ App from the App Store for your

Bluetooth® 4.0 compatible iOS device*. The TI BLE Multitool Icon will appear on your

home screen when installed properly.

*Bluetooth® 4.0 is compatible with iPhone 4s and iPad 3

Gen. or later models

2. Connect the battery pack* to the SESUB-PAN-T2541 evaluation module/adapter

board. The red cable connects to the top pin (Vcc), and the black cable connects to

the bottom pin (GND), as shown below.

*3.0-3.6 V is the recommended power supply voltage

Red Cable

Black Cable

App Store Icon TI BLE Multitool

App Icon

3. Make sure the Bluetooth function is set to ‘On’ on your iOS device, and then open the

TI BLE Multitool App.

4. Make the evaluation module discoverable by pressing the SW1 button. LED1 will

begin to flash on the evaluation board, and ‘TDK BLE Smart Tag’ will appear under

Available Devices in the TI BLE Multitool App.

TI BLE Multitool

App Icon

SW1 LED1

6. Push SW1 or SW2 to see the respective buttons on the screen of your iOS device

change position.

5. Select ‘TDK BLE Smart Tag’ from the main screen of the TI BLE Multitool App.

Notice the two buttons near the top of the screen, the device information in the

middle, and the RSSI value near the bottom.

This value will change as the iOS device and

the SESUB-PAN-T2541 evaluation module

are moved closer or further from one another.

As the evaluation module is moved closer to

the iOS device, the RSSI value becomes

larger, and as the evaluation module is moved

further from the iOS device, the RSSI value

becomes smaller.

SW1 SW2

SW1 is pressed SW2 is pressed

Usin

the SESUB-PAN-T2541 EVK with the TI CC-Debu

Needed:

SESUB-PAN-T2541 EVK

TI CC-Debugger

oThe CC-Debugger must be purchased separately.

PC (Windows OS)

SmartRF Flash Programmer

oTI’s Flash Programmer software “swrc044s.zip” (V1.12.7 5/6/2013) is included

within the firmware folder on the TDK Products Selection Guide USB drive

oThe latest version of this software can also be downloaded through TI’s

website by searching “SmartRF Flash Programmer”. – www.ti.com

1. Download and install the SmartRF Flash Programmer from the TI website or from the

“swrc044s.zip” file on the TDK Products Selection Guide USB drive. Search

“SmartRF Flash Programmer” on www.ti.com and click “Get Software” to download

the swrc044s.zip file.

2. Connect the CC-Debugger to the SESUB evaluation module. Make sure to connect

the ribbon cable in the appropriate direction. If the cable is connected incorrectly, the

hardware may be damaged.

2. Save the swrc044s.zip file to your PC. Open the zip file from the location where it was

saved and run the .exe executable file to install the TI SmartRF Flash Programmer.

3. Follow the automatic prompts to install the software.

4. Launch the SmartRF Flash Programmer software by clicking the icon below on your

desktop.

5. Connect the SESUB-PAN-T2541 EVK to the CC-Debugger, and then connect the

CC-Debugger to the PC using the mini USB cable. When the USB cable is

connected, the PC should automatically prompt you to update the driver as long as

the software from Step 3 has been installed.

Mini USB-USB Cable

6. Make sure the firmware on the CC-Debugger is up to date. To update the firmware on

the CC-Debugger, first remove the SESUB-PAN-T2541 EVK from the CC-Debugger.

Select “Program Evaluation Board” from the ‘What do you want to program?”

dropdown list from within the Smart RF Programmer

Click the “Update EB Firmware” button

Make sure that “Erase, program, and verify” is selected under “Actions”

Click the “Perform actions” button

Note: For additional information or any questions regarding the CC-Debugger, please refer to

the TI CC-Debugger User’s Guide: http://www.ti.com/lit/ug/swru197h/swru197h.pdf.

7. Install the latest version of firmware for the SESUB-PAN-T2541 EVK Module.

Select “Program CCxxxx SoC or MSP430” from the “What do you want to program?”

dropdown

Make sure that the CC-Debugger is highlighted in the System-on-Chip menu

Select the “SP13808_FW_v0r52_STD.hex” file from the firmware folder on the TDK

Products Selection Guide USB drive in the Flash Image section

Make sure “Erase, program and verify” is selected under the Actions menu and click

“Perform Actions”



*Note if firmware fails to update, check the hardware connections and repeat installation.

Andere TDK Adapter Handbücher

TDK

TDK BlueM Bedienungsanleitung

TDK

TDK HHM Series HHM2209SA2 Bedienungsanleitung

TDK

TDK HHM Series HHM2208SB1 Bedienungsanleitung

TDK

TDK HHM Series HHM2241SA1 Bedienungsanleitung

TDK

TDK bluetooth usb adapter Bedienungsanleitung

TDK

TDK R520M Bedienungsanleitung

TDK

TDK HHM Series HHM2209SA1 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

RCA

RCA AH57R Bedienungsanleitung