TDK TVT1001BLK Bedienungsanleitung

PROFESSIONAL TURNTABLE WITH AUTO SPEED CORRECTION

Belt-Drive Turntable

USER GUIDE

TVT1001BLK

TVT2002BLK Imation Confidential - Use Only By Permission

Controlled material extracted from Matrix on Aug 24, 2010 08:31:11 AM CDT

SAFETY PRECAUTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DANGEROUS VOLTAGE:

The lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user

to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

ATTENTION:

The exclamation point within an equilateral triangle is intended to alert the user to the presence

of important operating and maintenance (servicing) instructions in the literature accompanying

the appliance.

FCC WARNING:

This equipment may generate or use radio frequency energy. Changes or modications to this equipment

may cause harmful interference unless the modications are expressly approved in the instruction manual. The

user could lose the authority to operate this equipment if an unauthorized change or modication is made.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS

LA BORNE CORRESPONDANTE DE LA PRISES ET POUSSER JUSQU’AU FOND.

Imation Confidential - Use Only By Permission

Controlled material extracted from Matrix on Aug 24, 2010 08:31:11 AM CDT

4 5

SAFETY PRECAUTIONS

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

•Reorientorrelocatethereceivingantenna.

•Increasetheseparationbetweentheequipmentandreceiver.

•Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.

•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

•Theratinginformationislocatedatthebottomoftheapparatus.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Microsoft,XP,andVistaareeitherregisteredtrademarksortrademarksofMicrosoftCorporationintheUnitedStatesand/orothercountries.

Mac is either a registered trademark or trademark of Apple.

This product is not endorsed or manufactured by Microsoft Corporation or Apple.

SURGE PROTECTORS: It is recommended to use a surge protector for AC connection. Lightning and power surges

ARE NOT covered under warranty for this product.

Onlyuseattachments/accessoriesspecifiedbythemanufacturer.

Tobecompletelydisconnectedfromthepowerinput, themainplugoftheAC/DCadaptershallbedisconnectedfromthe

electricaloutlet.ThemainplugoftheAC/DCadaptershouldnotbeobstructedORshouldbeeasilyaccessedduringintended

use. Do not expose the product to dripping or splashing. Do not place liquid filled objects such as vases on the product.

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider

than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are

provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Onlyuseattachments/accessoriesspecifiedbythemanufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus.Whenacartisused,usecautionwhenmovingthecart/apparatuscombinationtoavoidinjury

from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been

dropped.

15. Do not expose this product to dripping or splashing. Do not place objects filled with liquids, such as vases, on this product.

16. Main plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect

the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely.

17. CAUTION: To reduce the risk of fire or explosion, do not expose batteries to excessive heat such as sunshine,

fire or other heat sources.

IMPORTANT SAFETY INSTRUCTIONS

Imation Confidential - Use Only By Permission

Controlled material extracted from Matrix on Aug 24, 2010 08:31:11 AM CDT

6 7

WHAT’S INCLUDED

Platter Cover

Part No. 507-E13000-00R*

*Consumer Replaceable Part (See page 34 to order.)

AC Adapter

Part No. 001-41E130-01R* Main Unit

Platter with Belt

Platter Part No. 434-E13000-00R*

Belt Part No. 447-E13000-00R*

WHAT’S INCLUDED (CONTINUED)

Belt Cover

Part No. 447-E13000-00R*

Included but not pictured: Owner’s Manual and Quick Start Guide

*Consumer Replaceable Part (See page 34 to order.)

B Type USB Cable

(TVT2002 only)

Part No. 061-100100-04RP*

Audio Cable

Part No. 008-000015-10P* 45 Adapter

Part No. 456-E13000-00R* Counter Weight

Part No. (A) 449-E13000-00R*

(B) 278-E130N00-001R*

Dust Cover

Part No. 301-E13000-00R*

CD ROM

(TVT2002 only)

Part No. 393-E13000-000R*

Imation Confidential - Use Only By Permission

Controlled material extracted from Matrix on Aug 24, 2010 08:31:11 AM CDT

8 9

1. Motor/MotorCover

2. Drive Belt

3. Spindle

4. Tone Arm Lifter

5. Counter Weight

6. Anti-Skate Control

7. Cue Lever

8. Tone Arm Rest

9. 33/OFF/45Controlwith

Power Indicator

10. Platter

11. Tone Arm Light

12. Stylus (Stylus Part No.

069-MG2801-01R*)

13. Display

14. Tone Arm

15. Audio Out Jacks

16. PRE-AMPON/OFFSwitch

(Please see caution on use

of this switch on page 12.)

17. B Type USB Out Jack

(TVT2002 only)

18. Power Jack

*Consumer Replaceable Part

(See page 34 to order.)

LOCATION OF CONTROLS

10 11 12 13 14

2 3 5 64 7 8

15 16 17 18

TOP

REAR

SETUP

After unpacking, set up the unit as follows:

1. Gently place the Platter onto the Spindle,

making certain that the Platter is fully seated

before proceeding to the next step.

2. Place the Platter Cover onto the Platter.

3a. Remove the plastic

cover from the stylus.

3b. Gently pull the Drive Belt around the Motor

Pulley. Be careful to not allow finger grease or

other contamination to foul the belt.

NOTE:

The Drive Belt comes installed around the Platter.

4. Place the Motor Cover onto the Motor,

making sure each side has the Drive Belt

coming through.

Imation Confidential - Use Only By Permission

Controlled material extracted from Matrix on Aug 24, 2010 08:31:11 AM CDT

10 11

5. Installation of the Counterweight

As with all quality turntables built to utilize

aftermarket cartridges, the weight of

the cartridge must be balanced with a

counterweight to allow accurate setting of the

cartridge’s downward force.

5a. The first step is to insure a level, stable surface for

your new turntable.

5b. While carefully securing the tonearm from

movement and protecting the stylus from

damage; gently glide the counterweight with

the numerals facing forward onto the rear of the

tonearm.

5c. Rotate the weight in a clockwise fashion from

the perspective of the end of the arm opposite

of the cartridge until the threads are just

engaged.

5d. With the tonearm lift lowered and the stylus

protector removed, seek to instill a state

of equilibrium in the arm by rotating the

counterweight so that balance will be achieved

in the form of a tonearm that is level and free

from interference.

5e. The next step is to create a reference to this

position by rotating the numerically enhanced

ring at the front of the counterweight to indicate

“0” at the top position in alignment with the

mark on the tonearm while holding the rear

portion of the counterweight to prohibit its

movement.

5f. From this “0” reference place, grasp both

the front and back of these two parts of the

counterweight and set the weight to indicate

“3” on the dial to align with the marking on the

top of the tonearm. This will indicate 3 grams of

downward force, the recommended tracking

weight for this cartridge.

5g. Finally, set the antiskating control to “3” to

match the downward force setting. See page

16 in the Operation section for possible further

adjustments.

NOTE:

Other cartridges will have other requirements;

therefore see the cartridge manufacturer’s

documentation for settings such as downward

force and anti-skating recommendations.

SETUP (CONTINUED) SETUP (CONTINUED)

A. TO USE WITH A COMPUTER (TVT2002 only):

Install recording software as shown on page 22.

With the unit NOT connected to AC, connect the

small end of the USB Cable (included) to the USB

Out jack on the rear of this unit and the other end

to a USB jack on your computer.

NOTES:

• Whenconnectingtheunit,refertotheowner’s

manual of the computer, as well as this manual.

• Makesurethepowerisoffandbothunitsare

unplugged before making any connections.

• WhenconnectedviatheUSBcable,theUSB

indicator will light in the display.

6a. Insert the small end of the AC adapter into the Power jack

(located on the rear of the unit). Connect the other end

to a wall outlet having 120V AC, 60 Hz.

NOTES:

• RemoveboththeDCplugandtheACINplugto

disconnect the AC adapter when not in use.

• OnlyusethesuppliedACadapterwhichhasthe

following specs: DC 12V.

CONTINUE TO PAGE 15 TO USE THE TURNTABLE WITH A COMPUTER

TO AC

JACK

Computer

Turntable

USB cable

USB jack

Imation Confidential - Use Only By Permission

Controlled material extracted from Matrix on Aug 24, 2010 08:31:11 AM CDT

12 13

SETUP (CONTINUED)

B. TO USE WITH A UNIT WITH LINE IN JACK (HOME STEREO, BOOM BOX, ETC.):

NOTES:

• Whenconnectingtheunit,refertotheowner’smanual

of the external unit, as well as this manual.

• Makesurethepowerisoffandbothunitsareunplugged

before making any connections.

6b. Connect the left and right plugs of the Audio Cable

(included) to the Left and Right Out jacks on the rear

of this unit, matching the red to red and white to white.

Connect the other end of the Audio Cable to the Line In

jacks of the Home Stereo or similar equipment.

Warning Regarding the PRE-AMP Switch

This unit is equipped with a moving magnet phono

preamplifier with RIAA equalization. This is a very convenient

addition for those customers not possessing an amplifier or receiver with a phono input. However, caution

should be applied to the use of this preamplifier. When you are using this preamplifier’s output as indicated

by the “ON” designation of the switch located on the back center panel of the turntable, do not under any

circumstances connect the RCA output connectors of the turntable to the input connections of an additional

phono preamplifier on a receiver or amplifier often marked “Phono Input”. Excess gain from the use of the

preamplifier in the turntable as well as the preamplifier in your amplifier or receiver may cause damage to

youramplifierand/orspeakers.

OUTPUT

R L

Amplifier

Turntable

On the contrary, if you have this switch in the “OFF” position and attempt to connect the turntable’s RCA

connectors to the line input levels of a receiver or amplifier such as “Tape” or “VCR”, you will find that the

level is insufficient and will not allow you to hear the output sufficiently. Under no circumstances do we

recommendswitchingthepreamplifier“ON/OFF”switchwhilemonitoringtheoutputwithanamplifier.To

be safe, select the appropriate switch position with the power off on the amplifier or receiver. The PRE-AMP

switch position will not affect users of the USB function.

7b. SlidethePRE-AMPON/OFFswitchontherearofthe

unit to the ON position.

8b. Insert the small end of the AC adapter into the Power

jack (located on the rear of the unit). Connect the

other end to a wall outlet having 120V AC, 60 Hz.

NOTES:

• RemoveboththeDCplugandtheACINplugto

disconnect the AC adapter when not in use.

• OnlyusethesuppliedACadapterwhichhasthefollowingspecs:DC12V.

• Afterconnecting,settheexternalunittoreceivethesignalfromitsLineInjacks.

SETUP (CONTINUED)

TO AC

JACK

Imation Confidential - Use Only By Permission

Controlled material extracted from Matrix on Aug 24, 2010 08:31:11 AM CDT

14 15

SETUP (CONTINUED) OPERATION

1. Put a record on the turntable and remember to use the 45

adapter if using a 45 single record.

NOTE: Some 45 single records may not need the 45 adapter.

2. Rotatethe33/OFF/45controltothe33or45position

(to match the record being played); the Power indicator

and display will light.

3. Lift the Tone Arm and move over the Platter. The Platter will

start spinning and the Tone Arm light will illuminate.

4. Lower the Cue Lever.

5. Place the Tone Arm on the edge of the record to start at the

beginning or anywhere on the record’s playing surface to start

playback at that point. The display will show the spectrum of the

record’s output.

6. If the sound is distorted, check the tonearm balance,

counterweight and anti-skating setting previously adjusted.

Also check for accumulated dust on the stylus by visual

inspection.

(See page 10 for Installation of the counterweight.)

C. TO USE WITH A UNIT WITH PHONO PREAMPLIFIER INPUTS (RECEIVER, PRE-AMP, ETC.):

(See page 10 for the Warning regarding the PRE-AMP switch.)

6c. SlidethePRE-AMPON/OFFswitchontherearofthe

unit to the OFF position.

7c. Connect the left and right plugs of the Audio Cable

(included) to the Left and Right Out jacks on the rear

of this unit, matching the red to red and white to white.

Connect the other end of the Audio Cable to the Phono

In jacks of the Home Stereo or similar equipment.

8c. Insert the small end of the AC adapter into the Power jack

(located on the rear of the unit). Connect the other end

to a wall outlet having 120V AC, 60 Hz.

NOTES:

• RemoveboththeDCplugandtheACINplugto

disconnect the AC adapter when not in use.

• OnlyusethesuppliedACadapterwhichhasthe

following specs: DC 12V.

• Afterconnecting,settheexternalunittoreceivethe

signal from its Phono Input jacks.

OUTPUT

R L

Amplifier

Turntable

TO AC

JACK

Imation Confidential - Use Only By Permission

Controlled material extracted from Matrix on Aug 24, 2010 08:31:11 AM CDT

16 17

OPERATION (CONTINUED)

7. If necessary, adjust the Anti-Skating control as previously discussed

in the initial setup. In most cases, the Anti-Skating control should

be set to the same number as the counterweight. Anti-Skating

compensates for inward tracking forces that occur with all

cartridges and typically worsen when the stylus nears the center

of the record. If the turntable is experiencing excessive skipping

during playback while nearing the center spindle, try increasing

the Anti-Skating control in small increments. This control’s

effectiveness is also dependant on tracking force used with the

arm (i.e., the heavier the tracking weight, typically the less anti-

skating is required).

8. To pause playback, raise the Cue Lever; to resume playback,

lower the Cue Lever.

9. When the record reaches the end, the turntable will stop rotating

and the Tone Arm light will turn off. Raise the Cue Lever and move

the Tone Arm back over the Tone Arm rest; then lower the Cue

Lever. To stop playback before the end of the record is reached,

raise the Cue Lever and move the Tone Arm back over the Tone

Arm rest; then lower the Cue Lever.

OPERATION (CONTINUED)

10.Toturntheunitoff,rotatethe33/OFF/45controltotheOFFposition;

the Power indicator and display will turn off. Replace plastic Stylus

cover to protect stylus.

NOTE: If connected to a computer (TVT2002 only), see page 23 to

utilize the included software to record and edit the recording.

Imation Confidential - Use Only By Permission

Controlled material extracted from Matrix on Aug 24, 2010 08:31:11 AM CDT

18 19

OPERATION (CONTINUED)

REPLACING THE TURNTABLE STYLUS (NEEDLE)

Your stylus should last for up to 400 hours. However, when the time comes to replace,

follow the instructions below.

1. Very gently, slide the stylus towards the front and remove

from the assembly.

2. To replace, slide new stylus onto the assembly.

Stylus Part No. 069-MG2801-01R*

*Consumer Replaceable Part (See page 34 to order.)

COMPUTER REQUIREMENTS (TVT2002 ONLY)

PC REQUIREMENTS:

• Windows7(32bit)

• WindowsVista(32bit)

• WindowsXP(32bit)

MAC REQUIREMENTS:

The Vinyl Recorder software is not available for

Macintosh. Audacity is recommended for Mac

users. The Audacity software, along with complete

documentation, can be downloaded for the Mac at

http://audacity.sourceforge.net.

FOR MAC AND PC: The performance of the software

is dependent upon the processing power available,

as well as the operating system in use. More capable

systems offer higher performance.

IMPORTANT NOTE REGARDING

THE INCLUDED SOFTWARE:

This manual touches the basics of the software

included. It is suggested you download the full

manual at the link provided below to utilize all the

software’s features and effects.

TDK Vinyl Recorder:http://www.cakewalk.com

NOTE: When using USB audio devices such as the

TDK Life on Record turntable, it is expected that the

drivers installed when the unit is connected to your

computing device will be used to route your audio.

This may mute or disable your previous sound card’s

driver while temporarily using the USB drivers. When

the USB device is disconnected, the normal audio

card drivers will be used again. Depending on the

system and the hardware installed, you may need

to adjust which audio drivers are used by navigating

to the Control Panel, clicking on Sounds and Audio

Devices and then clicking on the audio tab and

adjusting your default playback or recording device

according to your needs. Typically this is seamless

and does not require any user interaction.

Imation Confidential - Use Only By Permission

Controlled material extracted from Matrix on Aug 24, 2010 08:31:11 AM CDT

Andere Handbücher für TVT1001BLK

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TDK Drehscheibe Handbücher

TDK

TDK TVT1001BLK Bedienungsanleitung

Beliebte Drehscheibe Handbücher anderer Marken

Gemini

Gemini CDT-05 MKII Bedienungsanleitung

Rotel

Rotel RP-820 Bedienungsanleitung

Shuman

Shuman MC-250BT Bedienungsanleitung

Stanton

Stanton STR8-150 Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW40WN Bedienungsanleitung

Crosley

Crosley McQueen CR7011-GY Bedienungsanleitung

auna

auna TT-Classic Plus Bedienungsanleitung

COMO AUDIO

COMO AUDIO Turntable Analog Bedienungsanleitung

Dual

Dual 1009 F Bedienungsanleitung

REED

REED Muse3C Bedienungsanleitung

AXIOMTEK

AXIOMTEK OPS883-H Series Bedienungsanleitung

Pioneer

Pioneer PL-71 Bedienungsanleitung

Vestax

Vestax PDX-a1 Bedienungsanleitung

Denon

Denon DP-400 Bedienungsanleitung

Dual

Dual 504 Bedienungsanleitung

Audio-Techica

Audio-Techica AT-LP60XBT Bedienungsanleitung

Goldring

Goldring G99 Bedienungsanleitung

Acoustic Signature

Acoustic Signature Typhoon NEO Bedienungsanleitung