TE Connectivity 1213819-1 Referenzhandbuch

409--10058

Customer Manual

Straight- Action Adapter Battery

1of 8

LOC B

E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

TOOLING ASSISTANCE CENTER

1--800--722-- 1111

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

13 JUL 11 Rev E

Powered Crimp Tool Kit 1213819- [ ]

READ THIS FIRST ! 2.........................

SAFETY PRECAUTIONS

1. INTRODUCTION 4...................................................

2. RECEVING/INSPECTION 5.............................................

3. DIE INSTALLATION AND REMOVAL 5....................................

3.1. Die Set Installation 6..............................................

3.2. Die Set Removal 6...............................................

4. OPERATION 6......................................................

4.1. Battery Installation and Removal 6....................................

4.2. Crimping 6.....................................................

5. PREVENTIVE MAINTENANCE 7........................................

5.1. Daily Maintenance 7..............................................

5.2. Yearly Maintenance 7..............................................

6. SPARE PARTS 7....................................................

7. TROUBLESHOOTING 7...............................................

8. RETURN/REPAIR 8..................................................

9. REVISION SUMMARY 8...............................................

Safeguards are designed into this application equipment to protect operators and

maintenance personnel from most hazards during equipment operation. However,

certain safety precautions must be taken by the operator and repair personnel to

avoid personal injury, as well as damage to the equipment. For best results,

application equipment must be operated in a dry, dust--free environment. Do not

operate equipment in a gaseous or hazardous environment.

DALWAYS wear appropriate ear protection.

DALWAYS wear appropriate eye protection.

DALWAYS wear approved eye protection when operating powered equipment.

DALWAYS keep guard(s) in place during normal operation.

DNEVER wear loose clothing or jewelry that may catch in moving parts of the

application equipment.

DNEVER insert hands into installed application equipment.

DNEVER alter, modify, or misuse the application equipment.

ORIGINAL INSTRUCTIONS

409- 10058

Rev E2of 8

SAFETY PRECAUTIONS - - IMPORTANT SAFETY INFORMATION

DANGER

DANGER This unit should only be used by trained

competent personnel.

Read and understand the entire manual

before using the equipment.

Always wear approved eye protection

when using the equipment.

NOTE: Keep all decals clean and legible, and replace

when necessary.

CAUTION

409- 10058

Rev E 3of 8

TOOLING ASSISTANCE CENTER

CALL TOLL FREE 1 - 800 - 722 - 1111 (CONTINENTAL UNITED STATES AND PUERTO RICO ONLY)

The Tooling Assistance Center offers a means of providing technical assistance when required.

In addition, Field Service Specialists are available to provide assistance in the adjustment or repair of the

application equipment when problems arise which your maintenance personnel are unable to correct.

INFORMATION REQUIRED WHEN CONTACTING THE TOOLING ASSISTANCE CENTER

When calling the Tooling Assistance Center regarding service to equipment, it is suggested that a person

familiar with the device be present with a copy of the manual (and drawings) to receive instructions. Many

difficulties can be avoided in this manner.

When calling the Tooling Assistance Center, be ready with the following information:

01. Customer name

02. Customer address

03. Person to contact (name, title, telephone number, and extension)

04. Person calling

05. Equipment number (and serial number if applicable)

06. Product part number (and serial number if applicable)

07. Urgency of request

08. Nature of problem

09. Description of inoperative component(s)

10. Additional information/comments that may be helpful

BATTERY TOOL KIT REGION OF USE BATTERY CHARGER BATTERY CHARGER

VOLTAGE

RAM RETRACT

SWITCH

1213819--1 North America 1725840--1 110 V Yes

1213819--2 Europe 1725840--2 220 V Yes

1213819--3 North America 1725840--1 110 V No

1213819--4 Europe 1725840--2 220 V No

1213819--5 United Kingdom 1725840--3 220 V Yes

409- 10058

Rev E4of 8

Figure 1

Release Switch

(1213819--1, --2,

and --5 Only)

Battery Powered

Crimp Tool

Battery

Lock

Battery

Cartridge

1725839--1

Trigger

Moving Die

Holder

Stationary Die

Holder

Straight--Action

Adapter

1. INTRODUCTION

Straight--Action Adapter Battery Powered Crimp Tool Kit 1213819--[ ] consists of the battery powered crimp tool

(with the Straight--Action Adapter assembly installed), as well as two rechargeable battery cartridges

(1725839--1) to power the tool. See Figure 1. Each kit has a battery charger. The battery charger part number,

its voltage, and the kit’s region of use are listed in the table on Page 3. A battery tool may have a release

switch to retract the ram as listed in the table below. The Straight--Action Adapter Battery Powered Crimp Tool

Kit 1213819--[ ] is designed to accept various crimping die assemblies that are sold separately and are

available from TE Connectivity. For crimping die set information concerning wire preparation, crimping

procedures, maintenance, inspection, and repair, refer to the applicable instructions for the appropriate

crimping die set.

Specifications are listed in Figure 2.

409- 10058

Rev E 5of 8

CRIMP TOOL (with Battery Installed)

Length 343 mm [13.5 In.]

Width 60 mm [2 3/8 In.]

Depth 80 mm [3 1/8 In.]

Mass/Weight (w/Battery) 1.3kg[2.9lb.]

Sound Level 75 dBA at 1 Meter

Vibration <2.5m/s2

Hydraulic Oil Shell TellusT15

CRIMPING CAPACITIES

Maximum Crimping Force 15.6 kN [1.75 Tons]

Average Crimping Time 2 Seconds

Average Crimps Per Charge Approximately 150

BATTERY

Charging Voltage 9.6 V

Charging Time 40 Min

Figure 2

2. RECEIVING/INSPECTION

The Straight--Action Battery Powered Crimp Tool Kit 1213819--[ ] is thoroughly inspected during and after

assembly. Prior to packaging and shipping, a final series of tests and inspections is made to ensure proper

function of the tool. The following inspection should be performed as a safeguard against potential problems

generated in transit.

1. In a well--lighted area, carefully uncrate the tool and inspect each component as it is removed from

the crate.

2. Thoroughly inspect each component for evidence of damage that may have occurred in transit. If any

of the components are damaged, file a claim against the carrier and notify TE immediately.

3. Keep this manual and all drawings and product samples with the tool for the benefit of operation and

maintenance personnel.

The crimp tool should be inspected at regularly scheduled intervals, depending on care, degree of operator

skill, the type and size of product being crimped, and environmental conditions. At a minimum, the tool should

be inspected after every 40 hours of use.

3. DIE INSTALLATION AND REMOVAL

Do not operate the tool without the Straight--Action Adapter installed. Damage to the ram or seals can result.

Do not operate the tool without a die set installed. Damage to the adapter can result.

Straight--Action Adapter Battery Powered Crimp Tool Kit 1213819--[ ] comes with the straight--action adapter

assembly already installed on the battery--powered hand tool. The only installation required is the installation of

the dies.

To avoid personal injury, be sure to exercise extreme caution when handling the crimp tool. Remove the battery before

installing or removing the dies.

CAUTION

DANGER

409- 10058

Rev E6of 8

3.1. Die Set Installation (Figure 3 )

If dies to be installed in the tool require insulation adjustment, refer to the instruction sheet packaged with the

dies for adjustment, then proceed as follows:

1. Remove the battery from the tool.

2. Mate the die assembly and insert it into the tool yoke. See Figure 3.

3. Position the stationary die in the stationary die holder. Turn the die retaining screw sufficiently to hold

the die in place. Do not tighten the screw.

4. Position the moving die in the moving die holder. Turn the die retaining screw sufficiently to hold the

die in place. Do not tighten the screw.

5. Replace the battery and check the alignment by pulsing the trigger to (slowly) close the dies, making

sure the anvil and indenter are properly aligned.

6. With the dies closed, tighten the die retaining screws.

Figure 3

Moving

Die

Color Code

Stationary

Die

Locator Die Retaining Screw

Dies Installed in Tool Yoke

3.2. Die Set Removal

To remove or change the dies, simply loosen the die retaining screws and remove the dies.

4. OPERATION

4.1. Battery Installation and Removal (Refer to Figure 1)

The Batteries Directive 2006/66/EC introduces new requirements from September 2008 on removability of batteries

from waste equipment in EU Member States. To comply with this Directive, this device is designed to allow the

rechargeable battery pack to be easily removed by the end--user when it needs to be replaced.

To install the battery, slide the battery into the bottom of the crimp tool until it can go no further. There will be an

audible “click” of the battery lock to indicate that the battery has been properly installed.

To remove the battery, disengage the battery lock by applying pressure on the lock toward the bottom of the

tool and slide the battery away from the tool.

Always dispose of the old battery pack in an environmentally--responsible way, in accordance with local waste

regulations. Where possible, please recycle the battery cartridge. Contact your local authority for details of battery

recycling locations in your area.

4.2. Crimping

The following procedure provides only general information concerning crimping. Refer to the instructions

packaged with the dies for detailed information, including wire stripping dimensions and instructions for

positioning terminals and splices in the dies.

NOTE

DANGER

409- 10058

Rev E 7of 8

To avoid personal injury, keep fingers clear of the crimping area.

To operate the Straight--Action Adapter Battery Powered Crimp Tool 1213819--[ ]:

1. Insert the terminal into the dies.

2. Depress the trigger to advance the moving jaw in order to hold the terminal in place. Do NOT deform

the terminal body.

3. Place a pre--stripped wire in the barrel of the terminal.

4. Depress and hold the trigger to complete the crimp. The crimp tool returns automatically to the first

position of its cycle when the crimp is complete.

If it is necessary to retract the ram before a crimping cycle is completed, push the release switch. Pushing the release

switch will result in the complete retraction of the ram. Only kits 1213819--1, --2, and --5 have a release switch.

This tool is not designed for continuous operation. After 100 cycles, allow the crimp tool to cool for 15 minutes.

5. PREVENTIVE MAINTENANCE

5.1. Daily Maintenance

Perform the following maintenance on a daily basis:

1. Inspect the die set, adapter assembly for wear or damage such as cracks, gouges, or chips.

2. Inspect the crimp tool for damage or leaks. If damage is detected, return the tool to TE for repair

3. Clean the tool, removing accumulations of dirt and grease on the head, particularly in areas where the

dies are installed and terminals are crimped. Wipe the entire tool frequently with a clean, lint--free cloth.

DO NOT use objects that could damage the tool.

4. Make sure that the die retaining screws are in place and are tight.

5.2. Yearly Maintenance

Once a year, or every 10,000 cycles (whichever comes first) The Straight--Action Adapter Battery Powered

Crimp Tool should be returned to TE for inspection.

6. SPARE PARTS

SBattery: 1725839--1

SCharger: 1725840--1 (120 V, US), 1725840--2 (220 V, EU), 1725840--3 (220 V, UK)

7. TROUBLESHOOTING (Figure 3)

Prior to beginning troubleshooting procedures, be sure the battery is operational.

1. Be sure that the battery is charged. Recheck the battery after several minutes to ensure that the

battery is holding its charge.

2. Use a nonflammable contact cleaner or pencil eraser to clean the the electrical contacts on the

battery and crimp tool.

3. Reinstall the battery and check the crimp tool again.

DANGER

NOTE

CAUTION

409- 10058

Rev E8of 8

PROBLEM PROBABLE CAUSE REMEDY

Dirt, contaminants, etc, in ram area of tool Return tool to TE.

Tool is inoperative. Crimp tool battery contacts damaged Reform the contacts.

Tool components are worn or damaged. Return tool to TE.

Oil level is low. Return tool to TE.

Dies stop during operation. Air in the hydraulic system.

Pull the trigger and hold the retract button

simultaneously. Hold for approximately 10

seconds.

Crimp tool loses oil. Damaged internal seal. Return tool to TE.

Figure 4

8. RETURN

Order replacement parts through your TE Representative, or call 1.800.526.5142; or send a facsimile of your

purchase order to 1.717.986.7605; or write to:

CUSTOMER SERVICE (38--35)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105--3608

9. REVISION SUMMARY

SUpdated document to corporate requirements

SAdded new text to Section 4, OPERATION

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

TE Connectivity:

1213819-3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TE Connectivity Elektrowerkzeuge Handbücher

TE Connectivity

TE Connectivity ERGOCRIMP Bedienungsanleitung

TE Connectivity

TE Connectivity 2393336-1 Bedienungsanleitung

TE Connectivity

TE Connectivity SDE-SA Bedienungsanleitung

TE Connectivity

TE Connectivity 2844990-1 Referenzhandbuch

TE Connectivity

TE Connectivity 2031676-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 59275 Bedienungsanleitung

TE Connectivity

TE Connectivity 2390276-1 Bedienungsanleitung

TE Connectivity

TE Connectivity Hand tool for AMP DUOPLUG 2.5 Bedienungsanleitung

TE Connectivity

TE Connectivity 1976330-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 1055258-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2396645-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 58536-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 46447 Bedienungsanleitung

TE Connectivity

TE Connectivity 2389783-1 Bedienungsanleitung

TE Connectivity

TE Connectivity NanoMQS 2280687-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2363758-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2390076-1 Bedienungsanleitung

TE Connectivity

TE Connectivity PRO- CRIMPER III Bedienungsanleitung

TE Connectivity

TE Connectivity PRO-CRIMPER III Bedienungsanleitung

TE Connectivity

TE Connectivity SDE-SA Bedienungsanleitung

TE Connectivity

TE Connectivity 2377026-1 Bedienungsanleitung

TE Connectivity

TE Connectivity SDE-SA Bedienungsanleitung

TE Connectivity

TE Connectivity HT11K Bedienungsanleitung

TE Connectivity

TE Connectivity 2393337-1 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch