TE Connectivity 408-160034 Bedienungsanleitung

Instruction Sheet

1 of 8

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-160034

06 NOV 20 Rev A

NOTE

All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches].

Unless otherwise specified, dimensions have a tolerance of ±0.13 [±.005] and angles have a tolerance of ±2°. Figures and

illustrations are for identification only and are not drawn to scale.

1. INTRODUCTION

The Manual Arbor Press with Removable Tooling Packs is designed to crimp TE AmplivarTM splice product on

strip. It has two styles of Tooling Packs, one for terminating AmplivarTM splices in a through splice configuration

and one for terminating AmplivarTM splices in a pig-tail splice configuration.

2. DESCRIPTION

The Manual Arbor Press with Removable Tooling Packs consists of a main Manual Arbor Press assembly

2380993-[] and pig-tail (ie 2380996-[]) or through (ie 2380997-[]) splice style Tooling Packs that can be

installed and removed from the arbor press assembly. The Arbor Press and Tooling Packs are sold separately.

Each Tooling Pack includes the necessary tooling to feed a specific splice, shear the splice from its carrier, and

crimp each splice terminal to magnet or lead wire. The Manual Arbor Press is outfitted with a stroke limiter

mechanism that requires the operator to make a full stroke of the arbor press ram before allowing the ram to

return to top dead center. This feature ensures that all terminations are produced at a consistent crimp height.

The Manual Arbor Press also includes a shut height coarse adjustment and fine adjustment with increments of

0.02mm/.0008”. All Tooling Packs include a terminal lubricator assembly.

NOTE

Use terminal lube with this equipment to improve crimp consistency and reduce crimp forces.

Figure 1

Manual Arbor Press with Removable

Tooling Packs

408-160034

Rev A

2 of 8

3. OPERATION

1. Manual Arbor Press

a. The Manual Arbor Press has a hand lever which the operator rotates forward to move the ram from its

top dead center position to its full bottom dead center position. The press stroke limiter does not allow

the press to return to top dead center until it reaches its full bottom dead center position. If necessary,

the stroke limiter can be overridden by pulling out its front spring-loaded knob and allowing the lever

and press ram to return to their top dead center position.

Figure 2

2. Tooling Packs

a. The Tooling Packs are installed into the Manual Arbor Press by sliding the square nuts attached to the

base plate of the Tooling Pack into the T-slot of the Arbor Press base. Before tightening the base plate

screws, pull out the locking plunger and raise the top plate of the Tooling Pack until it engages the

stepped ram collar. Release the locking plunger. Then tighten base plate screws to fully fasten the

Tooling Pack into the Manual Arbor Press.

Figure 3

408-160034

Rev A

3 of 8

b. Use terminal lube when producing terminations with this equipment. Each Tooling Pack includes a

lubricator with a wick that applies terminal lubricant to the terminals before being fed through the strip

guide.

NOTE

TE Connectivity recommends Stoner E805 terminal lubricant.

c. To feed terminals into the Tooling Pack, the operator must manually release the spring-loaded drag

and carefully feed the terminal strip through the strip guide until the spring-loaded feed finger snaps

behind the first terminal. Pull the manual spring-loaded feed mechanism forward as many times as

needed until a terminal is presented over the anvil. To feed properly, the feed mechanism must be

pulled fully forward until it contacts the forward stop.

d. To remove the terminal strip from the Tooling Pack, the operator must manually release the spring-

loaded feed finger, manually release the spring loaded drag, and pull the strip of terminals out of the

strip guide.

Figure 4

e. Tooling Pack (Pig-Tail Splice Configuration) Wire Termination Process

(1) If needed, manually feed terminal strip forward over anvil using feed mechanism.

(2) With one hand, properly position the magnet or stranded lead wires over wire staging area.

(3) With the other hand, pull the Manual Arbor Press hand lever forward until it reaches the fully

rotated position and the stroke limiter of the Arbor Press releases.

(4) Allow the Arbor Press hand lever to release to the top dead center position and remove the

terminated wire.

f. Tooling Pack (Through Splice Configuration) Wire Termination Process

(1) If needed, use the feed mechanism to manually feed the terminal strip forward over the anvil.

(2) Use the spring-loaded wire clamp to stage the stranded lead wire or magnet wire from the

backside of tooling and properly position the end of the wire to be terminated over the crimp

area.

(3) With one hand, properly position magnet or stranded lead wires from frontside of tooling and

properly position end to be terminated over crimp area.

(4) With the other hand, pull the Manual Arbor Press hand lever forward until it reaches the fully

rotated position and the stroke limiter of the Arbor Press releases.

(5) Allow the Arbor Press hand lever to release to the top dead center position and remove the

terminated wire.

408-160034

Rev A

4 of 8

Figure 5

4. ADJUSTMENTS

1. Manual Arbor Press

a. Shut Height Coarse Adjustment

(1) Loosen the three socket head cap screws on the rear of the Arbor Press frame.

(2) Under the top cover, attach the crank to the end of the lead screw and rotate to lift or lower the

press head assembly.

(3) When the desired height is achieved, retighten the three socket head cap screws.

Figure 6

408-160034

Rev A

5 of 8

b. Shut Height Fine Adjustment

(1) Loosen the fine adjust head clamping screw.

(2) Turn the adjust ring clockwise to increase shut height or counter-clockwise to decrease shut

height.

(3) Retighten the fine adjust head clamping screw.

NOTE

Each line on the fine adjust head scale corresponds to a shut height adjustment increment of 0.02mm[.0008”].

Figure 7

c. Hand Lever Angle Adjustment

(1) Loosen the screw to release the handle spline from the split clamp.

(2) Adjust the angle of the hand lever as needed.

(3) Retighten the screw to clamp the handle spline in the split clamp.

Figure 8

408-160034

Rev A

6 of 8

d. Moving Toggle Link Position

NOTE

Tooling Packs only function with the toggle link installed in position #2.

(1) Remove the set screws from the position #1 set screw holes.

(2) Pull out the groove pin.

(3) Move the toggle link to line up with the position #2 groove pin hole.

(4) Install the groove pin into the position #2 groove pin hole.

(5) Install and tighten the set screws into the position #2 set screw holes.

Figure 9

2. Tooling Packs

a. Terminal Drag Pressure

(1) Drag pressure can be increased or decreased by tightening or loosening the nuts that retain

the drag compression springs.

b. Terminal Feed Finger Pressure

(1) Feed finger pressure can be increased or decreased by tightening or loosening the threaded

spring plunger that biases the feed finger against the terminal strip.

Figure 10

408-160034

Rev A

7 of 8

c. Terminal Feed Position

(1) A strip of terminals must be loaded into the strip guide and fed forward until the end terminal is

exposed out the frontside of the strip guide and over the anvil.

(2) Adjust the forward feed mechanism stop position. To adjust, pull the manual feed mechanism

handle forward until it is biased against the forward feed mechanism stop position screw.Turn

the screw clockwise or counter-clockwise until terminal is visually centered over the anvil.

When the desired position is achieved, lock down the forward feed mechanism stop position

screw by tightened the locking nut while carefully making sure the adjustment position is

maintained.

(3) Adjust the rear limit stop collar. To adjust, loosen the set screws securing the rear limit stop

collar. Manually adjust the rear limit stop collar position so that the feed mechanism has

enough back stroke to pick up the next terminal when it retracts. Include some over-travel to

allow the spring-loaded feed finger to snap behind the next terminal.

Figure 11

d. Tooling Pack Mounting Orientation

NOTE

Mounting orientation position #1 is the preferred mounting for most applications.

(1) Four tooling pack mounting orientations are possible. The orientation can be adjusted by

moving the mounting screw and square nuts to a different mounting hole location (Figure 12).

Figure 12

408-160034

Rev A

8 of 8

e. Shear Tonk (Through-Splice Configuration Tooling Packs Only)

NOTE

A shear tonk adjustment may need to be made as the crimp height is adjusted.

(1) The shear tonk screw needs to be adjusted lower if the floating shear is not traveling far

enough during the crimping cycle to shear the carrier properly. It may need to be adjusted

higher if the floating shear is traveling too far and either bottoming or causing an unwanted

bend in the backside through splice wire.

(2) To adjust, loosen the shear tonk nut, turn the shear tonk screw clockwise or counter-clockwise

to adjust the shear tonk height as desired, and retighten the shear tonk nut while carefully

making sure the adjustment position is maintained.

Figure 13

5. ORDERING INFORMATION/REPLACEMENT PARTS

Phone 1-800-526-5142

CUSTOMER SERVICE (038-035)

TE CONNECTIVITY CORPORATION

PO BOX 3608

HARRISBURG, PA 17105-3608

Inhaltsverzeichnis

Andere TE Connectivity Elektrowerkzeuge Handbücher

TE Connectivity

TE Connectivity 2393336-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2390408-1 Bedienungsanleitung

TE Connectivity

TE Connectivity MATE-AX 2335290-1 Bedienungsanleitung

TE Connectivity

TE Connectivity SDE-SA Bedienungsanleitung

TE Connectivity

TE Connectivity 539 666-2 Bedienungsanleitung

TE Connectivity

TE Connectivity 1213819-1 Referenzhandbuch

TE Connectivity

TE Connectivity 2430768-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2155369 Bedienungsanleitung

TE Connectivity

TE Connectivity SOLARLOK PN 1-1579004-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 354940-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2063527-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2405856-1 Bedienungsanleitung

TE Connectivity

TE Connectivity CAPI-6T Bedienungsanleitung

TE Connectivity

TE Connectivity SDE-SA Bedienungsanleitung

TE Connectivity

TE Connectivity 2395361-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 58536-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2389862-1 Bedienungsanleitung

TE Connectivity

TE Connectivity NanoMQS 2280687-1 Bedienungsanleitung

TE Connectivity

TE Connectivity SDE-SA Bedienungsanleitung

TE Connectivity

TE Connectivity SDE-SA Bedienungsanleitung

TE Connectivity

TE Connectivity 2363592-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2844990-1 Referenzhandbuch

TE Connectivity

TE Connectivity OCEAN 2.0 Bedienungsanleitung

TE Connectivity

TE Connectivity 47386-4 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch