TE Connectivity 2255140-1 Bedienungsanleitung

1 of 4

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

TOOLING ASSISTANCE CENTER

1-800-722-1111

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

Instruction Sheet

408-32126

13 MAR 15 Rev A1

Figure 1

1. INTRODUCTION

This instruction sheet covers the use of TE Connectivity Hand Crimping Straight Action Hand Tools (SAHT)

2255139-1, 2255140-1, 2255141-1, and 2255142-1 with flip locators which crimp D1000 Dynamic Series

contacts listed in Figure 2.

NOTE

Dimensions are in metric units with [inches in brackets]. Figures and illustrations are for reference only and are not drawn to

scale.

Read these instructions thoroughly before crimping

any contacts.

2. DESCRIPTION (Figure 1 and Figure 3)

The FRONT OF TOOL (contact side), is where the contact is inserted. The BACK OF TOOL (wire side), is

where the wire is inserted and has the wire size markings above each crimp section.

Each tool features a fixed die (crimper), a movable die (anvil), two crimp sections with applicable wire size

markings, a flip locator, a wire stop, and a ratchet release lever.

Once engaged, the ratchet will not release until the handles have been FULLY closed.

CAUTION

The ratchet ensures full crimping of the contact. This is a design feature that ensues maximum electrical and tensile

performance of the crimp. Do NOT readjust the ratchet.

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low

volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Mini Straight Action Hand Tools (SAHT)

2255139-1, 2255140-1, 2255141-1, and

2255142-1 for D1000 Dynamic Series

Contacts

Crimper

Back of Tool

Ratchet

Anvil

NOTE: 2255139-1 is

Shown, but Other SAHTs on

this Document are Similar

0000

ORIGINAL INSTRUCTIONS

408-32126

Rev A1

2 of 4

The flip locator positions the contact in the crimping die, and the wire stop aids in locating the wire in the

contact. In use, it rests in the transition area of the connector. See Figure 1 and Figure 3.

The flip locator prevents the contact from bending during the crimping procedure.

The ratchet release lever enables the user to open the partially closed tool handles when necessary.

The ratchet is used to control the crimp height of the terminal’s wire barrel and ensures full crimping of the

terminal.

Figure 2

3. CRIMPING PROCEDURE

Refer to the table in Figure 2 and ensure compatibility between the wire, contact, and crimping tool. Wire size

must be within the specified range for the contact. Strip the wire to the length indicated.

CAUTION

Do NOT cut or nick the wire strands.

The hand crimping tool must be the one designed for crimping the wire and contact. Identify the appropriate

crimp section (according to the wire size markings on the BACK of the tool).

Refer to Figure 3 and proceed as follows:

1. Hold tool so BACK (wire side) is facing you.

2. Make sure the ratchet is released by squeezing the tool handles and allowing them to open FULLY.

3. Open flip locator. Insert contact into the flip locator (make sure contact is inserted properly).

4. Close flip locator.

5. Pre-close the handles slightly, and insert the wire into the contact.

6. Close the handles until the automatic ratchet releases.

7. Open flip locator. Take wire with contact out of

locator.

Wire Strip Length 1.7 to 2.3

[.067 to .090]

WIRE SIZE

(AWG)

CONTACT

CRIMP

SECTION (WIRE

SIZE MARKING)

HAND TOOL

1827586-2

1903115-2

2255139-1

28-26

1827587-2

1871743-1

1903116-2

1903124-1

1939992-2

28-26

2255140-1

24-22 24-22

28-26

1827588-2

1871744-1

1903117-2

28-26

2255141-1

24-22 24-22

22-20

1827589-2

1871745-1

1903118-2

1903126-1

22-20

2255142-1

18 18

408-32126

Rev A1

3 of 4

Figure 3

4. TOOL CERTIFICATION

These instructions have been approved by TE Design, Production, and Quality Control Engineers to provide

documented maintenance and inspection procedures.

Through TE test laboratories and the inspection of production assembly, the procedures described herein have

been established to ensure quality and reliability of TE hand crimping tools.

5. INSPECTION PROCEDURES

5.1. Daily Maintenance

It is recommended that each operator of the tool be made aware of, and responsible for, the following four

steps of daily maintenance:

1. Remove dust, moisture, and other contaminants with a clean brush, or a soft lint-free cloth. Do NOT

use objects that could damage the tool.

2. Make sure the proper retaining pins are in place and secured with the proper retaining rings.

3. Make certain all pins, pivot points, and bearing surfaces are protected with a THIN coat of any good

SAE No. 20 motor oil. Do NOT oil excessively.

4. When the tool is not is use, keep the handles closed to prevent objects from becoming lodged in the

crimping dies and store the tool in a clean dry area.

5.2. Periodic Inspection

Regular inspections should be performed by quality control personnel. A record of scheduled inspections

should remain with the tool and/or be supplied to supervisory personnel responsible for the tool. Through

recommendations call for at least one inspection a month, the inspection frequency should be based on the

amount of use, ambient working conditions, operator training and skill, and established company standards.

These inspections should be performed in the following sequence:

Visual Inspection

1. Remove all lubrication and accumulated film by immersing the tool (handles partially closed) in a

suitable commercial degreaser that will not affect paint or plastic material.

2. Make certain all retaining pins are in place and secured with retaining ring.

3. Close the tool handles until the ratchet releases, then allow handles to open freely. If they do not open

quickly and fully, return the tool to TE for evaluation and repair.

Flip Locator

408-32126

Rev A1

4 of 4

Inspect the head assembly with special emphasis on checking for worn, cracked, or broken die. If damage to

any part of the head assembly is evident, return the tool to TE for evaluation and repair.

Crimp Height Inspection

This inspection requires the use of a micrometer with a modified anvil as shown in Figure 4.

Proceed as follows:

Refer to the table in Figure 4 and select a contact and a wire (maximum size) for each crimp section listed

in the table.

1. Refer to Section 3, CRIMPING PROCEDURE and crimp the contact(s) accordingly.

2. Using a crimp height comparator, measure the wire barrel height as shown in Figure 4. If the crimp

height conforms to that shown in the table, the tool is considered dimensionally correct. If not, return

the tool to TE for evaluation and repair.

TE does not market crimp height comparators. Refer to Instruction Sheet 408-7424 for detailed

information on obtaining and using a crimp height comparator.

Figure 4

6. REVISION SUMMARY

Changed format.

HAND

TOOL CONTACT

CRIMP SECTION

(WIRE SIZE

MARKING)

CRIMP HEIGHT

DIMENSION “A”

2255139-1

S 1827586-2

1903115-2

0.54 ±0.05

[.021 ±.002]

28 0.57 ±0.05

[.022 ±.002]

2255140-1

1827587-2

1871743-1

1903116-2

1903124-1

1939992-2

28-26 0.64 ±0.05

[0.25 ±.002]

24-22 0.74 ±0.05

[.029 ±.002]

2255141-1

1827588-2

1871744-1

1903117-2

1903125-1

28-26 0.64 ±0.05

[0.25 ±.002]

24-22

0.74 ±0.05

[.029 ±.002]

2255142-1

1827589-2

1871745-1

1903118-2

1903126-1

22-20 0.85 ±0.05

[.033 ±.002]

18 1.15 ±0.05

[.045 ±.002]

Dieses Handbuch passt für folgende Modelle

Andere TE Connectivity Werkzeuge Handbücher

TE Connectivity

TE Connectivity 90331- 1 Bedienungsanleitung

TE Connectivity

TE Connectivity CERTI-CRIMP II Referenzhandbuch

TE Connectivity

TE Connectivity CERTI- LOK Hand Tool Frame Assembly 169400 Bedienungsanleitung

TE Connectivity

TE Connectivity SDE-SA Bedienungsanleitung

TE Connectivity

TE Connectivity 2430769-1 Bedienungsanleitung

TE Connectivity

TE Connectivity OCEAN 2.0 Bedienungsanleitung

TE Connectivity

TE Connectivity 2379255-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2255143-1 Bedienungsanleitung

TE Connectivity

TE Connectivity CXP 2018681-1 Bedienungsanleitung

TE Connectivity

TE Connectivity HT11K Bedienungsanleitung

TE Connectivity

TE Connectivity SDE-SA Bedienungsanleitung

TE Connectivity

TE Connectivity PRO-CRIMPER III Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 6-1579014-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 1725062-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2215038-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 58024-1 Bedienungsanleitung

TE Connectivity

TE Connectivity Ocean 1.0 Bedienungsanleitung

TE Connectivity

TE Connectivity TERMI-POINT 59865-1 Referenzhandbuch

TE Connectivity

TE Connectivity 768338-2 Bedienungsanleitung

TE Connectivity

TE Connectivity 58372- 1 Bedienungsanleitung

TE Connectivity

TE Connectivity 734185-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 354711-1 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung