Teac VS-R265 Bedienungsanleitung

VS-R265／VS-R264

Guide to point-to-point streaming (unicast) between different

networks

TEAC Corporation

Issued October 2020 (revised December 2021)

It is necessary to secure a stable bandwidth to

establish a stable streaming between bases in

different networks. Please consult with a

network contractor in case construction is

needed.

＜Table of contents＞

・Required equipment

・Connection

1. Encoder side setup

(1) PC setup

(2) VS-R265 setup

Confirming the settings

2. Decoder side setup

(1) PC setup

(2) VS-R265 setup

(3) Router setup

Confirming all settings

・Troubleshooting

・・・・・・ page 3

・・・・・・ page 4~5

・・・・・・ page 6

・・・・・・ page 7~11

・・・・・・ page 12

・・・・・・ page 13

・・・・・・ page 14~18

・・・・・・ page 19

・・・・・・ page 20

・・・・・・ page 21

・Required equipment

【Encoder side】

VS-R265 (or VS-R264 ) 1 set

PC (for setup) 1 set

Router 1 set

Camera(s) or other visual equipment 1 set

【Decoder side】

VS-R265 (or VS-R264 ) 1 set

PC (for setup) 1 set

Router 1 set

Video monitor 1 set

Note: AC adapters and other accessories are omitted from this list.

・Connection: Connect as shown in the picture below.

VS-R265 ①

Router ①

LAN

Global IP ①

WAN

Router ②

LAN

Global IP ②

e.g. 60.###.###.88

VS-R265 ②

Decoder side

Encoder side

Port no. 6400 (e.g.)

LAN

Video

monitor

HDMI

Camera(s),

etc.

HDMI

LAN

・Connection

① Obtaining the global IP address (public IP address) of the decoder’s network

Connect the computer and the decoder on the same network and search “what is my IP” on

Google (*1). Write down the network’s global IP address.

e.g. 60.###.###.88 (*2)

*１: The global IP address may differ depending on whether the decoder is connected or not. Also,

the global IP address will be reassigned and may change if the router settings are changed

and then rebooted.

*２:“###“ represent whole numbers between 1~255

② Setting the port number transferred by the decoder’s network

The user can freely set the port number using even numbers between 1024 - 49150. Write down

the port number once decided.

In this guide, the port number will be 6400.

1. Encoder side setup

(1) PC setup

Since the VS-R265’s factory default private IP address is 192.168.1.100, this guide will use this

initial value to set the computer’s private address.

IP address : 192.168.1.19 (*1)

Sub-net mask : 255.255.255.0

Default gateway : 192.168.1.1 (*2: router’s IP address)

*1: The IP addresses above are just examples. They can be set arbitrarily as long as they have the same network

address.

Both PC and VS-R265 can be set to “Automatic (DHCP)”.

*2: In case of Windows, the IP address settings can be changed from

Control Panel > All Control Panel Items > Network Connections

1. Encoder side setup

(2) VS-R265 setup #1

①Use the TASCAM DISCOVERY application to

recognize the VS-R265 on the computer.

②Press the Open button on the right to open the

Streaming Dashboard on a browser.

Press this button to open

the Streaming Dashboard

[TASCAM DISCOVERY start screen］

Note: TASCAM DISCOVERY can be downloaded from the TASCAM

website.

1. Encoder side setup

(2) VS-R265 setup #2

③ Select “Device Settings” on the

top right of the Streaming Dashboard

screen.

④Select the Network tab on the left,

change “Address Assignment” to

“Manual (Static)”, and set the private

IP address.

In this case 192.168.1.21 (e.g.)

Note: the private IP address will be automatically

set if “Address Assignment” is set to “Automatic

(DHCP)”.

Select “Device Settings”

Chance to “Manual(Static)”

Set 192.168.1.21

[Streaming Dashboard screen]

[Device Settings > Network screen］

1. Encoder side setup

(2) VS-R265 setup #3

⑤Select the General tab on the left,

set the Encoder to ON, and save

settings.

Set the Encoder to ON and

save

[Device Settings > General screen］

1. Encoder side setup

(2) VS-R265 setup #4

⑥Select Encoder Control on the top

center. Turning ON the Encoder will

display the VS-R265 on the screen.

⑦Press the Configure button below

“Output Settings” and open the Output

Settings screen.

Press the Configure button

[Encoder Control screen］

[Output Settings画面］

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teac Medienkonverter Handbücher

Teac

Teac MC-DX90i Bedienungsanleitung

Teac

Teac UD-504 Bedienungsanleitung

Teac

Teac WS-A70 Bedienungsanleitung

Teac

Teac MC-DV639 Bedienungsanleitung

Teac

Teac UD-301 Bedienungsanleitung

Teac

Teac UD-H01 Bedienungsanleitung

Teac

Teac UD-503 Bedienungsanleitung

Teac

Teac UD-501 Bedienungsanleitung

Teac

Teac D-70 Bedienungsanleitung

Teac

Teac Esoteric D-07X Bedienungsanleitung

Teac

Teac UD701NB Bedienungsanleitung

Teac

Teac Esoteric D-05 Bedienungsanleitung

Teac

Teac Esoteric D-01 Bedienungsanleitung

Teac

Teac UD-503 Kurzanleitung

Teac

Teac UD-701N Bedienungsanleitung

Teac

Teac WS-A70 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung