Tech21 SansAmp GED-2112 Bedienungs- und Wartungshandbuch

August 2, 2017

SERVICE NOTES for GED-2112

For Qualified Technicians Only

WARNING: No user-serviceable parts inside. Opening and altering the contents within will void the

warranty unless performed by a qualified service technician.

NOTE: The following service notes are recommended as one-time only procedures. It is NOT

recommended to make these changes on a repeated basis.

DESCRIPTION:

The GED-2112 contains two internal jumpers. The first allows the outputs to be tied together so both

channels can be fed through a single output. The second is to configure the operation of the Function

Switch from “mute” to “bypass”.

1. Remove AC cable from unit.

2. Remove bottom cover for access to circuit boards. Carefully unscrew six philips head screws

securing bottom cover to chassis. Be sure to use #2 size screwdriver. Set cover and screws to

the side.

3. Jumpers are located near the FX loop return jack.

TIE JUMPER: The GED-2112 is shipped from the factory with Drive and Deep channels routed through

their respective XLR and ¼” jacks. This configuration is shown in PHOTO 1 below.

PHOTO 1

Moving the jumper to the “TIE” position will combine the Drive and Deep channels to the ¼” and XLR

Drive and Deep output jacks. Please refer to PHOTO 2 below.

PHOTO 2

FUNCTION SWITCH JUMPER: The GED-2112 is shipped from the factory with the Function Switch

operating as a mute button. Please refer to PHOTO 1 on previous page.

Moving the jumper to the “BYPASS” position will send unaffected signal through the ¼” and XLR Drive

and Deep jacks when the Function Switch is disengaged. Please refer to PHOTO 3 below.

PHOTO 3

4. After configuring jumpers to desired positions, replace bottom cover. Be sure not to over-

tighten or strip the six philips head screws.

Inhaltsverzeichnis

Andere tech21 Verstärker Handbücher

tech21

tech21 Bass Power Wedge 60 Bedienungsanleitung

tech21

tech21 SansAmp RBI Bedienungsanleitung

tech21

tech21 Landmark 300 Bedienungsanleitung

tech21

tech21 SansAmp GT2 Bedienungsanleitung

tech21

tech21 SansAmp PSA 1.1 Bedienungsanleitung

tech21

tech21 SansAmp PSA-1 Bedienungsanleitung

tech21

tech21 Trademark 60 Bedienungsanleitung

tech21

tech21 PW60 Bedienungsanleitung

tech21

tech21 Trademark 120 Bedienungsanleitung

tech21

tech21 VT BASS 500 Bedienungsanleitung

tech21

tech21 Trademark 10 Bedienungsanleitung

tech21

tech21 Trademark 30 Bedienungsanleitung

tech21

tech21 SansAmp RPM Bedienungsanleitung

tech21

tech21 Power Engine 300 Bedienungsanleitung

tech21

tech21 Trademark 60 Bedienungsanleitung

tech21

tech21 Trademark 60 Bedienungsanleitung

tech21

tech21 Bronzewood 60 Bedienungsanleitung

tech21

tech21 Landmark 600 Bedienungsanleitung

tech21

tech21 Landmark 120 Bedienungsanleitung

tech21

tech21 Bass Power Engine 60 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung