Techmaster T9530 Bedienungsanleitung

TechMaster

Lock system for safes

PROGRAMMING AND OPERATING

INSTRUCTIONS

IU_TechMaster_02_eng Page 3 of 32

Information about TechMaster ................................................................................................4

1. Master Menu...........................................................................................................................6

1.1. Set Time and Date .....................................................................................................6

1.2. Time Lock ....................................................................................................................7

1.2.1. Time Lock - Add......................................................................................................7

1.2.2. Time Lock - Verify or Delete .................................................................................8

1.2.3. Special Events - Add...............................................................................................8

1.2.4. Special Events – Verify or Delete .........................................................................9

1.2.5. Opening Periods - Add .........................................................................................10

1.2.6. Opening Periods – Verify or Delete....................................................................10

1.3. PC Link .......................................................................................................................11

1.4 Manager Management..............................................................................................11

1.5 Dynamic Codes ..........................................................................................................12

2. Manager Menu .....................................................................................................................13

2.1. Users Management – Install/Delete/Enable/Disable users................................ 13

2.2. Time Delay and Open Window ..............................................................................13

2.3. Variable Time Delay.................................................................................................14

2.3.1. Variable Time Delay - Add...................................................................................14

2.3.2. Variable Time Delay - Verify or Delete..............................................................15

2.4. PC Link .......................................................................................................................15

3. OVR Manager Menu ............................................................................................................16

3.1. Users Management – install/delete/disable user ................................................16

4. Change Code Menu .............................................................................................................17

4.1. Change Users and OVR Users Code...................................................................... 17

4.2. Change Manager Code ............................................................................................17

4.3. Change OVR Manager Code ...................................................................................18

4.4. Change Master Code ...............................................................................................18

5. Time Menu............................................................................................................................19

5.1 Opening Extension ....................................................................................................19

5.2 Immediate Time Lock...............................................................................................20

6. Configuration Menu............................................................................................................. 20

6.1. Install Locks ..............................................................................................................21

6.2. Remove Locks...........................................................................................................21

6.3. LCD Contrast.............................................................................................................22

6.4. Language...................................................................................................................22

6.5. Membrane test..........................................................................................................22

6.6. System Info...............................................................................................................23

7. Opening the Locks...............................................................................................................23

7.1. Users (or OVR Users): Opening the lock without Time Delay ..........................23

7.2. Users (or OVR Users): Opening the lock with Time Delay ................................ 23

7.3. Manager (or OVR Manager): Opening the lock

without Time Delay ...............24

7.4. Manager (or OVR Manager): Opening the lock

with Time Delay .....................25

7.5. Opening the lock with Dynamic Codes (Dallas key option)...............................26

7.6. Opening the lock with Dynamic Codes (PIN option) ..........................................27

7.7. Dual Mode: Opening

the lock without Time Delay .............................................27

7.8. Dual Mode: Opening the lock with Time Delay................................................... 28

8. Shortcuts...............................................................................................................................29

9. Optional features .................................................................................................................29

Page 4 of 32 IU_TechMaster_02_eng

Information about TechMaster

Using your keypad

To power up TechMaster press any key.

To slide the functions of a menu use the slide/change button .

To exit from one function of a menu and go back to the main menu slide the functions

until the last one (“EXIT?”) and confirm with the confirm/enter button .

Automatic power savings: LCD will power-off after 30 seconds of non-operation.

TechMaster opening and administration codes

Every user (Manager, Standard user or Override) can be a numerical code or a

numerical code + Dallas key.

Master code can be only a numerical code.

Default TechMaster codes

Default code for TechMaster are:

Master 1 2 3 4 5 6 7 8

Manager 1 2 3 4 5 6

OVR Manager 6 5 4 3 2 1

User 2 0 2 – 0 2 0 2 0 2

User 3 0 3 – 0 3 0 3 0 3

.......... ............

User XY X Y – X Y X Y X Y

Configuration Code 5 0 5 0 5 0

Factory code has to be changed, as soon as the system is initiated by the

final user.

Slide/Change

Confirm/Enter

IU_TechMaster_02_eng Page 5 of 32

Penalty

Four consecutive invalid codes initiates four minutes delay period. During this period

LCD will display the message “Penalty” when any operation will be performed.

Programming TechMaster

All the following programming instructions of TechMaster must be intended for only

one lock (this also includes Master and Manager codes). If your TechMaster has

more than one lock you must repeat the instructions for each installed lock.

Multiple Locks

TechMaster can manage up to five locks.

Time Delay

Can be set on each lock.

Delay Period: 0 – 99 minutes; Open Period: 1 – 19 minutes.

Five Time Delays can run at once.

Dallas keys

Can be set on each lock, requires code and key. Available for all Manager and Users

(not available for the Master).

TechMaster only works with Dallas keys coded by Tecnosicurezza.

Low Battery Warning

Long audio and visual signals during opening indicate low battery.

Emergency battery

If your TechMaster is powered by the mains or an internal battery box it is possible to

connect an emergency battery to the keypad in case of sudden blackout: connect a

new 9V ALKALINE battery to the battery connector located at the bottom of the

keypad.

Silent Alarm Signal

Can be set on each lock.

Remote Disable

Can be set on each lock.

Page 6 of 32 IU_TechMaster_02_eng

Audit

Each Lock will record last 900 operations with time & date, user and function.

Override Reopening

TechMaster can be set to have Override Reopening option (from 0 to 59 minutes). If

this option is set, it will be possible to reopen the lock overriding Time Delay during

the set value of time. This function is available only after a standard opening

procedure of the lock (after opening with time delay).

Important notes

Simple/trivial codes, which could be easily guessed (1,2,3,4,5,6) have to be

prevented.

Never remove lock cover, this voids the warranty.

1. Master Menu

Power up TechMaster.

Press . LCD will display the message:

MASTER MENU

X X X X X X X X

Enter Master code (default code 1-2-3-4-5-6-7-8).

1.1. Set Time and Date

Use this function to change Time and Date.

Power up TechMaster and access the Master Menu. LCD will display

the message:

SET

TIME AND DATE

Press . LCD will display current time and date.

08:00 FRI

27/01/2006

Press to modify Time and Date.

hh:mm _ _ _

DD / MM / YYYY

IU_TechMaster_02_eng Page 7 of 32

Enter new values for time and date and press to confirm.

1.2. Time Lock

Power up TechMaster and access the Master Menu. Press two

times.

TIME LOCK

1.2.1. Time Lock - Add

Use this function to add Time Lock values.

Power up TechMaster and access the Time Lock menu. Press .

STANDARD WEEK 1

To add Standard week 2 or 3 press one or two times, then

press .

Press . LCD will display the message:

ADD

Press . LCD will display the current day of the week.

!hh:mm DAY

"hh:mm

The first is Opening time and the second is Closing time.

Enter Opening and Closing time, then press .

To cancel entered values, press .

Press to confirm. LCD will display the next day of the week, and

will propose the same values. Press to confirm or to skip

and change day.

!hh:mm DAY

"hh:mm

At the end of the week LCD will display the message:

END OF LIST

EXIT AND SAVE? !

Press to save settings or to get back to the first day.

Settings will be saved when will be pressed.

Page 8 of 32 IU_TechMaster_02_eng

After saving the settings LCD will display the message:

Press to set more periods (up to 4).

ADD

1.2.2. Time Lock - Verify or Delete

Use this function to verify or delete Time Lock values.

Power up TechMaster and access the Time Lock menu. Press .

STANDARD WEEK 1

To verify or delete Standard Week 2 or 3 press one or two

times, then press .

Press , LCD will display the message:

VERIFY OR

DELETE

Press , LCD will display the set values for the first day.

!hh:mm DAY

"hh:mm

Press to scroll all the set values.

Press to delete the set values. LCD will display the message:

DELETE?

Press to confirm or press to exit.

At the end of the list press .

END OF LIST

Time Lock Standard week is an Opening Time Period: the safe door can be opened if you

enter a valid code (for ex. Opening Period from 08:00 to 14:00: the door can be opened from

08:00 to 14:00, but can’t be opened at 16:00).

You can enter four different Time Periods for each day (for ex. MON from 07:00 to 10:00;

from 12:00 to 13:00; from 15:00 to 16:00; from 18:00 to 19:00).

Time Periods will be saved just after confirmation pressing . It is recommended to set

the values with safe door open.

All the Users will be automatically added to their related Time Lock table.

1.2.3. Special Events - Add

IU_TechMaster_02_eng Page 9 of 32

Use this function to add Special Events values.

Power up TechMaster and access the Time Lock menu. Press .

STANDARD WEEK 1

Press three times.

SPECIAL EVENTS

Press , LCD will display the message:

ADD

Press , LCD will display the message:

"DD/MM/YY hh:mm

!DD/MM/YY hh:mm

The first one is the closing time and date and the second one is the opening time and date.

Enter Closing and Opening time and date, then press to confirm.

If a value for Year is set, this Special Event will cease after that date.

If a value for Year is not set, this Special Event will repeat every year.

To cancel entered values, press .

Repeat this procedure for every Special Event.

Special Events are Closing Periods: the safe’s door can’t be opened during these periods.

Up to 30 Special Events are available for a maximum of nine (9) days each.

1.2.4. Special Events – Verify or Delete

Use this function to verify or delete Special Events values.

Power up TechMaster and access the Time Lock menu. Press .

STANDARD WEEK 1

Press three times.

SPECIAL EVENTS

Press , LCD will display the message:

ADD

Press , LCD will display the message:

VERIFY OR

DELETE

Press , LCD will display the first saved Special Event.

"DD/MM/YY hh:mm

!DD/MM/YY hh:mm

Page 10 of 32 IU_TechMaster_02_eng

Press to scroll all the set values.

Press to delete the set values. LCD will display the message:

DELETE?

Press to delete the LCD values or press to exit.

At the end of the list press .

END OF LIST

1.2.5. Opening Periods - Add

Use this function to add Opening Periods values.

Power up TechMaster and access the Time Lock menu. Press .

STANDARD WEEK 1

Press four times.

OPENING PERIODS

Press . LCD will display the message:

ADD

Press . LCD will display the message:

!DD/MM/YY hh:mm

"DD/MM/YY hh:mm

The first one is the opening time and date and the second one is the closing time and date.

Enter Opening and Closing time and date, then press to confirm.

If a value for Year is set, this Opening Period will cease after that date.

If a value for Year is not set, this Opening Period will repeat every year.

To cancel entered values, press .

Repeat this procedure for every Opening Period.

During Opening Periods it will be possible to open the safe’s door even if Time Lock is active.

Up to 30 Opening Periods are available for a maximum of nine (9) days each.

1.2.6. Opening Periods – Verify or Delete

Use this function to verify or delete Opening Periods values.

Inhaltsverzeichnis

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung