Tecnoware ERA LED 0.85 Bedienungsanleitung

Uninterruptible Power Supply

ERA LED 0.65

ERA LED 0.85

ERA LED 1.1

User’s manual

UPS ERA LED 0.65 – 0.85 – 1.1 1 User’s manual

ndex

Safety Warnings ................................................................................ 2

1 ntroduction ................................................................................. 3

2 General Characteristics ................................................................... 4

3 Receipt and site selection ................................................................ 4

4 EXTERNAL DESCR PT ON .................................................................. 5

4.1 Front Panel ............................................................................. 5

4.2 Rear Si e ................................................................................ 6

5 Electrical nstallation and First Start Up ............................................... 7

6 Functioning ................................................................................. 8

6.1 Normal Mo e ........................................................................... 8

6.2 Battery Mo e ........................................................................... 8

6.3 Low Battery an Automatic Restart ................................................. 8

6.4 Loa Control ............................................................................ 9

6.5 Fault Con ition ........................................................................ 9

7 Communication nterface ................................................................. 9

8 Technical Characteristics ................................................................ 10

9 Maintenance ............................................................................... 11

9.1 UPS Cleaning ......................................................................... 11

9.2 Battery ................................................................................ 11

9.3 Battery Replacement ............................................................... 11

9.4 Operator Safety ...................................................................... 12

10 Troubleshooting ........................................................................... 12

Conformity to the European Directives ................................................... 14

Product Disposal ............................................................................... 14

Lead Batteries ................................................................................. 14

All tra emarks are property of their respective owners.

TECNOWARE s.r.l.

Via Montetrini, 2E – Loc. Molino el Piano – 50065- Pontassieve (FI) – Italy

www.tecnoware.com

E ition: May 2012 – version: 1.0

No part of this manual may be repro uce , even partially, without the

authorisation of TECNOWARE s.r.l.

TECNOWARE s.r.l. reserves the right to change specifications at any time

an without notice.

User’s manual 2 UPS ERA LED 0.65 – 0.85 – 1.1

Safety Warnings

Read this manual carefully and completely before installing and using the TECNOWARE ERA LED

Uninterruptible Power Supply, which, from here after, will also be referred to as UPS.

This manual should be kept close to the UPS and read before the UPS is installed and used.

The UPS must be used only by properly trained personnel. To ensure correct and safe

operations, it is necessary that operators and maintenance personnel observe the general

safety Standards as well as the specific instructions included in this manual.

Risk of electric shock: do not remove the cover. The UPS contains internal parts, which are at a

high Voltage and are potentially dangerous, capable of causing injury or death by electric

shock.

There are no internal parts in the UPS, which are user serviceable. Any repair or maintenance

work must be performed exclusively by qualified technical personnel authorized by

TECNOWARE. TECNOWARE declines any responsibility if this warning is disregarded.

Warning to the technical personnel authorized for Service: since internal components are

connected to the batteries, they will remain powered, and therefore dangerous, even after the

UPS has been disconnected from AC power mains. Before any repair or maintenance work,

disconnect the batteries, by removing the positive cable (red colour) from the positive pole of

the battery.

t is compulsory to ground the UPS according to Safety Standards. The AC mains power supply

socket used to power the UPS must have an earth connection.

n the event of AC main power supply failure (when the UPS works in Battery mode), do not

unplug the power supply cable to the UPS to ensure earth continuity to the connected loads.

Since the AC mains power supply cable acts as a separation device, the AC mains power socket

used to supply the UPS and/or the rear side of the UPS must be accessible to easily disconnect

the cable in case of dangerous conditions.

Risk of electric shock at the Output lines when the UPS is ON.

Risk of electric shock at the Output lines while the unit is connected to the AC utility line.

Do not obstruct ventilation slots or holes and do not rest any object on top of the UPS.

Do not insert objects or pour liquids in the ventilation holes.

nstall the UPS indoors, in a protected, clean and moisture-free environment.

Do not expose to the direct sun light.

Do not keep liquids, flammable gases or corrosive substances near the UPS.

UPS ERA LED 0.65 – 0.85 – 1.1 3 User’s manual

1ntroduction

ERA LED is a Line Interactive UPS (Uninterruptible Power Supply) specifically esigne to protect your computer

from any type of irregularities in the AC line (such as black-outs, un er or over voltages, micro-interruptions),

which often cause amage to your Har ware an Software.

Un er normal AC line con ition, ERA LED performs output voltage regulation an filters frequently occurring

electrical isturbances (such as transients, spikes, interferences, etc.), thus protecting all evices connecte to

the outlets, an recharging the batteries in an i eal way. In case of anomaly to the AC line, the UPS continues

fee ing the protecte equipment.

ERA LED is equippe with an USB interface which can be use to notify a power failure or a low battery con ition

irectly to a computer: this makes it possible to automatically save your ata uring an exten e black-out with

the most wi esprea operating systems (Win ows, Mac OS X, Linux, etc.).

Read this manual carefully before using the ERA LED; it includes important safety

warnings and useful advices for correct use and installation.

This manual is a guide that enables you to correctly install and use your ERA LED. This

manual includes important SAFETY instructions for the operator, for the UPS correct

installation, and gives useful advice on the product and battery maintenance. For any

type of problem, please refer to this manual before calling the customer service.

ERA LED is constantly being evelope an improve : consequently, your unit may iffer somewhat from the

escription containe in this manual.

This manual inclu es the following mo els:

•ERA LED 0.65 (650 VA)

•ERA LED 0.85 (850 VA)

•ERA LED 1.1 (1100 VA)

In this manual ERA LED will simply be referre to as UPS.

User’s manual 4 UPS ERA LED 0.65 – 0.85 – 1.1

2General Characteristics

ERA LED has all the a vance features, which guarantee maximum reliability an safety:

•All functions are controlle by a microprocessor, giving full guarantee of high reliability.

•Output Voltage regulation through AVR (Automatic Voltage Regulation).

•Overloa protection both in normal mo e an in battery mo e.

•High performance battery charger, which exten s the battery me ium life ensuring an optimal recharge.

•Start up even if the electrical network is not available.

•Automatic restart after an automatic shut own ue to a low battery con ition once the AC utility power

returns.

•A apts automatically to 50 or 60 Hz input frequency.

•Acoustic signals of various kin s in icating functioning mo es an alarm/fault con ition.

•Communication with the computer through USB interface.

•High efficiency

•Maximum reliability

•Smart esign an easy to use

3Receipt and site selection

Carefully remove the UPS from its packaging, an carry out a meticulous inspection. We recommen keeping the

original packaging in a secure place, in case you nee to sen the UPS for maintenance purposes. In case of

transport amage, notify the carrier an ealer imme iately.

We recommen paying attention to the below points in or er to choose a correct placement for your UPS:

•The UPS is esigne to operate in a protecte environment (e.g. offices). We therefore recommen

installing it in a place with very little or no humi ity, ust or smoke.

•In all circumstances, see the “Technical Characteristics” chapter for environmental specifications an

check that the selecte area meets these specifications.

•During normal operation the UPS ischarges a minimal amount of heat. So it is necessary to leave at least

20 cm of unobstructe space all aroun the UPS in or er to keep it properly ventilate .

•Do not obstruct ventilation holes.

•Do not insert objects or pour liqui s in the ventilation holes.

•Do not rest any object on top of the UPS.

•Do not keep liqui s, flammable gases or corrosive substances near the unit.

•Install the UPS on a properly tile floor. Avoi the installation on a floor that is not tile flat.

UPS ERA LED 0.65 – 0.85 – 1.1 5 User’s manual

4EXTERNAL DESCR PT ON

4.1 Front Panel

The front panel informs the user about operating status, alarm con itions an measurements. Front panel shown

below consists of two parts:

1. The ON/OFF button: enables the user to turn ON/OFF the UPS.

2. The L NE/BATTERY le : this le (blue color) is always on uring the functioning in Normal Mo e, it flashes

one time every 4 secon s in Battery mo e an it flashes one time every secon in Low Battery con ition.

Figure 1 – Front panel

User’s manual 6 UPS ERA LED 0.65 – 0.85 – 1.1

4.2 Rear Side

Figure 2 – Rear Side

1. Grounded AC nput power socket: IEC C14 type; to connect the UPS to the AC utility line.

2. nput fuse: electrical specification: max current 5 A, voltage 250 V.

3. Grounded UPS Output receptacles: IEC C13 type, black colour, to supply critical loa s.

4. Computer nterface (USB connector): it is the communication USB port.

n case of anomaly to the AC line (black-out), the UPS Output receptacles (black colour,

#3) continue supplying the correct power to all connected equipment.

UPS ERA LED 0.65 – 0.85 – 1.1 7 User’s manual

5Electrical nstallation and First Start Up

We a vise you to follow the steps below explaine for greater safety:

1. Switch off all the evices (Personal Computer or other electronic evices) that nee to be supplie by the

UPS.

2. Connect the UPS Input socket to the AC line outlet through the Personal Computer supplying cable. t is

mandatory to ground the AC line outlet according to the Safety Standards. Carefully check the groun ing,

make sure that the utility power is available, an that its range falls within the UPS specifications (refer to

the “Specifications” chapter).

3. Press the ON/OFF button on the front panel: the UPS emits a brief acoustic signal, turns the le isplay on,

an performs a functioning SELF-TEST. After some secon s the UPS starts to work in Normal mode. Leave

the UPS in Normal mo e for at least 4 hours in or er to completely recharge the batteries.

4. Switch the UPS off (by pressing again the ON/OFF button).

5. Connect the evices to be supplie to the UPS outputs, by using only the inclu e cables. Be sure all the

evices have the main switch in ON position.

6. Turn on the UPS again. Check that it starts working correctly an it oesn’t signal any sort of anomaly.

Moreover be sure that all the evices connecte to the UPS outputs are working correctly.

7. Simulate a black-out by removing the AC Input line. The UPS starts working in Battery mode: the UPS emits a

brief acoustic signal every 10 secon s.

8. Be sure that all the evices connecte to the UPS outputs are working correctly an the UPS oesn’t signal

any sort of anomaly.

9. Restore the AC Input line: after few secon s the UPS turns back in Normal mo e.

Before using ERA LED normally, leave it in Normal mo e in or er to charge the batteries completely as specifie at

point 3. The batteries reach the 90% of their capacity after about 4 hours of recharge.

t is compulsory to ground/earth the UPS according to the Safety Standards.

Risk of electric shock at the Output lines if the UPS is ON, even when the UPS is not

connected to AC utility line.

Risk of electric shock at the Output lines while the unit is connected to the AC utility

line.

Risk of electric shock: do not remove the cover. The UPS contains internal parts, which

are at a high Voltage and are potentially dangerous, capable of causing injury or death

by electric shock.

There are no internal parts in the UPS that are user serviceable. Any repair or

maintenance work must be performed exclusively by qualified technical personnel

authorized by TECNOWARE. TECNOWARE declines any responsibility if this warning is

disregarded.

Disregard for these warnings may lead to a risk of electric shock to operators.

User’s manual 8 UPS ERA LED 0.65 – 0.85 – 1.1

6Functioning

6.1 Normal Mode

The UPS typically works in Normal mode: Input mains power is available an its amplitu e is within specifications.

In Normal mo e the L NE/BATTERY le is always on.

During Normal mo e, the UPS recharges the batteries an keeps them in an optimal charging voltage.

6.2 Battery Mode

The UPS automatically runs in Battery mode if the AC Input Line voltage amplitu e gets out of security limits (in

case of a black-out or over-voltage/low-voltage): in this case, the UPS supplies the require output power by its

internal battery an by the Inverter block.

The UPS automatically returns in Normal mo e a few secon s after the AC Input Line is recovere .

In Battery mo e the UPS emits an acoustic alarm signal every 10 secon s an simultaneously the L NE/BATTERY

le flashes.

6.3 Low Battery and Automatic Restart

In Battery mo e, ERA LED in icates the Low Battery con ition whenever the battery reaches a charge level

allowing connecte evices to operate for approximately one more minute.

During Low Battery con ition the UPS emits an acoustic alarm signal every secon an simultaneously the

L NE/BATTERY le flashes.

If AC Input oes not come back on within few minutes, the UPS shuts-down automatically thus preventing the

batteries from ischarging excessively; the UPS stops supplying Output power, eactivates control panel in ication

an goes to a waiting state. Once AC Input comes back on, the UPS restarts automatically an after some secon s

it goes back to work in Normal mo e.

After a complete ischarge, the UPS nee s 4 hours to recharge completely the batteries. The UPS recharges

batteries automatically if it works in Normal mo e or if it is off an connecte to the AC Input Line.

Inhaltsverzeichnis

Andere Tecnoware UPS Handbücher

Tecnoware

Tecnoware ERA PLUS 800 SCHUKO Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 Bedienungsanleitung

Tecnoware

Tecnoware UPS EVO DSP PLUS 1.0 MM Bedienungsanleitung

Tecnoware

Tecnoware EVO 3.0 RT Bedienungsanleitung

Tecnoware

Tecnoware EVO TM 15.0 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 8.0 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP TT Bedienungsanleitung

Tecnoware

Tecnoware EVO STAR Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP MM 4.0 Rack Tower Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS 1.200 PF 0.9 Bedienungsanleitung

Tecnoware

Tecnoware ERA PLUS 900 Bedienungsanleitung

Tecnoware

Tecnoware EXA LCD 2.6 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS TT 10.0 Bedienungsanleitung

Tecnoware

Tecnoware EVO 3.0 Bedienungsanleitung

Tecnoware

Tecnoware Ups Pro Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 1.0 - pf 0,9 Bedienungsanleitung

Tecnoware

Tecnoware EXA PLUS 1000 Bedienungsanleitung

Tecnoware

Tecnoware EXA 1.1 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP MM 6.0 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MODULAR Bedienungsanleitung

Tecnoware

Tecnoware ERA PLUS 600 Bedienungsanleitung

Tecnoware

Tecnoware EVO 3.0 RT Bedienungsanleitung

Tecnoware

Tecnoware ECO STRIP 0.50 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung

BPC

BPC 1.5K SMART Bedienungsanleitung