Tecnoware EVO TM 15.0 Bedienungsanleitung

EVO TM

Uninterruptible Power Supply

EVO TM 6.0 (6 KVA)

EVO TM 8.0 (8 KVA)

EVO TM 10.0 (10 KVA)

EVO TM 12.0 (12 KVA)

EVO TM 15.0 (15 KVA)

USER’S MANUAL

User’s manual 1 UPS EVO TM

TABLE OF CONTENTS

TABLE OF CONTENTS ......................................................................................................... 1

SAFETY WARNINGS ................................................................................................. 2

INTRODUCTION.......................................................................................................

GENERAL CHARACTERISTICS .................................................................................... 4

RECEIPT AND SITE SELECTION.................................................................................. 5

OPERATING MODES ................................................................................................. 5

EXTERNAL DESCRIPTION.......................................................................................... 7

ELECTRICAL INSTALLATION .....................................................................................11

FIRST START UP.....................................................................................................1

FUNCTIONING........................................................................................................14

10.

COMPUTER INTERFACE............................................................................................15

11.

TECHNICAL CHARACTERISTICS ................................................................................16

12.

RECOMMENDATIONS FOR CORRECT USE ...................................................................17

1 .

TROUBLESHOOTING ...............................................................................................19

14.

PICTURES..............................................................................................................21





All trademark are property of their respective owners.

TECNOWA E s.r.l.

www.service.tecnoware.com

This manual has been printed and edited by TECNOWA E s.r.l.

December 2007 Edition, version 4.0

UPS EVO TM 2 User’s manual

1. SAFETY WA NINGS

ead this manual carefully and completely before installing and using the

TECNOWA E EVO TM Uninterruptible Power Supply, which, from here after, will also

be referred to as UPS.

The UPS must be used only by properly trained personnel. To ensure correct and safe

operations, it is necessary that operators and maintenance personnel observe the

general safety Standards as well as the specific instructions included in this manual.

isk of electric shock: do not remove the cover. The UPS contains internal parts

which are at a high voltage and are potentially dangerous, capable of causing injury

or death by electric shock.

There are no internal parts in the UPS which are user serviceable. Any repair or

maintenance work must be performed exclusively by qualified technical personnel

authorized by TECNOWA E. TECNOWA E declines any responsibility if this warning is

disregarded.

The electric installation, has to be done by qualified personnel. Follow all the Safety

Standards (CEI Standards in Italy) for the IN/OUT connections and for the right

section of IN/OUT cables. We recommend to use a dedicated AC input/output power

Line for the UPS.

It is compulsory to ground the UPS according to safety Standards.

isk of electric shock at the output socket when the UPS is ON.

isk of electric shock at the output socket while the unit is connected to the AC utility

line.

For respect of the safety norms is necessary the presence of a differential switch

after of the UPS output.

We recommend to use a dedicate AC input/output power Line for the UPS.

Do not obstruct ventilation slots or holes and do not rest any object on top of the

UPS.

Do not insert objects or pour liquids in the ventilation holes.

Install the UPS indoors, in a protected, clean and moisture-free environment.

Do not expose to the direct sun light.

Do not keep liquids, flammable gases or corrosive substances near the UPS.

User’s manual 3 UPS EVO TM

2. INT ODUCTION

UPS EVO TM

The UPS EVO TM (Uninterruptible Power Supplies) are the result of constant technological

research aimed at obtaining the best performance at the lowest cost.

The EVO TM units are advanced ON-LINE UPS built specifically to protect your computer from

any irregularities in the AC line (for example blackouts, brownouts, over voltages, micro-

interruptions) which often cause damage to hardware and software.

All that is possible because EVO TM is a Double-Conversion ON-LINE UPS.

Under normal AC line condition UPS EVO TM provides an automatic output voltage regulation

from the Rectifier and Inverter blocks and filters out frequently occurring electrical

disturbances (high voltage transients, spikes, interferences, etc.), thus protecting the devices

connected to its outlets. During a power failure, UPS EVO TM continues supplying adequate AC

power (with a true sine wave) to all connected devices through its internal batteries and by its

DC/AC converter (Inverter).

UPS EVO TM protects the devices from accidental overload or Inverter fault by an AUTOMATIC

BYPASS that directly connects the AC input line with its outlets.

The EVO TM models are factory-equipped with a RS-2 2 interface which may be used for notify

to a computer a power failure or a low battery condition: this allows automatic data backup

during an extended blackout with the most common operating systems (Windows, Novell,

Linux, etc). Thanks to Interface RS2 2, UPS EVO TM can communicate the several made

measurements (input and output voltage, batteries, absorption, frequency…), and can also be

programmed in order to start-up or shutdown automatically at fixed times.

WA NING

ead this manual carefully before using an UPS EVO TM; it includes important safety

warnings and useful advices for correct use and installation.

EVO TM is constantly being developed and improved: consequently, your unit may differ

somewhat from the description contained in this manual.

This manual includes the follows models of the EVO TM series:

• EVO TM 10.0

• EVO TM 6.0 • EVO TM 12.0

• EVO TM 8.0 • EVO TM 15.0

In this manual, which covers all 5 models, EVO TM will simply be referred to as UPS.

UPS EVO TM 4 User’s manual

3. GENE AL CHA ACTE ISTICS

UPS EVO TM has all the modern features which guarantee maximum reliability and safety:

 Double-Conversion ON-LINE technology

 Sinusoidal wave generated by an IGBT INVERTER

 Output voltage regulation ±1%

 Protection from overload and short circuits

 Automatic BYPASS to protect from accidental overload or Inverter fault

 Start-up even under MAINS OFF conditions

 Automatic protection when battery is low

 Automatic restart, following an automatic shut-down due to low battery, once AC

utility power comes back on.

 Selectable input frequency (50/60 Hz)

 Display LCD for visualization of the input and output voltage measurements,

batteries voltage, percentage of power used, percentage of load, frequency and

operating temperature.

 Visual warnings through led, indicating low battery, overload and fault conditions

 Dry Contact board (optional)

 SNMP Adapter (optional)

 EPO (Emergency Power OFF)

 Remote ON/OFF

 Acoustic signals of various kinds indicating alarm situations

 Communication with the computer through RS-2 2

 Available extended autonomy by adding external Battery Boxes

 High efficiency

 Maximum reliability

 Smart design and easy to use.

User’s manual 5 UPS EVO TM

4. ECEIPT AND SITE SELECTION

Carefully remove the UPS from its packaging, and carry out a meticulous inspection. We

recommend keeping the original packaging in case you need to send the UPS for maintenance

purposes. In case of transport damage, notify the carrier and dealer immediately. We

recommend keeping the original packaging in a secure place, in case you need to ship the UPS

for maintenance purposes.

We recommend to pay attention to the below points in order to choose a correct placement for

your UPS:

• The UPS is designed to operate in a protected environment (e.g. offices). We therefore

recommend installing it in a place with very little or no humidity, dust or smoke.

• In all circumstances, see the TECHNICAL CHARACTERISTICS chapter for environmental

specifications and check that the selected area meets these criteria.

• During normal operation UPS EVO TM discharges a minimal amount of heat. So it is

necessary to leave at least 10 cm of unobstructed space all around the UPS in order to

keep it properly ventilated.

• Do not obstruct ventilation holes.

• Do not insert objects or pour liquids in the ventilation holes.

• Do not rest any object on top of the UPS.

• Do not keep liquids, flammable gases or corrosive substances near the unit.

• Install UPS EVO TM on a properly tiled floor. Avoid the installation on a floor that is not

tiled flat.

5. OPE ATING MODES

The operation modes are: LINE MODE, BATTERIES mode and BYPASS mode.

For details see figure 1.

LINE MODE

UPS EVO TM typically works in LINE mode, input mains power is available and its amplitude is

within specifications.

After the filter has eliminated any high frequency interferences present on the mains, the input

line Is rectified and conditioned in the RECTIFIER board (AC/DC conversion); the continuous

power now enters into the INVERTER board and is then reconverted in alternated power

(DC/AC conversion), overcoming the AUTOMATIC BYPASS and feeding the load after an extra

filtration. At the same time UPS EVO TM recharges the batteries through the BATTERY

CHARGER block. Please refer to figures 2A/2B, that describes the UPS front panel, the LINE

MODE is identified by:

• Led LINE and UPS are on

UPS EVO TM 6 User’s manual

BATTE Y MODE

During operation in the LINE MODE, if the UPS finds the MAINS OFF condition (due to a

blackout or overvoltage/brownout), it then switches into BATTERY mode. In this case, the

batteries supplies the required output power thanks to the DC/AC conversion carried out by

the INVERTER. UPS EVO TM switches back to LINE MODE a few seconds after AC input power

is restored or voltage comes back to internal specifications.

The BATTERY mode is identified by:

• Led LINE off and led UPS on.

• The UPS emits an acoustic signal approximately every 2 seconds, in order to indicate

the BATTERY MODE

The acoustic signal will be automatically de-activated after 90 seconds.

BYPASS MODE

In BYPASS mode, the AC input line is directly connected with the UPS outlets by an

AUTOMATIC BYPASS.

As it is indicated in figure 1, in BYPASS mode the UPS recharge however the batteries.

UPS EVO TM uses the BYPASS mode during the start-up phase; furthermore the UPS

switches automatically to BYPASS mode as a consequence of accidental overload or

Inverter fault thus protecting the supplied devices.

The BYPASS mode is identified by:

• BYPASS Led and LINE led are lit.

When EVO TM functions in BYPASS mode it can be considered as “not active”, since the

INVERTER block is not active.

EVO TM is considered “active” when the INVERTER block is on (LINE mode and BATTERY

mode).

To activate or de-activate UPS EVO TM use the INV ON/OFF button on the front panel.

WA NING

When UPS EVO TM works in BYPASS mode there isn’t output power if the input

power is OFF.

User’s manual 7 UPS EVO TM

6. EXTE NAL DESC IPTION

F ONT PANEL

On the front panel there is an LCD display, buttons and some led which indicate the various

operating and alarm conditions. Please refer to figure 1, describing the UPS several operation

modes (LINE MODE, BATTERY mode and BYPASS mode) and to the figures 2A/2B we give a

short description of the frontal panel elements.

LCD Display

At the top of the frontal panel is present a two rows LCD display showing the UPS functioning

state and the UPS measurements values. After approximately 2 minutes without pressing any

of the frontal panel buttons the display back-lighting turns off. To relight it press SELECTION

button.

ON Button

By pressing the “ON” button the inverter is activated and will supply the output power within

20 second.

OFF Button

By pressing the “OFF” button for approximately seconds the inverter is deactivated and the

UPS switches in BYPASS mode.

SELECTION Button

Using the button, represented by two vertical arrows, is possible to change the slide visualized

on the LCD display. Every time the button is pressed the slide changes in according to the

sequence described in Table 1 (the display shows the actual screen number visualized by a

fractional number 2/8, 5/8, etc).

Table 1: Indications of LCD display LCD

Display show

Description

TECNOWA E

EVO TM XXX

Welcome message

STATUS

AC:IN BAT:OK

State of the system (*refer following note)

INPUT VOLTAGE

220 V 2/8

INPUT VOLTAGE

OUTPUT VOLTAGE

220 V 3/8

OUTPUT VOLTAGE

INPUT F EQUENCY

50 HZ 4/8

INPUT FREQUENCY

OUTPUT F EQUENCY

50 HZ 5/8

OUTPUT FREQUENCY

BATTE Y VOLTAGE

220V 6/8

BATTERY VOLTAGE

CU ENT LOAD

100% 7/8

CURRENT LOAD (%)

TEMPE ATU E

33° 8/8

INTERNAL TEMPERATURE

UPS EVO TM 8 User’s manual

*AC and BAT refer respective to the mains voltage and to the battery, in particular:

AC:IN

Normal mains voltage

AC:LOSS

Anomalous mains voltage

BAT:OK

Normal Battery autonomy

BAT:LOW

Low Battery autonomy

Table 2: led present on the frontal panel

Indication on the panel Description

LINE

This led indicates the presence of the input mains voltage is within specifications.

UPS

This led indicates that the inverter is active and supplies the output.

BY-PASS

This led indicates that the UPS is in BYPASS mode and therefore the inverter is

not active.

FAULT

This led indicates the THERMAL PROTECTION FOR OVERLOAD conditions or for

the INVERTER FAULT.

BATTE Y LOW

It indicates when the level of the battery is low.

OVE LOAD

Overload indication.

EA SIDE

To view the rear side of UPS EVO TM (see figure 4):

1. Main switch (ON/OFF): is the general switch of the UPS; in the OFF position it interrupts

the input power line and the battery circuit (see figure 4).

WA NING

UPS EVO TM is completely inactive only if the main switch is in the OFF position (see

figure 4).

If instead the switch is in the ON position, UPS EVO TM is active and voltage is

present in the output.

2. Computer Interface (connector female 9 poles DB9): it is the communication port

RS-2 2.

3. Metallic panel for access to the input/output terminal board: by removing it and

unscrewing related screws, it is possible to access to the input/output terminal board (see

figure ).

4. Slot for Dry contact board (optional)/Slot for SNMP adapter (optional).

5. Manual BYPASS switch: to force the UPS into BYPASS mode (see chapter “Running

Operations”).

6. emote ON/OFF connector.

7. EPO (Emergency Power OFF) connector.

Inhaltsverzeichnis

Andere Tecnoware UPS Handbücher

Tecnoware

Tecnoware EVO STAR Bedienungsanleitung

Tecnoware

Tecnoware ERA PLUS 600 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS 800 PF 0.9 Bedienungsanleitung

Tecnoware

Tecnoware EXA 2.6 Bedienungsanleitung

Tecnoware

Tecnoware ERA PLUS 900 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 8.0 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP TM Bedienungsanleitung

Tecnoware

Tecnoware ECO STRIP 0.50 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS 1.200 Rack Tower PF 0.9 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP MM 6.0 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS TM 10 KVA Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS 1.200 PF 0.9 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MODULAR Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS TT 10.0 Bedienungsanleitung

Tecnoware

Tecnoware EVO 3.0 RT Bedienungsanleitung

Tecnoware

Tecnoware UPS EVO DSP PLUS 6.5 PF 0,9 Bedienungsanleitung

Tecnoware

Tecnoware ATA 4.0 MM Bedienungsanleitung

Tecnoware

Tecnoware Ups Pro Bedienungsanleitung

Tecnoware

Tecnoware ERA PLUS 800 SCHUKO Bedienungsanleitung

Tecnoware

Tecnoware EXA PLUS 1000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 1.2 Bedienungsanleitung

Tecnoware

Tecnoware EXA PLUS 1.0 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP TT Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung

BPC

BPC 1.5K SMART Bedienungsanleitung