TECOM WL5030 Bedienungsanleitung
WL5030
WLAN Access Point
User’s Manual
Version 1.0
TECOM CO., LTD.
March 2003
©2003 by TECOM CO., LTD.
All rights reserved.
Printed in Taiwan
1
Table of Contents
Package Contents and Trademark(s)- ------------- 2
Software Installation ---------------------------------- 3
Utilities Using Guide -----------------------------------4
Configuration for Optional function----------------7
Point-to-Point Wireless Bridge-----------------------8
Point-to-Multipoint Wireless Bridge----------------9
Troubleshooting --------------------------------------11
Specifications ------------------------------------------ 13
Technical Support ------------------------------------ 13
2
Package Contents
The package you have received should contain the
following items:
Wireless LANAccess Point
CD ROM containing Utility Software and
User’s Manual
Quick Installation Guide
Trademark(s)TM and Registered Trademark(s)®
TECOM and the TECOM logo are trademarks of
TECOM CO., LTD.
Microsoft, Windows are registered trademarks of
Microsoft Corporation. Other brand and product names
may be registered trademarks or trademarks of their
respective holders.
3
Software Installation Guide
For AP Configuration
1. Run the “Setup.exe” in the folder of AP Configuration of the
driver disk. Follow the guideline on the screen, and select
the directory where the application will be installed, it will
deploy all files that needed at that. At the end, windows will
show a message that installation is completed.
2. Power on the Access point.
3. Plug the “cross over” type Ethernet cord into both port of
host PC and AP. (If you don’t have “cross over” type
Ethernet cord and have a hub, then you can use normal type
Ethernet cable to connect both host PC and AP to hub.)
4. You can run the program of “AP Configuration”, which you
can find in “start” ”program” ”TECOM”
”SNMPManager”
5. Make sure that the IP address of your host PC and AP are in
the same sub-net, because this program is based on SNMP.
The default setting of IP address of AP is 10.170.254.37
4
Utilities Using Guide
For AP Configuration
When you run the AP Configuration, you will see a dialog box pop
up like below. Of course, the AP is already connected to your host
PC by Ethernet port.
1. Press “File””Find Access Point”, it will show a dialog box
like below to show you how many Access Points it found on
the net.
5
2. Choose the one you want to configure and press “Connect”,
it shows another dialog box like below. Enter your
community and choose your Authority. (The default settings
of community are all “public”.) Press “OK”, After then, if
both of you are in the same sub-net, it will get the Access
point you choose, and turn into a configuration dialog box.
3. Press “Setup” ”Bridge” ”IP Configuration”, a Bridge IP
Configuration dialog box will pop up. Here, you can set the
IP address and IP mask.
6
4. Press “Setup” ”Wireless LAN” ”Operational Settings”,
a Wireless Operational Settings dialog box will pop up. Here,
you can set the ESSID and the channel you want.
5. Press “File” ”Download Changes” to make all you change
download to AP.
After done the above setting, the AP should work properly.
7
Configuration for Optional function ---Wireless Bridge
Wireless Bridge function is somewhat like a repeater in the
Ethernet world. It can make 2 remote Ethernet LANs just like to be
one, which both LANs must got an individual AP connected with.
(in another word, 2 remote Ethernet LANs can connected with
each other by APs working under the mode.) There are 2 type of
bridge mode, point-to-point and point-to-multipoint. You can see
from below.
8
Point-to-Point Wireless Bridge: This mode allows one wireless
bridge communicate with a specific remote one only.
1. Run the “AP Configuration” and make a connection with
your AP.
2. Press “Advanced” button in the right lower Conner of
“Setup” ”Wireless LAN” ”Operational Settings”, then
you will see a pop-up dialog like this.
3. click on “Point to Point” and fill in the remote MAC address
of the other side of AP in this field.
4. Press “File” ”Download Changes” to make all you change
download to AP.
5. On the other side, do as the same, but only the field of
“Remote MACAddress” is that of this side of AP.
9
6. Make both APs working on the same channel, then you
should have an wireless bridge working now.
Point-to-Multipoint Wireless Bridge: This mode allows
wireless bridge communicate with any bridge on the same
channel.
1. Like in “Point-to-Point” mode, just clicks on
“Point-to-MultiPoint”, do the same step to all AP you want
to work in bridge mode.
2. Make sure that all bridge mode AP on the same channel.
Then you can connect with each other.
If you want to allow only AP with authentication to connect,
then you can start up authorization algorithm.
1. Make an authorized MAC list---just put all the MAC address
of AP you want to connect in a text file. For example, if you
want AP which MAC address is 00-00-22-22-22-50 in your
MAC list, then you just put “000022222250” in your list file.
2. Run “AP Configuration”. Clicks on “Setup” ”Wireless
LAN” ”Authorized Mac Addresses”, you will see a
pop-up dialog box as below, except the content is blank.
Inhaltsverzeichnis
Andere TECOM Drahtloser Zugangspunkt Handbücher
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Cisco
Cisco Aironet 1550 Series Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
EnGenius
EnGenius EnStationACv2 Bedienungsanleitung
D-Link
D-Link DAP-3662 Bedienungsanleitung
xG Technology
xG Technology xMax CN1300 Bedienungsanleitung
Widelink
Widelink ezWave WAP-1100 Series Bedienungsanleitung
Edimax
Edimax CAP1200 Bedienungsanleitung
