Teeggi SG906 Bedienungsanleitung
SG906
Brushless Motor
(1806 1500KV)
Independent ESC
(Card protection, high
temperature protection)
Two-way 2.4GHz
(remote signal weak signal
alarm, low pressure alarm)
4K Full HD Image transmission200-300M
Farther. Faster. Clearer
(Please confirm that the mobile phone used supports 5G WiFi standard)
GPS system
4K 5G WIFI
camera
Gesture recordingGesture photo
Gesture control
One-button return
Trajectory flight
Follow the flight
User manual
Important statement
● This product is not a toy, but a precision device that
integrates expertise in mechanics, electronics,
aerodynamics, and high-frequency emission. It
requires proper assembly and commissioning to
avoid accidents. The holder of the product must use
a safe means of operation control; improper handling
may result in serious personal injury or property
damage.
● This product is suitable for people who have
experience in operating model aircraft and are not
younger than 14 years old.
● In case of use, operation, maintenance, etc., please
contact your local dealer or the relevant personnel of
the company. We and the seller are not responsible
for any loss or damage caused by improper use or
operation and human injury.
● The product contains small parts, so keep them out
of reach of children to avoid the risk of eating or
suffocating.
Safety Precautions
The remote-controlled model aircraft is the most
dangerous commodity, so be sure to stay away from
the crowd when flying.Improper assembly or damage
to the body, poor electronic control, and unfamiliar
operation can lead to unpredictable accidents such as
aircraft damage or personal injury.
Important statement and safety guidelines
You are welcome to purchase our products. In order
to make it easier and more convenient for you to use
this aircraft, please read this manual and then operate
it. Please save this manual as well.
After adjustment and maintenance reference.
-1-
● Stay away from obstacles and people
The remotely piloted aircraft has an indeterminate flight speed
and state when flying, and is potentially dangerous. When
flying, you must stay away from people, high-rise buildings,
high-voltage power lines, etc., while avoiding flying in bad
weather such as wind and rain and lightning. Commissioning
and installing the aircraft must be carried out in strict
accordance with the operating instructions. Note that the
aircraft should be kept at a distance of 1-2 meters from the
user or other people during flight, to avoid the aircraft flying,
landing, hitting the head, face and body, causing injury.
● Keep away from the humid environment
The interior of the aircraft is composed of many sophisticated
electronic components and mechanical parts. Therefore, it is
necessary to prevent the aircraft from getting wet or moisture
into the body, so as to avoid accidents caused by mechanical
and electronic components failure. Use a clean rag to clean
the surface stains during maintenance.
● Avoid manipulation alone
The remote control aircraft control technique has certain
difficulties in the early stage of learning. It is necessary to
avoid flying by itself, and it should be guided by experienced
people.
● Proper use of this product
Please use our original parts for modification or repair to
ensure flight safety. Please operate and use within the scope
of the product's functions and may not be used for other illegal
purposes other than the safety laws.
●Safe operation
1. Operate the remote control aircraft according to your own
status and flight skills. Fatigue, poor mental health or
improper operation will increase the probability of
unexpected risks.
2. Do not use near the ear! Misuse can cause hearing damage.
-2-
Please operate the flight crew to pay attention to flight
safety, you must understand the responsibility of
accidents caused by your negligence.
Product Description
Product Configuration
Packing List
Basic Parameters
Wheelbase: 340mm Total weight: about 530g
Brushless motor: 1806 1500KV
Battery: 7.4V 2800mAh 25C
Charging time: about 6 hours
Flight time: about 23 minutes
Aircraft fuselage X1 Charging cable X1
Screwdriver X1 Remote control X1
USB charging cable X1 Battery X1
positive / reverse wind blade X1 (sold separately)
● Keep away from high speed rotating parts
When the rotor of the aircraft is rotating at high speed, please
keep the pilot, the surrounding crowd and objects away from
the rotating parts to avoid danger and damage.
● Keep away from heat
The remote control aircraft is made of metal, fiber, plastic,
electronic components and other materials, so it should be
kept away from heat sources, prevent sun exposure, and
avoid deformation or even damage caused by high
temperature.
● Environmental requirements
Discarding this product at will may affect the environment.
Please dispose of it properly in accordance with local laws
and regulations.
-3-
Aircraft Component
1
2
3
4
5
1.Propeller Installation
Make sure all propellers are installed in the correct orientation
as shown below. If the installation is wrong, the aircraft will not
be able to fly normally.
A
B
B
A
1.HD camera
2. Propeller
3. Motor
4. LED lights
5. Smart lithium battery
-4-
1
2
3
!Tips: If the battery is not installed properly, it is likely to
cause the drone to interrupt the electric fall accident.
Battery Installation
- Press and hold the power button for 3 seconds to turn it on,
then press and hold the power button for 3 seconds to turn it
off.
- Once the battery is in a low battery state, there is one light left
in the battery power indicator. Please charge the battery
immediately to avoid unnecessary loss.
Press the battery button down and push the battery into the
battery compartment of the drone. After the installation is
complete, the battery clip will pop up and check to make sure
the battery is in place.
2. Aircraft Lithium Battery
1.Battery switch
2.Battery level indicator
3.USB interface
low Electricity high
-5-
USB charging
cable
battery
Aircraft Battery Charging
Connect the battery to the 5V 1-2A adapter USB port with a USB
charging cable. Connect the battery to charge it. When the
battery is charging, the battery blue light flashes from left to right,
and the battery power indicator is always on after the battery is
fully charged. The battery is fully charged for approximately 6
hours.
Battery Removal
Press the battery clip, then place the finger on the specified
position and pull it back. The battery will be removed
immediately. Keep the finger and the machine clean and dry
before operation. Otherwise, the battery may not be slipped.
USB
!
Tips:
● Please insert the plug in the correct way.
● It is recommended to use the 5V 1-2A adapter for
charging.
adapter
(sold
separately)
-6-
● When charging the rechargeable battery, do not use it
separately for children. It must be carried out under
adult supervision. It must be kept away from
inflammable materials during charging. When charging,
the guardian should not leave the model to the outside
of the surveillance range.
● Please do not short circuit or squeeze the battery to
avoid explosion.
● The power terminals should not be removed from the
model, the terminals should not be short-circuited; do
not short-circuit, disassemble or put the battery into fire;
do not place the battery in a hot, heated place (such as
in a fire or near a heating device).
● The model can only use the recommended charger.
The charger is not a model. The model that can be
cleaned with liquid should be disconnected from the
charger before cleaning. Check the charger's wires,
plugs, casing and other components regularly for
damage. Stop using the battery if it is damaged. Until
the repair is in order.
● The charger is not a toy; the charger can only be used
indoors.
● The battery after the flight needs to be recharged and
stored. If it is not used, it is recommended to charge the
battery at least once every 3 months to prevent the
battery from being over-discharged and permanently
damaging the battery.
!
Camera Installation/removal
Camera Installation:
Insert the camera into the aircraft as shown in the figure (see
Figure 1) and pay attention to the buckle (Figure 2).
figure 1 figure 2
-7-
PTZ camera control
By dialing the remote control PTZ button, you can adjust the
shooting angle of the PTZ camera and experience a better
aerial photography process. When the left button is pressed, the
camera is adjusted in the A direction; when the right button is
pressed, the camera is adjusted in the B direction.
Camera Removal:
Hold your finger on the camera snap and press the arrow
(Figure 1) to remove the camera. (Figure 2)
!Tips: The camera needs to be used with the real-time
transmission app. For details on the download process,
please refer to the APP manual. For details on the
camera function, please refer to the contents of the app.
figure 1 figure 2
A
B
AB
-8-
[6] Battery compartment
[7] Front indicator
[8] Rear indicator
Aircraft Part Name
[1] Lights [2] Brushless Motors
[3] Blades [4] Cameras
[6]
[8]
[7]
[1]
[2]
[3]
[4]
-9-
Inhaltsverzeichnis
