Tektronix MSO 4 Series Benutzerhandbuch
4 Series MSO
MSO44, MSO46
Installation and Safety
www.tek.com
071-3644-00
Supports 4 Series MSO Product Firmware V1.18.XX and above.
ООО "Техэнком" Контрольно-измерительные приборы и оборудование www.tehencom.com
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are
protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued
and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges
reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
■In North America, call 1-800-833-9200.
■Worldwide, visit www.tek.com to find contacts in your area.
ООО "Техэнком" Контрольно-измерительные приборы и оборудование www.tehencom.com
Warranty
Tektronix warrants that this product will be free from defects in materials and workmanship for a period of three (3) years from the date of
shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product
without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement
products used by Tektronix for warranty work may be new or reconditioned to like new performance. All replaced parts, modules and
products become the property of Tektronix.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period and
make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective
product to the service center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to
Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall be responsible
for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care.
Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts by personnel other than
Tektronix representatives to install, repair or service the product; b) to repair damage resulting from improper use or connection to
incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product
that has been modified or integrated with other products when the effect of such modification or integration increases the time or difficulty
of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS
OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. TEKTRONIX' RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL
NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER
TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
[W4 – 15AUG04]
ООО "Техэнком" Контрольно-измерительные приборы и оборудование www.tehencom.com
ООО "Техэнком" Контрольно-измерительные приборы и оборудование www.tehencom.com
Table of Contents
Important safety information ................................................................................................................................ iii
General safety summary ................................................................................................................................ iii
Service safety summary ................................................................................................................................. v
Terms in the manual ...................................................................................................................................... vi
Terms on the product .................................................................................................................................... vi
Symbols on the product ................................................................................................................................. vi
Preface ............................................................................................................................................................... vii
Key features .................................................................................................................................................. vii
Related documents ...................................................................................................................................... viii
Installing your instrument
Check shipped accessories ........................................................................................................................... 1
Safely rotate the handle ................................................................................................................................. 1
Operating requirements ................................................................................................................................. 2
Input signal requirements ............................................................................................................................... 3
Secure (lock) the oscilloscope ....................................................................................................................... 3
Powering the oscilloscope .............................................................................................................................. 4
Check that oscilloscope passes power-on self tests ...................................................................................... 5
Connecting Probes ......................................................................................................................................... 5
Rackmount option information ....................................................................................................................... 6
Getting acquainted with your instrument
Front panel controls and connectors .............................................................................................................. 7
Rear panel connections ............................................................................................................................... 14
The user interface screen ............................................................................................................................ 15
The user interface elements ......................................................................................................................... 16
Badges ......................................................................................................................................................... 20
Configuration menus .................................................................................................................................... 26
The Zoom user interface elements .............................................................................................................. 27
Using the touch screen interface for common tasks .................................................................................... 28
Configure the instrument
Set the time zone and clock readout format ................................................................................................. 31
Download and install the latest 4 Series MSO firmware .............................................................................. 31
Run Signal Path Compensation (SPC) ........................................................................................................ 32
MSO44, MSO46 Installation and Safety Manual i
ООО "Техэнком" Контрольно-измерительные приборы и оборудование www.tehencom.com
Compensate the TPP Series probes ............................................................................................................ 32
Connect to a network (LAN) ......................................................................................................................... 34
Cleaning ....................................................................................................................................................... 34
Operating basics
Add a channel waveform to the display ....................................................................................................... 35
Configure channel or waveform settings ...................................................................................................... 36
Quickly display a waveform (Autoset) .......................................................................................................... 37
How to trigger on a signal ............................................................................................................................ 38
Set the acquisition mode .............................................................................................................................. 39
Set Horizontal parameters ........................................................................................................................... 40
Add a math, reference, or bus waveform ..................................................................................................... 40
Add a measurement ..................................................................................................................................... 42
Configure a measurement ............................................................................................................................ 44
Add a plot of a measurement ....................................................................................................................... 45
Add a Search ............................................................................................................................................... 47
Delete a Measurement or Search badge ..................................................................................................... 48
Change waveform view settings .................................................................................................................. 49
Display and configure cursors ...................................................................................................................... 49
Connect the oscilloscope to a PC using a USB cable .................................................................................. 51
See Help for information on other operations .............................................................................................. 51
EMC, safety and environmental compliance
Compliance Information ............................................................................................................................... 53
EMC compliance .................................................................................................................................... 53
Safety compliance .................................................................................................................................. 54
Environmental compliance ..................................................................................................................... 55
Table of Contents
ii MSO44, MSO46 Installation and Safety Manual
ООО "Техэнком" Контрольно-измерительные приборы и оборудование www.tehencom.com
Important safety information
Safety information provides warnings and cautions that help you operate the instrument safely and keep the instrument in a safe
working condition.
This manual contains information and warnings that must be followed by the user for safe operation and to keep the product in a
safe condition.
To safely perform service on this product, see the Service safety summary that follows the General safety summary.
General safety summary
Use the product only as specified. Review the following safety precautions to avoid injury and prevent damage to this product or
any products connected to it. Carefully read all instructions. Retain these instructions for future reference.
This product shall be used in accordance with local and national codes.
For correct and safe operation of the product, it is essential that you follow generally accepted safety procedures in addition to
the safety precautions specified in this manual.
The product is designed to be used by trained personnel only.
Only qualified personnel who are aware of the hazards involved should remove the cover for repair, maintenance, or adjustment.
Before use, always check the product with a known source to be sure it is operating correctly.
This product is not intended for detection of hazardous voltages.
Use personal protective equipment to prevent shock and arc blast injury where hazardous live conductors are exposed.
While using this product, you may need to access other parts of a larger system. Read the safety sections of the other
component manuals for warnings and cautions related to operating the system.
When incorporating this equipment into a system, the safety of that system is the responsibility of the assembler of the system.
To avoid fire or personal injury
Use proper power cord. Use only the power cord specified for this product and certified for the country of use. Do not use the
provided power cord for other products.
Ground the product. This product is grounded through the grounding conductor of the power cord. To avoid electric shock, the
grounding conductor must be connected to earth ground. Before making connections to the input or output terminals of the
product, ensure that the product is properly grounded. Do not disable the power cord grounding connection.
Power disconnect. The power cord disconnects the product from the power source. See instructions for the location. Do not
position the equipment so that it is difficult to operate the power cord; it must remain accessible to the user at all times to allow for
quick disconnection if needed.
Connect and disconnect properly. Do not connect or disconnect probes or test leads while they are connected to a voltage
source. Use only insulated voltage probes, test leads, and adapters supplied with the product, or indicated by Tektronix to be
suitable for the product.
Observe all terminal ratings. To avoid fire or shock hazard, observe all rating and markings on the product. Consult the product
manual for further ratings information before making connections to the product. Do not exceed the Measurement Category
(CAT) rating and voltage or current rating of the lowest rated individual component of a product, probe, or accessory. Use caution
when using 1:1 test leads because the probe tip voltage is directly transmitted to the product.
Do not apply a potential to any terminal, including the common terminal, that exceeds the maximum rating of that terminal.
Do not float the common terminal above the rated voltage for that terminal.
MSO44, MSO46 Installation and Safety Manual iii
ООО "Техэнком" Контрольно-измерительные приборы и оборудование www.tehencom.com
The measuring terminals on this product are not rated for connection to Category III or IV circuits.
Do not operate without covers. Do not operate this product with covers or panels removed, or with the case open. Hazardous
voltage exposure is possible.
Avoid exposed circuitry. Do not touch exposed connections and components when power is present.
Do not operate with suspected failures. If you suspect that there is damage to this product, have it inspected by qualified
service personnel.
Disable the product if it is damaged. Do not use the product if it is damaged or operates incorrectly. If in doubt about safety of the
product, turn it off and disconnect the power cord. Clearly mark the product to prevent its further operation.
Before use, inspect voltage probes, test leads, and accessories for mechanical damage and replace when damaged. Do not use
probes or test leads if they are damaged, if there is exposed metal, or if a wear indicator shows.
Examine the exterior of the product before you use it. Look for cracks or missing pieces.
Use only specified replacement parts.
Do not operate in wet/damp conditions. Be aware that condensation may occur if a unit is moved from a cold to a warm
environment.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry. Remove the input signals before you clean the product.
Provide proper ventilation. Refer to the installation instructions in the manual for details on installing the product so it has
proper ventilation.
Slots and openings are provided for ventilation and should never be covered or otherwise obstructed. Do not push objects into
any of the openings.
Provide a safe working environment. Always place the product in a location convenient for viewing the display and indicators.
Avoid improper or prolonged use of keyboards, pointers, and button pads. Improper or prolonged keyboard or pointer use may
result in serious injury.
Be sure your work area meets applicable ergonomic standards. Consult with an ergonomics professional to avoid stress injuries.
Use care when lifting and carrying the product. This product is provided with a handle for lifting and carrying.
Use only the Tektronix rackmount hardware specified for this product.
Probes and test leads
Before connecting probes or test leads, connect the power cord from the power connector to a properly grounded power outlet.
Keep fingers behind the protective barrier, protective finger guard, or tactile indicator on the probes.
Remove all probes, test leads and accessories that are not in use.
Use only correct Measurement Category (CAT), voltage, temperature, altitude, and amperage rated probes, test leads, and
adapters for any measurement.
Important safety information
iv MSO44, MSO46 Installation and Safety Manual
ООО "Техэнком" Контрольно-измерительные приборы и оборудование www.tehencom.com
Beware of high voltages. Understand the voltage ratings for the probe you are using and do not exceed those ratings. Two
ratings are important to know and understand:
■The maximum measurement voltage from the probe tip to the probe reference lead
■The maximum floating voltage from the probe reference lead to earth ground
These two voltage ratings depend on the probe and your application. Refer to the Specifications section of the manual for more
information.
WARNING. To prevent electrical shock, do not exceed the maximum measurement or maximum floating voltage for the
oscilloscope input BNC connector, probe tip, or probe reference lead.
Connect and disconnect properly. Connect the probe output to the measurement product before connecting the probe to the
circuit under test. Connect the probe reference lead to the circuit under test before connecting the probe input. Disconnect the
probe input and the probe reference lead from the circuit under test before disconnecting the probe from the measurement
product.
Connect and disconnect properly. De-energize the circuit under test before connecting or disconnecting the current probe.
Connect the probe reference lead to earth ground only.
Do not connect a current probe to any wire that carries voltages or frequencies above the current probe voltage rating.
Inspect the probe and accessories. Before each use, inspect probe and accessories for damage (cuts, tears, or defects in the
probe body, accessories, or cable jacket). Do not use if damaged.
Service safety summary
The Service safety summary section contains additional information required to safely perform service on the product. Only
qualified personnel should perform service procedures. Read this Service safety summary and the General safety summary
before performing any service procedures.
To avoid electric shock. Do not touch exposed connections.
Do not service alone. Do not perform internal service or adjustments of this product unless another person capable of rendering
first aid and resuscitation is present.
Disconnect power. To avoid electric shock, switch off the product power and disconnect the power cord from the mains power
before removing any covers or panels, or opening the case for servicing.
Use care when servicing with power on. Dangerous voltages or currents may exist in this product. Disconnect power, remove
battery (if applicable), and disconnect test leads before removing protective panels, soldering, or replacing components.
Verify safety after repair. Always recheck ground continuity and mains dielectric strength after performing a repair.
Important safety information
MSO44, MSO46 Installation and Safety Manual v
ООО "Техэнком" Контрольно-измерительные приборы и оборудование www.tehencom.com
Terms in the manual
These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.
Terms on the product
These terms may appear on the product:
■DANGER indicates an injury hazard immediately accessible as you read the marking.
■WARNING indicates an injury hazard not immediately accessible as you read the marking.
■CAUTION indicates a hazard to property including the product.
Symbols on the product
When this symbol is marked on the product, be sure to consult the manual to find out the nature of the potential
hazards and any actions which have to be taken to avoid them. (This symbol may also be used to refer the user to
ratings in the manual.)
The following symbols may appear on the product:
Important safety information
vi MSO44, MSO46 Installation and Safety Manual
ООО "Техэнком" Контрольно-измерительные приборы и оборудование www.tehencom.com
Andere Handbücher für MSO 4 Series
3
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Tektronix Prüfgeräte Handbücher
Tektronix
Tektronix MTS400 Series Bedienungsanleitung
Tektronix
Tektronix MSO2000 Series Bedienungsanleitung
Tektronix
Tektronix TDS3012B Bedienungsanleitung
Tektronix
Tektronix 7B52 Bedienungsanleitung
Tektronix
Tektronix 214 Bedienungsanleitung
Tektronix
Tektronix CSA 907A Bedienungsanleitung
Tektronix
Tektronix MSO46B Montage- und Wartungsanleitung
Tektronix
Tektronix TDS1000B Series Bedienungsanleitung
Tektronix
Tektronix P6247 Bedienungsanleitung
Tektronix
Tektronix TDS 410A Gebrauchs- und Pflegehandbuch
Tektronix
Tektronix MSO6 B Series Benutzerhandbuch
Tektronix
Tektronix DF2 Bedienungsanleitung
Tektronix
Tektronix TDS3000 Series Fehlerbehebungshandbuch
Tektronix
Tektronix P6960 Bedienungsanleitung
Tektronix
Tektronix 442 Bedienungsanleitung
Tektronix
Tektronix P6042 PROBE Bedienungsanleitung
Tektronix
Tektronix DPO70000SX Series Bedienungsanleitung
Tektronix
Tektronix 2445 Bedienungsanleitung
Tektronix
Tektronix TDS 340A Bedienungsanleitung
Tektronix
Tektronix 2465A Bedienungsanleitung
Beliebte Prüfgeräte Handbücher anderer Marken
SMART
SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies BERT Serial Bedienungsanleitung
Agilent Technologies
Agilent Technologies N3280A Bedienungsanleitung
Vernier
Vernier Go Direct Voltage Bedienungsanleitung
Lifeloc
Lifeloc R.A.D.A.R. Bedienungsanleitung
Fluke
Fluke T5-600 Bedienungs- und Montageanleitung
PCB Piezotronics
PCB Piezotronics 8159-0112A Bedienungsanleitung
BW Technologies
BW Technologies MicroDock II Bedienungsanleitung
Sun Nuclear
Sun Nuclear 1027 Bedienungsanleitung
Biomark
Biomark HPR LITE READER Bedienungsanleitung
Hioki
Hioki 3169-20 Bedienungsanleitung
Ashcroft
Ashcroft ATE-100 Bedienungsanleitung