Tektronix P6101B Bedienungsanleitung

Instructions

P6101B

15 MHz 1X Passive Probe

070-7819-07

Tektronix products are covered by U.S. and foreign patents, issued and

pending. Information in this publication supercedes that in all previously

published material. Specifications and price change privileges reserved.

Printed in the U.S.A.

Tektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

P6101B Instructions 1

General Safety Summary

Review the following safety precautions to avoid injury and prevent

damage to this product or any products connected to it. To avoid

potential hazards, use this product only as specified.

To Avoid Fire or Personal Injury

Observe Maximum Working Voltage. Do not use the P6101B probe

above 300 VRMS, CAT II. Refer to the derating chart, Figure 1, on

page 7.

Do Not Elevate the Common Terminal. The common terminal is at

ground potential. Do not connect the common terminal to elevated

voltages.

Do Not Operate With Suspected Failures. If you suspect there is damage

to this product, have it inspected by qualified service personnel.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

Safety Terms and Symbols

Terms in This Manual. These terms may appear in this manual:

WARNING. Warning statements identify conditions or practices that

could result in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that

could result in damage to this product or other property.

2P6101B Instructions

Features and Accessories

The P6101B probe is compatible with most general purpose

oscilloscopes that have a 1 MWinput impedance and bandwidth up

to 15 MHz.

NOTE. Remove and discard the protective cover on the tip of the

probe before attempting to connect a probe tip accessory.

BNC-to-probe tip adapter. To install the adapter,

push the wide end firmly into a BNC connector.

Then insert the probe tip firmly into the adapter.

Retractable hook tip. Use the retractable hook tip to

make hands-free measurements.

NOTE. For a solid connection, firmly push and

twist the hook tip onto the probe tip before using.

Marker rings. Attach the matching colored rings

onto the probe cable and tip as shown.

Features and Accessories

P6101B Instructions 3

Guard

Guard. The guard provides a finger barrier for

protection from electric shock.

WARNING. To avoid electric shock when using the probe, keep

fingers behind the guard on the probe body.

Ground Lead. Use the alligator clip to attach the

probe to a ground reference.

Long Ground Lead

Short Ground Lead

To see the best signal, use the shortest possible ground lead and

signal path.

4P6101B Instructions

Maintenance

This section describes how to maintain the probe.

Cleaning

To prevent damage to probe materials, avoid using chemicals that

contain benzine, benzene, toluene, xylene, acetone, or similar

solvents.

Do not immerse the probe or use abrasive cleaners.

Dirt may be removed with a soft cloth dampened with a mild

detergent and water solution, or isopropyl alcohol.

Replacing Probe Parts

Other than accessories, only the probe tip is replaceable.

Replacement probe tips are available as optional accessories. Refer

to the replaceable parts list at the end of this manual for more

information.

To remove a tip assembly, firmly grasp the pointed tip with pliers

and withdraw the assembly from the barrel.

No tools are required to install a replacement tip. Insert a new probe

tip into the probe barrel as far as possible using finger pressure. If

necessary, seat the plastic portion of the tip against the probe barrel

by pressing the tip gently but firmly against a hard surface, such as a

wood block or table top.

P6101B Instructions 5

Specifications

These characteristics apply to a P6101B probe. The instrument

connected to the probe must have a warm-up period of at least 20

minutes and be in an environment that does not exceed the limits

described in Table 2.

Table

: E

ara

istics

Attenuation (system) 1X1.05% at DC

Input Resistance (system) 1M1.0%

Input Capacitance 100 pF typical

System Bandwidth (–3 dB) DC to 15 MHz

Maximum Working (Nondestructive)

Input Voltage 300 V, CAT II

(See Figure 1 on page 7)

Specifications

6P6101B Instructions

Table

: Physic

d E

ron

ara

istics

Net Weight

(including accessories) t320 g (0.7 lb)

Cable Length 2 meters

Temperature Range1

Operating

Nonoperating

–15°C to +65°C

(+5°F to +149°F)

–62°C to +85°C

(–80°F to +185°F)

Humidity195% to 97% Relative Humidity

(30°C to 60°C)

1Tektronix Standard 062-2847-00, class 3. Refer to MIL-E-16400F, paragraph 4.5.9

through 4.5.9.5.1, class 4.

Table 3: Certifications and compliances

EC Declaration of

Conformity – Low

Voltage

Compliance was demonstrated to the following specification as

listed in the Official Journal of the European Communities:

Low Voltage Directive 73/23/EEC, as amended by 93/68/EEC:

EN 61010-1/A2:1995

Safety requirements for electrical equipment for

measurement, control, and laboratory use

EN 61010-2-031:1994

Particular requirements for hand-held probe assemblies for

electrical measurement and test equipment

Approvals UL3111-1 – Standard for electrical measuring and test equipment

IEC 1010-2-031 – Particular requirements for hand-held probe

assemblies for electrical measurement and test

CAN/CSA-C22.2 No. 1010.1-92 and CAN/CSA-C22.2 No.

1010.2.031-94 – Safety requirements for electrical equipment for

measurement, control, and laboratory use

Specifications

P6101B Instructions 7

Table 3: Certifications and compliances (Cont.)

Installation Category

Descriptions Terminals on this product may have different installation category

designations. The installation categories are:

CAT III Distribution-level mains (usually permanently

connected). Equipment at this level is typically

in a fixed industrial location

CAT II Local-level mains (wall sockets). Equipment at

this level includes appliances, portable tools,

and similar products. Equipment is usually

cord-connected

CAT I Secondary (signal level) or battery operated

circuits of electronic equipment

Pollution Degree 2 Do not operate in environments where conductive pollutants may

be present.

600V

500V

400V

300V

200V

100V

010MHz 15MHz1MHz

Figure 1: Maximum Working Voltage Derating Curve (VRMS)

8P6101B Instructions

Replaceable Parts

Optional Accessories

Standard Accessories

345

67 8

Figure 2: P6101B replaceable parts

Inhaltsverzeichnis

Andere Tektronix Prüfgeräte Handbücher

Tektronix

Tektronix 585 Bedienungsanleitung

Tektronix

Tektronix 2215A Bedienungsanleitung

Tektronix

Tektronix 551 Dual Beam Bedienungsanleitung

Tektronix

Tektronix 7B10 Bedienungsanleitung

Tektronix

Tektronix TEK 222 Bedienungsanleitung

Tektronix

Tektronix DPO70000SX Series Benutzerhandbuch

Tektronix

Tektronix TDS 460A Bedienungsanleitung

Tektronix

Tektronix ST2400A Bedienungsanleitung

Tektronix

Tektronix TDS 620A Bedienungsanleitung

Tektronix

Tektronix MTS415 Gebrauchs- und Pflegehandbuch

Tektronix

Tektronix TDS2000C series Bedienungsanleitung

Tektronix

Tektronix TDS2000C series Bedienungsanleitung

Tektronix

Tektronix 7704A Bedienungsanleitung

Tektronix

Tektronix MSO2024B Bedienungs- und Wartungshandbuch

Tektronix

Tektronix MTS400 Series Bedienungsanleitung

Tektronix

Tektronix P5205 Bedienungsanleitung

Tektronix

Tektronix MSO70000 Series Bedienungsanleitung

Tektronix

Tektronix 2 Series Gebrauchsanweisung

Tektronix

Tektronix TBS2000B Series Einrichtungshandbuch

Tektronix

Tektronix P6455 TTL/MOS Bedienungsanleitung

Tektronix

Tektronix 7D11 Bedienungsanleitung

Tektronix

Tektronix TDS 310 Bedienungsanleitung

Tektronix

Tektronix P7313 Bedienungsanleitung

Tektronix

Tektronix 2212 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung