Tektronix TDS 410A Bedienungsanleitung

Service Manual

TDS 410A, TDS 420A & TDS 460A

Digitizing Oscilloscopes

070-9217-01

Warning

The servicing instructions are for use by qualified

personnel only. To avoid personal injury, do not

perform any servicing unless you are qualified to

do so. Refer to the Safety Summary prior to

performing service.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

Printed in the U.S.A.

Tektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

KlipChip is a trademark of Tektronix, Inc.

WARRANTY

Tektronix warrants that this product will be free from defects in materials and workmanship for a period of three (3) years

from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either

will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the

defective product.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the

warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for

packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid.

Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the

Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any

other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate

maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting

from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair

damage resulting from improper use or connection to incompatible equipment; or c) to service a product that has been

modified or integrated with other products when the effect of such modification or integration increases the time or

difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THIS PRODUCT IN LIEU OF ANY

OTHER WARRANTIES, EXPRESSED OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND

EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX

AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS

ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

TDS 410A, TDS 420A & TDS 460A Service Manual i

Table of Contents

General Safety Summary ix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service Safety Summary xi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preface xiii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Introduction xvii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Before Servicing xvii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Strategy for Servicing xvii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tektronix Service xviii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications

Product Description 1–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Nominal Traits 1–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warranted Characteristics 1–17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Typical Characteristics 1–23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Information

Installation 2–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Supplying Operating Power 2–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Environment 2–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Applying and Interrupting Power 2–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Repackaging Instructions 2–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installed Options 2–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Information 2–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Screen Layout 2–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Basic Procedures 2–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Theory of Operation

Logic Conventions 3–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Module Overview 3–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Performance Verification

Performance Verification Procedures 4–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Conventions 4–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brief Procedures 4–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Self Tests 4–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Functional Tests 4–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Performance Tests 4–15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Prerequisites 4–15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Equipment Required 4–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Test Record 4–18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Signal Acquisition System Checks 4–20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Time Base System Checks 4–34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Trigger System Checks 4–38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output Signal Check 4–53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents

ii TDS 410A, TDS 420A & TDS 460A Service Manual

Sine Wave Generator Leveling Procedure 4–55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjustment Procedures

Requirements for Performance 5–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Usage 5–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Equipment Required 5–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjustment Instructions 5–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Probe Adjustment 5–10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Monitor Assembly Adjustment 5–21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

Related Maintenance Procedures 6–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preparation 6–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inspection and Cleaning 6–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal and Installation Procedures 6–9. . . . . . . . . . . . . . . . . . . . . . . . . .

Preparation — Please Read 6–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Access Procedure 6–13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Procedures for Module Removal and Installation 6–23. . . . . . . . . . . . . . . . . . . . . . . .

Disassembly for Cleaning 6–65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 6–69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Diagnostics 6–69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Firmware Updates 6–70. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting Equipment 6–71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Options

Options and Accessories 7–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Options 7–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Standard Accessories 7–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Optional Accessories 7–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrical Parts List

Electrical Parts List 8–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Diagrams

Diagrams 9–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Symbols 9–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Mechanical Parts List

Replaceable Parts 10–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Ordering Information 10–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Using the Replaceable Parts List 10–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents

TDS 410A, TDS 420A & TDS 460A Service Manual iii

List of Figures

Figure 1–1: TDS 400A Dimensional Drawing 1–15. . . . . . . . . . . . . . . . . . . .

Figure 2–1: Map of Display Functions 2–8. . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–1: Map of Display Functions 4–3. . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–2: Verifying Adjustments and Signal Path Compensation 4–6.

Figure 4–3: Universal Test Hookup for Functional Tests 4–8. . . . . . . . . .

Figure 4–4: Initial Test Hookup 4–20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–5: Initial Test Hookup 4–23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–6: Initial Test Hookup 4–26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–7: Measurement of Analog Bandwidth 4–29. . . . . . . . . . . . . . . . .

Figure 4–8: Initial Test Hookup 4–31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–9: Measurement of Channel Delay 4–33. . . . . . . . . . . . . . . . . . . .

Figure 4–10: Initial Test Hookup 4–34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–11: Measurement of Accuracy — Long-Term and

Delay-Time 4–37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–12: Initial Test Hookup 4–38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–13: Initial Test Hookup 4–41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–14: Measurement of Trigger Sensitivity 4–43. . . . . . . . . . . . . . . .

Figure 4–15: Initial Test Hookup 4–45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–16: Confirming Auxiliary Triggering at Maximum

Triggering Frequency 4–46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–17: Initial Test Hookup 4–47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–18:Adjusting Sync Pulse Amplitude 4–49. . . . . . . . . . . . . . . . . . .

Figure 4–19: Measurement of Video Sensitivity 4–50. . . . . . . . . . . . . . . . . .

Figure 4–20: Initial Test Hookup 4–52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–21: Initial Test Hookup 4–54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 4–22: Measurement of Probe Compensator Limits 4–55. . . . . . . . .

Figure 4–23: Sine Wave Generator Leveling Equipment Setup 4–56. . . . .

Figure 4–24: Equipment Setup for maximum Amplitude 4–57. . . . . . . . . .

Figure 5–1: Hookup for Probe Compensation 5–10. . . . . . . . . . . . . . . . . . .

Figure 5–2: Performing Probe Compensation 5–11. . . . . . . . . . . . . . . . . . .

Figure 5–3: Proper and Improper Probe Compensation 5–12. . . . . . . . . . .

Figure 5–4: Exposing the Inner Probe Tip 5–13. . . . . . . . . . . . . . . . . . . . . .

Figure 5–5: Initial Test Hookup 5–13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents

iv TDS 410A, TDS 420A & TDS 460A Service Manual

Figure 5–6: Exposing the Probe Body 5–16. . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 5–7: Initial Test Hookup 5–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 5–8: Probe Test Hookup 5–18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 5–9: Locations of Probe Adjustments 5–19. . . . . . . . . . . . . . . . . . . .

Figure 5–10:Adjustments vs. Front-Corner Response 5–20. . . . . . . . . . . .

Figure 5–11: Monitor Adjustment Locations 5–23. . . . . . . . . . . . . . . . . . . .

Figure 5–12: Five and Ten Percent Luminance Patches 5–24. . . . . . . . . . .

Figure 5–13: Composite Pattern for Focusing 5–25. . . . . . . . . . . . . . . . . . .

Figure 6–1: Oscilloscope Orientation 6–11. . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–2: Cabinet and Front-Panel Mounted Modules 6–16. . . . . . . . . .

Figure 6–3: Internal Modules 6–19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–4: Cables and Cable Routing 6–22. . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–5: Knob and Shaft Removal 6–24. . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–6: Line Fuse and Line Cord Removal 6–25. . . . . . . . . . . . . . . . . .

Figure 6–7: Front Cover, Rear Cover, Cabinet, EMI Gasket,

and Cabinet Handle and Feet Removal 6–27. . . . . . . . . . . . . . . . . . . . .

Figure 6–8: Trim Ring, Menu Elastomer,

and Menu Buttons Removal 6–30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–9: EMI Gasket Removal and Installation 6–32. . . . . . . . . . . . . . .

Figure 6–10: Disk Drive Removal 6–33. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–11: A06 Front-Panel Assembly, ESD Shield, and Menu Flex

and Probe Code Flex Circuits Removal 6–35. . . . . . . . . . . . . . . . . . . . .

Figure 6–12: Disassembly of the Front-Panel Assembly 6–36. . . . . . . . . . .

Figure 6–13:A05 Attenuator Removal 6–39. . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–14:A26 Monitor Assembly Removal 6–42. . . . . . . . . . . . . . . . . . .

Figure 6–15:A08 Jumper Board Assembly, D1 Bus,

and Board Supports Removal 6–43. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–16:A03 CPU Removal 6–45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–17:A02 Display Assembly Removal 6–47. . . . . . . . . . . . . . . . . . .

Figure 6–18:A09 DSP Assembly Removal 6–48. . . . . . . . . . . . . . . . . . . . . .

Figure 6–19:A01 Backplane Assembly and its Mount Removal 6–50. . . .

Figure 6–20: Battery Removal 6–53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–21:A25 Low Voltage Power Supply Removal 6–55. . . . . . . . . . .

Figure 6–22: Fan and Fan Mount Removal 6–58. . . . . . . . . . . . . . . . . . . . .

Figure 6–23: Line Filter Removal 6–59. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–24:Auxiliary Power Supply Removal 6–62. . . . . . . . . . . . . . . . . .

Figure 6–25:A04 Acquisition Board Removal 6–64. . . . . . . . . . . . . . . . . . .

Figure 6–26:Accessing the Protection Switch 6–70. . . . . . . . . . . . . . . . . . .

Table of Contents

TDS 410A, TDS 420A & TDS 460A Service Manual v

Figure 6–27: Console Port Connections 6–73. . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–28: Primary Troubleshooting Procedure 6–74. . . . . . . . . . . . . . .

Figure 6–29:A03 CPU Board Connector P1 6–75. . . . . . . . . . . . . . . . . . . .

Figure 6–30: Module Isolation Troubleshooting Procedure 6–76. . . . . . . .

Figure 6–31: Low Voltage Power Supply Troubleshooting Procedure 6–78

Figure 6–32: Power Supply Overload Troubleshooting Procedure 6–80. .

Figure 6–33:A25 Low Voltage Power Supply Module (Right Side) 6–81. .

Figure 6–34: Monitor Troubleshooting Procedure 6–82. . . . . . . . . . . . . . . .

Figure 6–35: Horizontal and Vertical Sync Signals 6–83. . . . . . . . . . . . . . .

Figure 6–36:A Video Signal with White, Black, and Blanking Levels 6–83

Figure 6–37:A26 Monitor Connector J440 6–84. . . . . . . . . . . . . . . . . . . . . .

Figure 6–38:A07 Auxiliary Power Connectors J4 and J7 6–84. . . . . . . . . .

Figure 6–39:A02 Display Connector J2 6–85. . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–40: Processor/Front Panel Troubleshooting Procedure 6–86. . . .

Figure 6–41:A06 Front Panel Board Power Connectors

J101 and J106 6–87. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–42:Attenuator/Acquisition Troubleshooting Procedure 6–88. . .

Figure 6–43:A08 Jumper and A05 Attenuator Boards

Signal Locations 6–89. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–44:Acquisition and Attenuator Power

Troubleshooting Procedure 6–90. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–45:A04 Acquisition Board Power Connector 6–91. . . . . . . . . . . .

Figure 6–46: Backplane Troubleshooting Procedure 6–92. . . . . . . . . . . . . .

Figure 6–47:A01 Backplane Module 6–94. . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6–48: I2C Isolation Troubleshooting Procedure 6–95. . . . . . . . . . . .

Figure 6–49: Console Troubleshooting Procedure 6–96. . . . . . . . . . . . . . . .

Figure 9–1: TDS 400A Interconnections 9–2. . . . . . . . . . . . . . . . . . . . . . . .

Figure 9–1: TDS 400A Interconnections (Cont.) 9–3. . . . . . . . . . . . . . . . .

Figure 9–2: TDS 400A Block Diagram 9–4. . . . . . . . . . . . . . . . . . . . . . . . .

Figure 9–2: TDS 400A Block Diagram (Cont.) 9–5. . . . . . . . . . . . . . . . . . .

Figure 10–1: External and Front Panel Modules 10–7. . . . . . . . . . . . . . . . .

Figure 10–2: Internal Modules 10–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 10–3: Cables and Routing 10–11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents

vi TDS 410A, TDS 420A & TDS 460A Service Manual

List of Tables

Table 1–1: Key Features of the TDS 400A Oscilloscopes 1–1. . . . . . . . . .

Table 1–2: Record Length vs. Divisions per Record 1–3. . . . . . . . . . . . . .

Table 1–3: Nominal Traits — Signal Acquisition System 1–9. . . . . . . . . .

Table 1–4: Nominal Traits — Time Base System 1–11. . . . . . . . . . . . . . . .

Table 1–5: Nominal Traits — Triggering System 1–11. . . . . . . . . . . . . . . .

Table 1–6: Nominal Traits — Display System 1–12. . . . . . . . . . . . . . . . . . .

Table 1–7: Nominal Traits — Data Storage 1–12. . . . . . . . . . . . . . . . . . . . .

Table 1–8: Nominal Traits — GPIB Interface, Video Output, and Power

Fuse 1–12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1–9: Nominal Traits — Mechanical 1–13. . . . . . . . . . . . . . . . . . . . . .

Table 1–10: Warranted Characteristics — Signal Acquisition System . . . . . .

1–17

Table 1–11: Warranted Characteristics — Time Base System 1–19. . . . . .

Table 1–12: Warranted Characteristics — Triggering System 1–20. . . . .

Table 1–13: Warranted Characteristics — Probe Compensator Output . . . .

1–20

Table 1–14: Warranted Characteristics — Power Requirements 1–20. . .

Table 1–15: Warranted Characteristics — Environmental, Safety, and

Reliability 1–21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1–16: Typical Characteristics — Signal Acquisition System 1–23. .

Table 1–17: Typical Characteristics — Time Base System 1–24. . . . . . . . .

Table 1–18: Typical Characteristics — Triggering System 1–25. . . . . . . .

Table 1–19: Typical Characteristics — Data Handling 1–26. . . . . . . . . . .

Table 2–1: Power-Cord Conductor Identification 2–2. . . . . . . . . . . . . . . .

Table 2–2: Power Cord Identification 2–2. . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–3: Effects of Corrupted Data 2–4. . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4–1: Test Equipment 4–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4–2: DC Offset Accuracy 4–22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4–3:Analog Bandwidth (TDS 410A and TDS 420A) 4–27. . . . . . . .

Table 4–4:Analog Bandwidth (TDS 460A) 4–28. . . . . . . . . . . . . . . . . . . . .

Table 5–1:Adjustments Required for Module Replaced 5–3. . . . . . . . . .

Table 5–2:Adjustments and Dependencies 5–4. . . . . . . . . . . . . . . . . . . . .

Table 5–3: Test Equipment, Fixtures, and Supplies 5–5. . . . . . . . . . . . . .

Table 5–4: GPIB Board Configuration1 5–7. . . . . . . . . . . . . . . . . . . . . . . .

Andere Handbücher für TDS 410A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tektronix Prüfgeräte Handbücher

Tektronix

Tektronix 371B Bedienungsanleitung

Tektronix

Tektronix TBS2000B Series Handbuch

Tektronix

Tektronix 585 Bedienungsanleitung

Tektronix

Tektronix PRISM Bedienungsanleitung

Tektronix

Tektronix TDS5000 Series Bedienungsanleitung

Tektronix

Tektronix 5000 Series Bedienungsanleitung

Tektronix

Tektronix SD-14 Bedienungsanleitung

Tektronix

Tektronix 2465A Bedienungsanleitung

Tektronix

Tektronix 7B87 Bedienungsanleitung

Tektronix

Tektronix DPO2002B Bedienungsanleitung

Tektronix

Tektronix TDS3000B Series Bedienungsanleitung

Tektronix

Tektronix MDO3000 Series Bedienungsanleitung

Tektronix

Tektronix 4000 Series Bedienungsanleitung

Tektronix

Tektronix 2445 Bedienungsanleitung

Tektronix

Tektronix TDS1000 Series Bedienungsanleitung

Tektronix

Tektronix MSO46B Montage- und Wartungsanleitung

Tektronix

Tektronix 7854 Bedienungsanleitung

Tektronix

Tektronix DS1001G Bedienungsanleitung

Tektronix

Tektronix TMT4 Gebrauchs- und Pflegehandbuch

Tektronix

Tektronix TDS1000 Series Bedienungsanleitung

Tektronix

Tektronix MSO54B Bedienungsanleitung

Tektronix

Tektronix 321 Series Handbuch

Tektronix

Tektronix MTS415 Gebrauchs- und Pflegehandbuch

Tektronix

Tektronix KEITHLEY EC-UPGRADE Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung