Teledyne MVX-7100 mL Bedienungsanleitung

MVX-7100 µL Workstation Plug-In

For Agilent MassHunter™ Workstation Software

Manual Part Number 32-0059-048 Rev 0, April 3, 2017

Installation Guide

32-0059-048 Rev 0, April 3, 2017,

Teledyne CETAC Technologies authorizes its

customers to reproduce, transmit, or store

this document in its entirety, including this

page, for the express purpose of installing,

operating, or maintaining the product

described herein.

Teledyne CETAC Technologies

Customer Service & Support

14306 Industrial Road

Omaha, Nebraska 68144, USA

Phone (800) 369-2822 (USA only)

Phone (402) 733-2829

Fax (402) 733-1932

E-mail cetacservice@teledyne.com

REVISIONS

Teledyne CETAC Technologies strives to

provide the scientific community with an

unparalleled combination of effective

technology and continuing value. Modular

upgrades for existing instruments will

continue to be a prime consideration as

designs progress.

Teledyne CETAC Technologies reserves the

right to revise this document and improve

products described herein at any time without

notice or obligation.

TRADEMARK ACKNOWLEDGEMENTS

Windows is a registered trademark of

Microsoft Corporation in the United States and

other countries.

MassHunter is a trademark of Agilent

Technologies Inc.

All other marks are the property of their

respective owners.

Contents

1Introduction ..............................................................................................................4

Overview.................................................................................................................................... 4

Requirements .......................................................................................................................... 4

Where to Go for More Information................................................................................ 5

2Setting Up the Hardware ......................................................................................6

3Installing and Configuring the Plug-In ............................................................7

Installing the Plug-In............................................................................................................ 7

Opening the Hardware Configuration Window ....................................................... 8

Configuring the COM Port .................................................................................................. 9

Determining Which COM Port To Use.................................................................... 9

Configuring the COM Port Number.......................................................................10

Configuring the Plugin for Your Hardware ..............................................................10

Using the Plug-In..................................................................................................................10

1Introduction

Overview

Use the Teledyne CETAC Technologies autosampler plug-in to operate a CETAC

MVX-7100 µL workstation with the Agilent MassHunter™ Workstation

software.

Without the plug-in, the MVX-7100 workstation must be controlled by the

CETAC Workstation software. With the plug-in, however, you do not need to

use the CETAC Workstation software.

The Teledyne CETAC Technologies MVX-7100 µL workstation provides sample

handling (sample preparation and sample introduction capability) for sample

volumes down to 5 µL for ICP-MS instrumentation. The syringe-driven sample

introduction and subsequent rinse cycles allow for stable low-flow

applications with low detection limits. Syringe aliquot control combined with

flow injection allows for accurate sample volumes to be handled with superior

washout. The MVX-7100 µL workstation utilizes a non-metallic liquid-facing

flow path to minimize system background and provide low detection limits.

Requirements

Before you use this software, you need:



An Agilent ICP-MS (installed and operating).



Agilent MassHunter™ Workstation software version 4.3 or later.



A CETAC MVX-7100 µL workstation (with all of the accessory modules

you plan to use installed).



The CETAC MVX-7100 software CD.

MVX-7100 Plug-In for MassHunter

Chapter 1: Introduction

Where to Go for More Information

In addition to this manual, you can refer to the following resources:

The CETAC MVX-7100 µL Workstation Operator’s Manual provides

information about installing and maintaining the MVX-7100 µL

workstation.

Tel edyne CETAC Technologies Customer Service and Support:

Phone: 1 (800) 369-2822 (USA only)

1 (402) 733-2829

Fax: 1 (402) 733-1932

E-mail: cetacservice@teledyne.com

2 Setting Up the

Hardware

You will need to install the plug-in before you can complete setting up the

MVX-7100 µL workstation. This is because the syringes pumps need to be at

the 1/2 position in order to install the syringe barrels. If necessary, you can use

the Direct Controls in the plug-in to move the syringe pumps to the proper

position.

The CETAC MVX-7100 µL Workstation Operator’s Manual provides information

about installing the MVX-7100 µL workstation.

3 Installing and

Configuring the Plug-In

Before you can create or run any methods with the MVX-7100 workstation,

you must install the plug-in and configure it for your hardware. The plug-in

reads the configuration information from when it is started.

Under Mainframe Properties>External Device, there is a listing for the MVX-

7100. Nothing there needs to be changed. All settings are in the plug-in’s

hardware configuration window.

Installing the Plug-In

1Run the installer from the MVX-7100 software CD.

2Start the MassHunter software.

3Under Sample Introduction, enable Use ALS.

MVX-7100 Plug-In for MassHunter

Chapter 3: Installing and Configuring the Plug-In

4Under Autosampler(ALS), click Properties and set the autosampler type to

MVX-7100.

The autosampler will appear in the list of hardware:

If the plug-in does not appear in MassHunter, check that the MassHunter

software was installed in the default location.

Opening the Hardware Configuration Window

There are two ways to open the configuration window:

1Click the Autosampler(ALS) and choose MVX Settings….

2In the plug-in window, select Settings & Info > Configuration > MVX

Settings….

MVX-7100 Plug-In for MassHunter

Chapter 3: Installing and Configuring the Plug-In

Configuring the COM Port

The plug-in will need to know which COM port is connected to the

autosampler.

Determining Which COM Port To Use

If you are using a USB connection, the COM port numbers were assigned by the

Windows when you connected the USB cables for the first time. Ideally, the

port numbers were written down at that time.

If you do not know which port numbers were assigned, you can use the

Windows Device Manager to distinguish the port numbers:

1Connect the USB cables between the computer and the autosampler, and turn

them on.

2Open the Windows Device Manager. The quickest way to do this is to click the

Windows Start button and enter “device manager” in the search field.

3In Device Manager, click Ports (COM & LPT). You will see a list of all of the

COM port numbers which have been assigned.

FIGURE 3-1

COM Port Assigned to a USB Port in Device Manager

4Unplug the USB cable from the autosampler.

5Note which COM port disappears from the list. This is the port number of the

autosampler.

6Plug the USB cable back in.

MVX-7100 Plug-In for MassHunter

Chapter 3: Installing and Configuring the Plug-In

Configuring the COM Port Number

1In the hardware configuration window, click the COM Port tab.

2Select the COM port number from the list.

3Enable Auto Connect.

When Auto Connect is enabled, the plug-in will automatically connect to the

chosen COM port every time it is started.

If Auto Connect is not enabled, you will need to set the COM port every time

you run the plug-in.

Configuring the Plugin for Your Hardware

After you change any of the hardware configuration settings, exit and restart

the MassHunter software.

Before you can create or run any methods, you must configure the plug-in so

that it knows what hardware is present. The plug-in reads the configuration

information when it is started. See the plug-in help for more information.

Using the Plug-In

Click the help button in the plug-in for instructions on configuring the plug-in,

creating methods, and running batches of samples.

For information on using the plug-in, start MassHunter and select Settings &

Info>General>Help.

Inhaltsverzeichnis

Andere Teledyne Desktop Handbücher

Teledyne

Teledyne SDC10 Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

HP Z1 Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung