Teledyne T3AFG30 Bedienungsanleitung

T3AFG30 / T3AFG60

Function / Arbitrary Waveform Generators

Quick Start Guide

Contents

General Safety Summary .......................................................................................... 1

Handle Adjustment .................................................................................................... 3

The Front Panel .................................................................................................... 4

Back Panel ............................................................................................................ 9

TFT Color Display ............................................................................................... 11

Built-In Help System … ......................................................................................... 13

Introduction To EasyWaveX … ............................................................................. 13

Certications … .................................................................................................... 14

Users are permitted to duplicate and distribute Teledyne LeCroy, Inc.

documentation for internal educational purposes only. Resale or unauthorized

duplication of Teledyne LeCroy publications is strictly prohibited.

Teledyne Test Tools is a trademark of Teledyne LeCroy, Inc., Inc. Other product or

brand names are trademarks or requested trademarks of their respective holders.

Information in this publication supersedes all earlier versions.

Specications are subject to change without notice.

General Safety Summary

Read the following precautions carefully to avoid any personal

injuries, or damage to the instrument or products connected to it.

Use the instrument only as specied.

Use only the power cord supplied for the instrument.

Ground the instrument. The instrument is grounded through the

ground conductor of the power cord. To avoid electric shock,

always connect to grounded outlets. Make sure the instrument is

grounded correctly before connecting its input or output terminals.

Do not connect external signals. The BNC connector is used to

output the generated waveforms only. No external signals should

be connected to the BNC, or the instrument may be damaged.

Observe all terminal ratings and signson the instrument to

avoid re or electric shock. Before connecting to the instrument,

read the manual to understand the input/output ratings.

Do not operate with suspected failures. If you suspect that the

instrument is damaged, contact the Teledyne LeCroy service

department immediately.

Do not operate in wet/damp conditions.

Do not operate in an explosive atmosphere.

Keep the surface of the instrument clean and dry.

Avoid touching exposed circuits or wires. Do not touch

exposed contacts or components when the power is on.

Do not operate without covers. Do not operate the instrument

with covers or panels removed.

Use proper overvoltage protection.

Observe ventilation requirements. Ensure good ventilation.

Check the vent and fan regularly to prevent overheating.

Safety Terms and Symbols

The following terms may appear on the instrument:

DANGER:

Direct injury or hazard may occur.

WARNING:

Potential injury or hazard may occur.

CAUTION:

Potential damage to instrument/property may occur.

The following symbols may appear on the instrument:

CAUTION

Risk of

injury or

damage.

Refer to

manual.

WARNING

Risk of

electric

shock or

burn

Earth

Ground

Terminal

Protective

Conductor

Terminal

Frame or

Chassis

Terminal

ON/

Standby

Power

Alternating

Current

Operating Environment

Temperature: 0 °C to 40 °C

Relative Humidity: 5 to 90% RH at ≤ 30 °C

Altitude: ≤ 3048 m at ≤ 30 °C

Use indoors only.

Pollution degree 2. Use in an operating environment where

normally only dry, non-conductive pollution occurs. Temporary

conductivity caused by condensation should be expected.

AC Power

Input Voltage & Frequency: 100-120 V at 400 Hz or

100-240 V at 50/60 Hz

Automatic AC selection.

Power Consumption: 50 W maximum

Mains Supply Connector: CAT II per IEC/EN 61010-1:2010,

instrument intended to be supplied from the building wiring at

utilization points (socket outlets and similar).

Handle Adjustment

Users can adjust the handle to the required position by pulling

the mounting points outward and adjusting the handle position.

Handle Adjustment

Horizontal Position

Carrying Position

1011

1 Power Button

2 USB Host Port

3 TFT Display

4 Numeric Keypad

5 Adjust Knob

6 Arrow Keys

7 CH1/CH2 Control/Output Port

8 Channel Select Key

9 Function Keys

10 Waveform Selection Key

11 Menu Keys

1. Power Button

Used to turn on/o the waveform generator. When the power button is o, the

generator is under power o state.

2. USB Host Port

Used to read waveforms or status les from a USB drive or save current

instrument status to a USB drive. Firmware can be updated through the USB

port. The waveform generator supports a FAT formatted USB drive.

3. TFT Display

The waveform generator has a 4.3 inch TFT color LCD display, which can

display the current function menu, parameter settings, system state, and help.

4. Numeric Keypad

Consists of numbers from 0 to 9, radix points “.” and symbol keys “+/-”, which

are used to input parameters.

Note：To enter a negative number enter a “-” symbol before the numbers.

Front Panel

5. Adjust Knob

●Used to increase (clockwise) or decrease (anticlockwise) the current

numerical value when setting parameters.

●Also used to change characters when inputting a le name.

●When saving or reading les, rotate the knob to choose a position to save a

le or choose a le to be read; press the knob to open a selected folder or

le.

6. Arrow Keys

●Used to adjust digits in numeric values when using the knob to set

parameters.

●Also used to position the cursor when inputting a le name.

●When saving or reading les, the arrow keys are used to choose a position

to save a le or choose a le to be read.

7. CH1 Control Port/Output Button

●The Output button on the left is used to turn on/o CH1 output.

●The nominal output impedance of the BNC connector is 50 Ω.

●When pressing Output the key backlight turns on, and the connector

outputs waveforms according to the current conguration of CH1.

CH2 Control Port/Output Button

●The Output button on the right is used to turn on/o CH2 output.

●The nominal output impedance of the BNC connector is 50 Ω.

●When pressing Output, the backlight turns on, and the connector outputs

waveforms according to the current conguration of CH2.

CAUTION:

Over voltage protection of CH1 and CH2 will take eect once any of the following

conditions is met. When over voltage protection occurs, a message will be

displayed and the output is disabled.

•The absolute value of input voltage is higher than 11 V ± 0.5 V when the amplitude of

the generator is higher than or equal to 2Vpp or the DC oset is higher than or equal

to |3VDC| under HighZ load.

•The absolute value of input voltage is higher than 4 V ± 0.5 V when the amplitude of

the generator is lower than 2 Vpp and the DC oset is lower than |3 VDC| under HighZ

load.

Choose Utility → → to turn on/o the function.

8. Channel Select Key

Used to switch the current selected channel between CH1 and CH2.

9. Function Keys

Mod ----Modulation

Used to enable the modulation screen and allow for modulation selection. The

selection is AM, DSB-AM, FM, PM, ASK, FSK, PSK and PWM modulated signals.

• It supports “Internal” and “External” modulation sources.

•The corresponding backlight will turn on when this function is selected.

Sweep ----Sweep

Used to generate sweeping frequency signals of Sine, Square, Ramp and Arbitrary.

• It supports “Linear” and “Log” sweep proles.

• It supports “Internal”, “External” and “Manual” trigger sources.

• The corresponding backlight will turn on when this function is selected.

Burst ----Burst

Used to generate burst signals of Sine, Square, Ramp, Noise and Arbitrary.

• It supports “NCycle”, “Gated” and “Innite” burst modes.

• Noise can only be used to generate gated burst.

• It supports “Internal”, “External” and “Manual” trigger sources.

• The corresponding backlight will turn on when this function is selected.

Parameter ----Parameter Setting

Used to switch directly to the parameter setting interface.

• The corresponding backlight will turn on when this function is selected.

Utility ----Utility Functions and System Settings

Used to set system parameters and check version information.

• Press this key and then press the help key to obtain built-in help information

about the product.

• The corresponding backlight will turn on when this function is selected.

Store/Recall ----Store and Recall

Used to store/recall the instrument’s setup or arbitrary waveform data edited by

users.

• Can be used to perform general le operations.

• In addition to the built-in nonvolatile memory (C disk), an external USB drive (D

disk) can be used to store data.

• The corresponding backlight will turn on when this function is selected.

10.Waveform Selection Key

Waveforms ---- Sine

Provides sine wave output which ranges from 1 μHz to 30 MHz or 60 MHz, depending

on the model.

•The Waveforms backlight will turn on when this function is selected.

• The sine wave “Frequency/Period”, “Amplitude/High level”, “Oset/Low level” and

“Phase” can be adjusted.

Waveforms ---- Square

Provides square wave output which ranges from 1 μHz to 30 MHz or 60 MHz,

depending on the model.

• The Waveforms backlight will turn on when this function is selected.

• The square wave “Frequency/Period”, “Amplitude/High level”, “Oset/Low level”,

“Phase” and “Duty” can be adjusted.

Waveforms ---- Ramp

Provides ramp waveform output which ranges from 1 μHz to 500 kHz.

• The Waveforms backlight will turn on when this function is selected.

• The ramp waveform “Frequency/Period”, “Amplitude/High level”, “Oset/Low

level”, “Phase” and “Symmetry” can be adjusted.

Waveforms ---- Pulse

Provides pulse waveform output which ranges from 1 μHz to 12.5 MHz.

• The Waveforms backlight will turn on when this function is selected.

• The pulse waveform “Frequency/Period”, “Amplitude/High level”, “Oset/Low level”,

“Pulse width/Duty”, “Rise/Fall” and “Delay” can be adjusted.

Waveforms ---- Noise

Provides White Gauss Noise output with a bandwidth of the waveform generator

model.

• The Waveforms backlight will turn on when this function is selected.

• “Stdev” and “”Mean” of the noise signal can be adjusted.

Waveforms ---- Arb

Provides arbitrary waveform output which ranges from 1μHz to 6 MHz.

• The Waveforms backlight will turn on when this function is selected.

• Supports two output modes: “DDS” and “TrueArb”.

• Built-in waveforms include Cardiac, Gauspuls, ExpRise and ExpFall, etc. In

addition, it can output waveforms stored on a USB drive.

• Users can edit arbitrary waveforms through PC software and download them to

the instrument.

• Arbitrary waveforms can be adjusted for “Frequency/Period”, “Amplitude/High

level”, “Oset/Low level” and “Phase”.

11. Menu Keys

These keys correspond to the menu displayed above them on the display. Press any

button to activate the corresponding menu.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teledyne Prüfgeräte Handbücher

Teledyne

Teledyne HDO9000 Bedienungsanleitung

Teledyne

Teledyne waverunner xi-a series Stücklistenhandbuch

Teledyne

Teledyne Everywhereyoulook T3DSOH1000 Bedienungsanleitung

Teledyne

Teledyne T703 Bedienungsanleitung

Teledyne

Teledyne T3DAQ1-16 Bedienungsanleitung

Teledyne

Teledyne LeCroy T3DSO2000A Series Bedienungsanleitung

Teledyne

Teledyne HPM 4 Bedienungsanleitung

Teledyne

Teledyne T3DSO1000A Series Bedienungsanleitung

Teledyne

Teledyne PXP-100B Bedienungsanleitung

Teledyne

Teledyne T3DSO2000 Bedienungsanleitung

Teledyne

Teledyne HDO8000A Bedienungsanleitung

Teledyne

Teledyne T3DSO3000 Bedienungsanleitung

Teledyne

Teledyne ZD200 Stücklistenhandbuch

Teledyne

Teledyne T3DSO1000 Betriebsanleitung

Teledyne

Teledyne CD14 Bedienungsanleitung

Teledyne

Teledyne LabMaster 10 Zi Series Stücklistenhandbuch

Teledyne

Teledyne VISION G2 CLASSIC 6 Bedienungsanleitung

Teledyne

Teledyne LeCroy Waverunner LT Series Merkblatt

Teledyne

Teledyne HDO4000 Bedienungsanleitung

Teledyne

Teledyne T3HVD Bedienungsanleitung

Teledyne

Teledyne Reson PDS Technisches Datenblatt

Teledyne

Teledyne T750 Bedienungsanleitung

Teledyne

Teledyne FST-040 Bedienungsanleitung

Teledyne

Teledyne GT Series Kurzanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung