Telegesis ZigBee ETRX3USB Bedienungsanleitung

Telegesis

TG-ETRX357USB-PM-014-102

ETRX3USB

Product Manual 1.02

ZigBee®USB STICKS:

ETRX3USB

ETRX3USB-LRS

ETRX3USB+8M

ETRX3USB-LRS+8M

PRODUCT MANUAL

ETRX3USB

Table of Contents

1INTRODUCTION.................................................................................................................3

1.1 Supported Operating Systems .........................................................................................3

2ABSOLUTE MAXIMUM RATINGS .....................................................................................4

38MB FLASH MEMORY.......................................................................................................4

3.1 Connections.....................................................................................................................4

3.2 Firmware..........................................................................................................................4

4OPERATING CONDITIONS................................................................................................5

5REGULATORY INFORMATION.........................................................................................6

5.1 FCC compliance Class B Digital Device...........................................................................6

5.2 Canada –Industry Canada (IC)........................................................................................6

5.3 European Certification......................................................................................................6

5.4 General............................................................................................................................7

6ETRX357 I/O CONNECTIVITY............................................................................................7

7FIRMWARE UPGRADES ...................................................................................................7

8DRIVER INSTALLATION AND OPERATION.....................................................................8

8.1 Windows XP/Vista/7 Driver Installation.............................................................................8

8.2 Macintosh and Linux drivers...........................................................................................10

9CUSTOM FIRMWARE DEVELOPMENT ..........................................................................10

10 ORDERING INFORMATION.............................................................................................12

11 TRADEMARKS.................................................................................................................13

12 DISCLAIMER....................................................................................................................13

13 CONTACT INFORMATION...............................................................................................13

14 REFERENCES..................................................................................................................13

ETRX3USB

1 Introduction

The ETRX3USB ZigBee USB Stick is effectively an RS232 to USB bridge connected to an ETRX3

Series ZigBee module. This allows connectivity to a computer’s USB port.

The ETRX3USB+8M and ETRX3USB-LRS+8M include an 8Mbit flash memory chip which can be

accessed by the firmware in the EM357 ZigBee chip inside the USB stick.

The ETRX3USB-LRS and ETRX3USB-LRS+8M have an ETRX357-LRS module in place of the

ETRX357 for longer range. The LRS variant has higher output power and better receiver

sensitivity; consult the ETRX357 and ETRX357-LRS Product Manuals for the full details.

The supplied Windows drivers create a virtual COM Port, so that the command line of the ETRX3

series module can be accessed via any terminal software application.

When using Windows®the Telegesis Terminal application can be used as described in the

ETRX357 Development Kit manual.

1.1 Supported Operating Systems

Windows 98SE

Windows XP/Vista/7

Windows 2000

Windows CE *

MAC OS-9

MAC OS-X *

Linux *

* drivers for these systems are available from Silicon Labs. The bridge chip is a CP2102 with

Vendor ID 0x10C4 and Product ID 0x8293.

ETRX3USB

2 Absolute Maximum Ratings

Parameter

Min.

Max.

Units

Condition

Supply Voltage Vdd

-0.3

5.5

Voltage on any pin

-0.3

Vdd+0.3, max 5.8

Storage Temperature range

-40

150

°C

Table 1: Absolute Maximum Ratings

The absolute maximum ratings given above should under no circumstances be violated.

Exceeding one or more of the limiting values may cause permanent damage to the device.

3 8Mb flash memory

3.1 Connections

The +8M devices in the USB stick family contain a Winbond W25Q80B 8Mb serial flash memory

chip with SPI interface to the EM357. The pin connections to the EM357 are shown in Figure 1.

Figure 1. Flash memory connections to EM357

At the time of writing the datasheets for the family of Winbond W25Q80Bx flash memory chips is

available at:

www.winbond.com/hq/enu/ProductAndSales/ProductLines/FlashMemory/SerialFlash

3.2 Firmware

The Telegesis R3xx firmware does not have any capability of driving the SPI connection to the

memory chip. Users will have to write or commission custom firmware to make use of this external

memory.

/CS

/WP

GND

VCC

/HOLD

CLK

PA0

PA3

PA2

PA1

VCC

W25Q80B

VCC

GND

ETRX3USB

4 Operating Conditions

Typical values at 5V 25°C.

Parameter

Min.

Typ.

Max.

Units

Condition

Supply Voltage, Vdd

4.5

5.5

Supply Current

ETRX3USB

561

TX 8dBm

542

TX 3dBm

541

TX –43dBm

52.51

29.51,3

SED, Power Mode 01

271,2

SED, Power Mode 02

261,2

SED, Power Mode 03

Operating ambient

temperature range

-20

°C

Table 2: Operating Conditions

The Winbond memory chip in the 8M variants draws extra current as shown in Table 3. Full details

of its power consumption can be found in the Winbond W25Q80Bx family datasheets.

Operation

Current

Units

Typ

Max

Standby

µA

Read 1MHz

Write Status Register

Page Program

Sector/Block Erase

Chip Erase

Table 3: Flash memory current consumption

During USB suspend the current will drop by 25.6mA in all modes.

Please note that the power consumption in various power modes is firmware and usage dependent.

ETRX3USB

5 Regulatory Information

The ETRX3USB and ETRX3USB+8M as well as the ETRX3USB-LRS and ETRX3USB-LRS+8M

have been designed to meet all national regulations for world-wide use. In particular the following

certifications have been obtained:

5.1 FCC compliance Class B Digital Device

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause

undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Modifications not expressly approved by the manufacturer could void the user's authority to

operate the equipment under FCC rules. An FCC declaration of conformity is available separately

from the Telegesis website

The ETRX3USB and ETRX3USB+8M contain a modular radio transmitter with FCC ID

S4GEM35XA. The ETRX3USB-LRS and ETRX3USB-LRS+8M contain a modular radio transmitter

with FCC ID S4GEM35XB.

5.2 Canada –Industry Canada (IC)

This Class B digital device complies with Canadian ICES-003. Cet appareil numérique de la

classe B est conforme à la norme NMB-003 du Canada.

5.3 European Certification

The ETRX3USB and ETRX3USB+8M as well as the ETRX3USB+LRS and ETRX3USB-LRS+8M

limited to a maximum power level of 21.15mW e.i.r.p. (13.2dBm) have been tested and comply

with the following standards:

ETRX3USB

Radio: EN 300 328 v1.7.1 (10/2006)

EMC: EN 301 489-17 v2.1.1 (09/2008)

Safety: EN 60950-1:2006

An EC declaration of conformity is available separately from the Telegesis website.

Important Note: In Europe the regulations for the 2.4GHz frequency band only permit.a maximum

power spectral density of 10mW/MHz, which with a ZigBee spectrum equates to an e.i.r.p of

13dBm. The ETRX3USB cannot reach this level but the ETRX3USB-LRS can exceed it, so in the

latter device the power out of the EM357 chip into the RF power amplifier should be limited to -

11dBm. Refer to the ETRX357-LRS Product Manual for more details.

5.4 General

For further technical information, including radio certification, see the corresponding ETRX3 series

Module Product Manuals.

When ordering ETRX3USB sticks without printed branding on the case, you may be responsible

for applying a marking appropriate to their geographical area of use, such as the CE marking.

For more information on ZigBee compliance and the AT command interface firmware please refer

to the latest AT command dictionary and the ETRX357 user guide.

6 ETRX357 I/O Connectivity

The I/Os of the built-in ETRX357 are connected as follows:

PA6 is connected to the LED (drive PA6 low to sink LED current).

PB3 is the CTS input for the ETRX357. Make sure PB3 is never defined as an output.

PB4 is the RTS input for the ETRX357.

Important Note: The lines for hardware handshaking are connected, so even when not using

hardware handshaking PB3 should never be defined as an output as this would drive against the

incoming CTS signal via a 1kΩresistor and increase the current consumption.

7 Firmware upgrades

The firmware which is loaded onto the embedded ETRX357 Module can be upgraded over the air

or via the virtual COM port as described in the ETRX357 Development Kit Product Manual.

Alternatively, access to the SIF programming interface is possible by opening the cover on the side

of the ETRX3USB ZigBee USB stick.

ETRX3USB

8 Driver Installation and Operation

The drivers provided will generate a virtual COM port allowing easy access to the serial port of the

embedded ETRX357.

To read more about the ETRX357 wireless mesh networking module and its command line

interface please read the corresponding documentation which can be found at

www.telegesis.com/support/document_centre.htm.

8.1 Windows XP/Vista/7 Driver Installation

The driver package downloadable from the Support



Software download page at

www.telegesis.com/telegesis_zigbee_technology_-_technical_support_/software_download.htm

should be unzipped into a local folder. When executing the file ‘TgVCPInstaller.exe’ prior to

plugging in the ETRX3USB stick an installer will guide you through the steps required for the driver

installation.

Figure 2: Found New Hardware Wizard

After insertion of the stick, Windows®may prompt that new hardware has been found. If you have

run the ‘TgVCPInstaller.exe’ Windows will be able to install the driver by automatically, but if you

have not run ‘TgVCPInstaller.exe’ you will have to manually point to the directory into which you

have unzipped the driver.

Please note that each ETRX3USB has a unique serial number which requires the installation

procedure to be repeated with every new ETRX3USB being attached to the computer, though the

process is not obtrusive. This allows multiple ETRX3USB sticks to be used on the same computer

at any one time.

In order to find out the identity/number of the virtual COM port the stick has been assigned to,

please open the Device Manager under the Windows Computer Management screen (see below)

and click on the Ports (COM and LPT) section where you should find the new virtual COM port. By

ETRX3USB

double clicking on the entry of the virtual COM port you can also change the number assigned to

the virtual COM port when entering the advanced setup of the device.

Figure 3. Device Manager

Once the correct COM port has been selected, the Terminal software can be used to control the

ETRX3USB stick as per the Development Kit Manual. Telegesis Terminal is a free download from

www.telegesis.com/telegesis_zigbee_technology_-_technical_support_/software_download.htm

ETRX3USB

Figure 4. Telegesis Terminal

8.2 Macintosh and Linux drivers

A Virtual Com Port driver kit for Mac and Linux can be obtained by following the link on our website

on the Support



Software download page. Recent versions of the Linux kernel have native

support for Telegesis USB devices.

The Silicon Laboratories CP2102 serial-to-USB bridge chip is configured with Vendor ID 0x10C4

and Product ID 0x8293, and the drivers must be written to recognise these identifiers.

9 Custom Firmware Development

If you intend to develop custom firmware to go onto the ETRX3USB you need to contact Silicon

Labs to obtain access to their suite of development tools and their stack. The USB stick contains

an ETRX357 module based on the Silicon Labs EM357 and a USB-to-serial bridge chip. The

ETRX357 communicates via its serial port, so the user’s firmware must use the UART of Serial

Controller 1. The nRTS and nCTS lines are connected to the USB bridge chip. The LED on the

USB stick is driven from EM357 pad PA6.

In order to download custom firmware onto the ETRX357, the Silicon Labs bootloader can be used

or alternatively the ETRX3USB can be directly connected to the Silicon Labs InSight Adapter for

programming and real time debugging.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Telegesis Adapter Handbücher

Telegesis

Telegesis ETRX2USB Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung