Televes DATBOSSMIX LR Bedienungsanleitung

MIX LR

Antenna assembly / Montaje de la antena

R x2 S W x3

Proceed to insert UHF directors B1 , B2 and B3

into the corresponding booms main assembly

Aby inserting the director end insert into the

corresponding location in main assembly A(“b1”

into“a1”,“b2” into “a2”, and “b3”into“a3”) then secure

them using bolts Rand Sand nuts W.

The B1 , B2 , B3 UHF directors are dierent sizes

and lengths so make sure to insert them in the right

positions, the longest director B1 goes in the upper

position of the antenna and the shortest director

B3 goes in the lower position of the antenna.

Note: Tighten the nuts Wuntil the square carriage

heads of the bolts Rand Ssink into the aluminum

and the heads sit ush with the boom. The bolt base

will bite into the aluminum, securing the joint.

Place plastic UHF director spacers Dand Eon

the director booms to match the screw holes of

director(s) B1 , B2 & B3 elements. Secure them

with three Vphillips head screws.

Note: Be sure to place the spacers with the largest

opening (slot) for the directors on the shortest

bottom director B3 .

Move the top and bottom director booms

assembled in step 1 in the direction indicated by

the arrows on main assembly Auntil the horizontal

director elements of all three director booms line up.





Note: Start the assembly procedure after thoroughly checking all parts and becoming familiar with them.

NEEDED

TOOLS



(a1)

(a2)

(a3)

(b1)

Included 10mm wrench Screw driver Cutter or Cable stripper

(b2)

(b3)

D E V x3

PH #2

Scan to

watch

assembly

video

Place the plastic spacers Fon the support braces

H, closer to the curved part of the support brace

as indicated. Slide the mounting clamp assemblies

Gon the support braces starting from the support

brace end that is not curved and tighten the bolts

loosely once in place over the plastic spacers F, as

they will be fully tightened later.

Note: The mounting clamp assemblies must

be installed so that the nuts face the left side of

the antenna, when looking from the back of the

antenna, to allow for vertical tilt once the antenna

has been installed on the mast. Before proceeding to

the next step make sure the plastic spacers Fand

mounting clamp assemblies Gare installed in the

right orientation.

Place the support brace assemblies completed on

step 4 on directors B1 (top) and B3 (bottom)

as indicated, and attach them with two pieces of

carriage bolt Tand nut Wper each support brace.

Make sure the U-bolt side of the mounting clamps

both are located on the left side of the support

braces looking at it from a rear view. Line up the

clamps so that they are ready for mounting once

assembly is complete.

Note: Tighten the nuts Wuntil the square carriage

head of the bolts Tsink into the aluminum and the

heads sit ush with the boom. The bolt base will bite

into the aluminum, securing the joint.

Mount the two black plastic locks Lon the rst rear

reector self-locking clamp Kbottom piece.

Locate the mounting hole on aluminum Main

assembly Anext to and behind the orange plastic

main body of the antenna, place self-locking clamp

Jtop piece on Alined up with the hole in Aand

bottom piece K, secure with bolt U(bolt Ugoes

through Jand threads into K).

Place the MUHF reectors (two pieces, one top and

one bottom) in the self-locking clamp completed

on step 6 by inserting the end of the receptor

without the grey plastic cap on it and with the black

plastic locking mechanism in an upward position

(unlocked).

Once the reectors are fully seated in the clamp (all

the way to the bottom of the slot), lock them in place

by rmly pressing down on the black plastic pieces

An audible “click” will be heard when the reectors

are securely locked in place.

L x2 UJ K

M x2

CLICK!

F x2 H x2

G x2

T x4 W x4

Mount the two black plastic locks Lon the second

rear receptor self-locking clamp Kbottom piece.

Locate the mounting hole on VHF reector

extension C, place self-locking clamp Jtop piece

lined up with the hole in Cand bottom piece K,

secure with bolt U(bolt Ugoes through Jand

threads into K).

Insert the end “c4” of the VHF reector extension C

into the end “a4” of main assembly A. Secure them

with bolt Sand nut W.

Note: Tighten the nut Wuntil the square carriage

head of the bolt Ssinks into the aluminum and the

bolt head sits ush with the boom. The bolt base will

bite into the aluminum, securing the joint.

Place the NVHF reectors (two pieces, one top and

one bottom) in the self-locking clamp by inserting

the end of the reector without the grey plastic cap

on it and with the black plastic locking mechanism

in an upward position (unlocked).

Once the reectors are fully seated in the clamp (all

the way to the bottom of the slot), lock them in place

by rmly pressing down on the black plastic pieces

An audible “click” will be heard when the reectors

are securely locked in place.

L x2 U

N x2

CLICK!

(c4)

(a4)

Skip this step if using an already terminated coaxial

cable.

When using the provided weather boot and twist-on

connector on an unterminated coaxial cable, slide

the weather boot Qonto the coaxial cable and

properly terminate and t the twist-on connector

Pto the coaxial cable.

Pass the cable with the connector through the 2nd

slot in the lower reector.

P Q

9/32”

(7mm)

1/8”

(3mm)

2022 © Copyright, Televés S.A.U.

Televes USA LLC. Norfolk Tech Center 16596 E. 2nd Avenue Aurora, CO 80011 televes.usa@televes.com www.televes.com

Screw connector Ponto the dipole assembly

Oand tighten with a 7/16th wrench but do not

overtighten, then slide the weather boot Qover

the connector as far as it will go.

Insert the dipole assembly Ointo the antenna

orange junction box, sliding it through the guide

slot to the point where you will hear an audible

“click” indicating the dipole is latched into place and

fully seated in the main body of the antenna.

Visually check the dipole once installed to make sure

there are no gaps and that it did fully seat

Ensure that the longest boom is assembled to be

the top of the antenna as shown in the diagram. The

tilt/elevation adjustment on the mounting clamps,

shown in the diagram, allows for adjustment of the

vertical angle of the antenna as needed for optimum

reception. Starting from a horizontal position, use

the mounting clamps to adjust tilt/elevation if

needed for better antenna adjustment and to aim

over nearby obstacles.

The long booms are the front of the antenna, as

shown in the diagram, and should be pointed

generally, in the direction of the TV transmitter

towers. Adjusting the antenna slightly either left or

right of the direction of the TV transmitter towers

may actually yield better performance as it may

reduce some unwanted interfering signals.

CLICK!

Release the shackles from the mast clamps Gby

removing and saving the shackle and nuts. Place the

antenna assembly on the mast (not included) and

proceed to replace the shackles and tighten the nuts

to attach the assembly to the mast.

The “elevation screws” will allow you to adjust the

antenna elevation (level, up or down to optimize the

installation). Be sure to tighten these screws once

the desired antenna position is obtained.

Elevation screws

FINAL NOTES:

- Following the provided instructions, connect the

included power supply to the antenna using the

leftmost connector (closest to wall power) with an

appropriate length of 75 ohm coax, RG-6 or larger is

recommended. Make sure than any device installed

between the power supply and the antenna, such as

a splitter, is DC power passing. The two connectors on

the right of the power supply are for connecting your

TV’s and/or coaxial distribution.

- It may be necessary to alternate adjustments between

left and right and then tilt, several times in order to

achieve peak signal reception for the largest number

of desired channels.

- The antenna will work in an un-amplied, pass-through

mode, if the power supply is not connected or power

fails to reach the antenna for any reason. However, it is

recommended to always use the antenna with power

applied in order to activate the industry leading,

TForce automatic gain preamp that is built in to the

antenna.

- Always be sure to follow all local, state, and national

electric codes. Seek the assistance of a local

professional if needed.

TOP of Antenna

The longest boom is the TOP

part of the antenna.

FRONT of Antenna

Aim this end TOWARDS

TV transmitting towers.

BACK of Antenna

Aim this end AWAY from

TV transmitting towers.

Inhaltsverzeichnis

Andere Televes Antenne Handbücher

Televes

Televes DATBOSS MATV 149983 Bedienungsanleitung

Televes

Televes Ellipse Bedienungsanleitung

Televes

Televes DATBOSSMIX 149484 Bedienungsanleitung

Televes

Televes INNOVA BOSS Bedienungsanleitung

Televes

Televes TFORCE 108380 Bedienungsanleitung

Televes

Televes T.0X Series Bedienungsanleitung

Televes

Televes 4G NOVA Bedienungsanleitung

Televes

Televes 650 Bedienungsanleitung

Televes

Televes Omni-Nova Boss Bedienungsanleitung

Televes

Televes TURBOT 1332 Bedienungsanleitung

Televes

Televes DIGINOVA 1441 Bedienungsanleitung

Televes

Televes MIMO evoca TV-130990 Montageanleitung

Televes

Televes 108320 Bedienungsanleitung

Televes

Televes MATV DAT75HDBOSS Bedienungsanleitung

Televes

Televes DAT HD Boss 790 Bedienungsanleitung

Televes

Televes Evoca 130990 Bedienungsanleitung

Televes

Televes 800 Bedienungsanleitung

Televes

Televes 149981 Bedienungsanleitung

Televes

Televes DAT 790 HD BOSS LR Bedienungsanleitung

Televes

Televes INNOVA BOSS MIX Bedienungsanleitung

Televes

Televes Ellipse Bedienungsanleitung

Televes

Televes DINOVABOSSMIX Bedienungsanleitung

Televes

Televes 5226 Bedienungsanleitung

Televes

Televes 144110 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung