Televes TOX Series Bedienungsanleitung

HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP

Ref. 563805

QUICK INSTALLATION GUIDE

www.televes.com

Safety instructions

Caution Statements

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliers)

that produce heat.

9. Only use attachments/accessories specied by the

manufacturer.

10. Use only with the cart, stand, tripod, bracket, or table

specied by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

11. Refer all servicing to qualied service personnel. Servicing

is required when the apparatus has been damaged in any

way, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

Warning

Apparatus shall not be exposed to dripping or splashing and

no objects lled with liquids, such as vases, shall be placed

on the apparatus.

Safe operation

Should any liquid or object fall into the equipment, please

refer to qualied personnel for service.

Safe installation

Ambient temperature should not be higher than 95°F.

Do not place the equipment near heat sources or in a highly

humid environment.

Do not place the equipment in a place where it can suer

vibrations or shocks.

Please allow air circulation around the equipment.

Do not place naked ames, such as lighted candles on or

near the product.

Simbology

Equipment designed for indoor use.

The equipment complies with the CE mark

requirements.

This symbol indicate the maximum and minimum

temperature limits at which the equipment shall be

used.

DECLARACIÓN DE CONFORMIDAD DECLARATION OF CONFORMITY DECLARAÇÃO DE CONFORMIDADE DECLARATION DE

CONFORMITE DICHIARAZIONE DI CONFORMITÀ DEKLARACJA ZGODNOŚCI KONFORMITÄTSERKLÄRUNG ΠΙΣΤΟΠΟΙΗΤΙΚΟ

ΣΥΜΜΟΡΦΩΣΗΣ FÖRSÄKRAN OM ÖVERENSSTÄMMELSE ДЕКЛАРАЦИЯ СООТВЕТСТВИЯ بيان المطابقة

https://doc.televes.com

HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP

Description of connectors

Front view

LED indicators

Rear view

1.- ASI input

2.- ASI output

3.- Power connectors

4.- Ethernet connector

5.- Ethernet connector

6.- Programmer connector

7.- RF loop through input

8.- RF output

1.- YPbPr component input. Channel 1

2.- Closed Caption (CC) input. Channel 1

3.- Analog (L/R) audio input. Channel 1

4.- HDMI input. Channel 1

5.- SPDIF digital optical audio input. Channel 1

6.- SPDIF digital coaxial audio input. Channel 1

7.- SPDIF digital coaxial audio input. Channel 2

8.- SPDIF digital optical audio input. Channel 2

9.- HDMI input. Channel 2

10.- YPbPr component input. Channel 2

11.- Closed Caption (CC) input. Channel 2

12.- Analog (L/R) audio input. Channel 2

Front LED alarms

TEMP

Color Internal temp Comment

Solid green Normal Safe

Slow blink orange High Warning

Fast blink red Very High Danger

CH1 – CH2

Color Channel status Comment

O Disabled Channel disabled

Solid green Lock Input locked and unit encoding audio/video.

Solid red Unlock Input unlocked and unit not encoding audio/video.

Blinking red Boot Unit starting up.

OUTPUT

Color Output mode Comment

Solid green Normal Output RF channel is ON, broadcasting audio/video (normal mode).

Slow blinking green Carrier wave, null, or muted Output RF channel is OFF or in an alternate signal mode.

Solid orange/red Normal Cong bitrate doesn’t t in output

LOOP

Color Output loop status Comment

Solid green ON Output loop-through enabled. Units may be daisy-chained using the internal combiner.

O OFF Output loop-through disabled. Units must be combined using an external combiner.

Back LED indicators A/V inputs Indicate the currently selected audio and video inputs and where the input signals should be connected.

Installation

1. Install all units in the rack and connect them as shown. Each P.S.U.

can power a maximum of 6 units, except in the case of using video

resolutions of 1080p, in which only 5 units can be powered.

HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP

Fig. 1

2. Connect the audio and video input signals to the back of the modules.

Fig. 2

3. If a network that provides IP addresses through DHCP is available,

connect the encoders to the network as shown in g. 3. If such a

network is not available, then a computer will need to be connected

as shown in g. 4.

HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP

Fig. 3

4. Power on the units.

HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP

DIRECT NETWORK

CONNECTION

IP value = 172.20.0.2

netmask = 255.0.0.0

gateway = 172.20.0.3

Fig. 4

5. Connect the programmer to each unit and set a unique number in

the “# ID” eld according to the order of installation of the units in

the rack.

HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP

DIRECT NETWORK

CONNECTION

IP value = 172.20.0.2

netmask = 255.0.0.0

gateway = 172.20.0.3

Fig. 5

6. Connect the programmer to a unit, usually the rst one, and read

the IP address.

Each unit can work as a master controller for the other units. All units

can be congured by connecting to only one.

HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP

Fig. 6

7. If a network was connected in Step 3 then proceed to step 8. If not,

set the address of you computer as follows:

IP value = 172.20.0.2

netmask = 255.0.0.0

gateway = 172.20.0.3

NOTE: The default factory conguration of the units has an IP address in

this range (it should be dierent for each unit). If a unit was ever

provided an address before, manually or through DHCP, this unique

address may no longer exist. Resetting to IP factory defaults, will

return the original unique private address though.

8. In your web browser, enter the IP address from Step 6 as the URL.

A login prompt will appear. By default the parameters are:

Password: encoder

The Status > Summary page ( g. 7) should appear as the rst page.

This provides a summary of all the units installed in the network and the

units will be sorted by the number entered in Step 5.

Fig. 8 shows an example of a detailed status page.

9. Congure all units:

Select “CONFIGURATION”. This page has 5 options, INPUT, TRANSPORT,

OUTPUT, IP and NETWORK, shown in gures 9 to 14.

The last column of each conguration page is“Select”. Any changes made

will be saved only in the units with the “Select” option checked when

you click “Apply Selected” is applied to the ve tabs that exist under the

“Conguration” menu.

Some items have a choice of automatic conguration. For example, the

Network Conguration page allows you to change the number assigned

in step 5 of the installation process.

The “Auto” option will request conrmation if the parameters of all units

set in step 5 have been changed. The order will probably not correspond

with the position of the units in the rack.

9.1 INPUT

Conguration of the physical audio and video inputs. It

is possible to downscale the input resolution, modify the

video codec (MPEG-2 or H.264) or choose between frame

or eld encoding. If the input resolution is 1080p60/50 and

the video is being encoded in MPEG-2 it is necessary to set

the “Max Output Resolution” to 1080pHR. and frame/eld

encoding to “frame”. In this setup the output resolution will

be 1080P30/25.

Fig. 7 - Status > Summary

Fig. 8 - Status > Detailed

Fig. 9 - Input

Note: Resolution/Framerate will indicate the output video resolution only if it is dierent form the input one.

9.3 OUTPUT

Setting the RF output channel. The unit will restart if you switch

between QAM A and QAM B.

Fig. 11 - Output

9.4 IP

The unit can work in 3 dierent IP modes: Input, Output and

Disabled.

Input: The unit needs to be set in Input mode and have the IP

addresses, ports and standard (DVB or ATSC) congured.

Multicast and Unicast IP addresses are allowed.

These parameters can be modied on the IP tab (g. 12) and then

click “ Apply Selected”

Fig. 12 - IP

Fig. 13 - IP (2)

9.2 TRANSPORT

Changing the parameters of the output Transport Stream. The

TS ID, SID and VCNs of each service shall not overlap with those

of another service the same unit.

Fig. 10 - Transport

It is not possible to congure two equal IP adresses and ports,

the Web will warn you that it is not a valid conguration and will

not let you apply settings.

Pressing the “Select” button associated to each IP address, a

window with the available services will appear.

If no services are shown wait until the end of the scan.

Select the services to transmit through RF paying attention to the

free output bitrate and click on“Store Changes”.

Finally, to apply the conguration, click “Apply Selected”. The

selected services will appear in the “Transport” tab next to the

services of the physical inputs.

Output: To stream the services of the physical inputs via IP,

the unit must be set in Output mode and have the IP addresses,

ports, IP output type (SPTS or MPTS) and standard (DVB or ATSC)

congured. Multicast and Unicast IP addresses are allowed.

In SPTS mode, the physical input 1 will be streamed through the

IP1 and physical input 2 through the IP2.

In MPTS mode, the two physical inputs will be streamed through

a single IP.

If any of the physical inputs are disabled, the corresponding IP

service will not have transport.

9.5 NETWORK

Conguring network options. Both the IP address and the

networkmask may only be changed if DHCP mode is disabled

(g. 14).

10. Complete conguration window:

To change any encoder value from a single window, select

“CONFIGURATION”. Click on the name of the unit and the page shown

in gure 15 is displayed. From this page, you can modify any parameter

settings for the selected unit.

Fig. 14 - Network

Fig. 15 - Advanced conguration

- OUTPUT -

SELECT OUT

LEVEL

- OUTPUT -

SELECT OUT

LOOP MODE

LOOP

- UNIT -

MODE

DHCP ON

- # ID -

0001

- TEMP -

NOW: 46 F

MAX: 86 C

- OUTPUT -

SELECT OUT

FREQ/CHAN

CATV CHANNEL

- OUTPUT -

SELECT OUT

CHANNEL

2 = 57MHz

QAM A

QAM B

563805

- OUTPUT -

SELECT OUT

INTERLEAVING

<128.1>

* Next page

IP1 SERV

1/2

IPServ1

ORIG. NAME

1/1 IP1

IPServ1

SID 1/1

IP1 IPServ1

00001 00003

INPUT 1/2

Selected

INPUT IP

Selected

(RX Mode Only)

IP MENU*

REMAP NAME

1/1 IP1

IPServ1

VCN 1/1

IPServ1

CVCT2

VCN 1/1

IPServ1

Major: 2

Minor: 3

- INPUT 1 -

VIDEO CONF>>

OUT: H.264

12.00 Mbps

- INPUT 1 -

MAX RESOLUT.

OUTPUT

AUTO

- INPUT 1 -

FIELD ENCOD.

OUTPUT

FIELD

- INPUT 1 -

- CC -

-CHANNEL NUM-

MODE: CUCT 2

- INPUT 1 -

CUCT 2

MAJOR -> 2

MINOR -> 2

- INPUT 1 -

VIDEO CONF>>

PROF. LEVEL

AUTO(4.0)

- INPUT 1 -

CC: OFF

- QAM MODE -

QAM B

- OUTPUT -

SELECT OUT

MODULATION

256 QAM

- OUTPUT -

SELECT QAM

BAUD RATE

5.360 Kbaud

- OUTPUT -

SELECT OUT

MODE

NORMAL

- OUTPUT -

TS ID

0x0001

H.264 enconding only

QAM B only

QAM B 1.01.04

SW 1.04.0269

Menu ow chart

For programming Unit operation

Enable edit mode /

Position cursor

(in edit mode) /

Disable edit mode.

Change section /

Save parameters

(press and hold

for 3 sec.)

Change menu /

Modify value

(in edit mode)

PORT NUMBER

OUTPUT 1

01100

PORT NUMBER

OUTPUT MUX

01100

- OUTPUT IP -

OUTPUT 1

ENABLE

- STANDARD -

OUTPUT 1

ATSC

- STANDARD -

OUTPUT 1

ATSC

- STANDARD -

OUTPUT 2

ATSC

- INPUT IP -

INPUT 1

ENABLE

- STANDARD -

INPUT 1

ATSC

- OUTPUT IP -

OUTPUT MUX

ENABLE

- OUTPUT -

IP FORMAT

SPTS

- IP MODE -

RX MODE

- # ID -

0001

- N PACKETS -

OUTPUT 1

- N PACKETS -

OUTPUT MUX

-IP ADRESS -

OUTPUT 1

225.000.

001.001

-IP ADRESS -

INPUT 1

225.000.

001.004

-IP ADRESS -

OUTPUT MUX

225.000.

001.001

- RTP -

OUTPUT 1

ENABLE

- RTP -

OUTPUT MUX

ENABLE

- RTP -

OUTPUT 2

ENABLE

- OUTPUT IP -

OUTPUT 2

ENABLE

- N PACKETS -

OUTPUT 2

-IP ADRESS -

OUTPUT 2

225.000.

001.002

PORT NUMBER

OUTPUT 2

01200

SELECT

DEFAULT

SETTINGS

Hold key

PORT NUMBER

INPUT 1

1300

PORT NUMBER

INPUT 2

1400

- RTP -

INPUT 1

ENABLE

- RTP -

INPUT 2

ENABLE

- INPUT IP -

INPUT 2

ENABLE

-IP ADRESS -

INPUT 2

225.000.

001.005

RX MODE DISABLED

TX MODE

SPTS MPTS

- STANDARD -

INPUT 2

ATSC

IP menu

For programming Unit operation

Technical specications

Reference 563805

INPUTS

VIDEO Connectors 2 sets - 3x RCA for Video (Y, Pb, Pr)

AUDIO Connectors

2 sets - 2x RCA for Analog Audio (L, R)

2 sets - 1x RCA for Digital Audio

2 sets - 1x Toslink for Digital Audio (Optical)

VIDEO + AUDIO Connectors 2 sets - 1xHDMI

CLOSED CAPTIONING Connectors 2 sets - 1x RCA (CC in)

ASI

Connectors 1x BNC

Format DVB-ASI

Standard ETSI EN 50083-9

IP Connectors 2x RJ45 (Switch Gigabit)

Formats SPTS or MPTS (UDP/RTP)

ENCODING

PROFILE

VIDEO

Output Format MPEG-2 / H.264(4.0, 4.1, 4.2, 5.1, 5.2)

Input Resolution 480i, 480p, 576i, 576p, 720p, 1080i &1080p (1)

Supports auto-scan for input resolution

Input Framerate 50Hz, 60Hz (all input Resolutions), 24Hz (only 1080p Input Resolution)

Output Resolution Same as input (Auto) or maximum selected output resolution

Output Aspect Ratio 4:3, 16:9, and pass through

Output GOP 10, 12, 15, 16, 18, 20, 24 or 30

Output Transport rate Variable

Output Video bit rate Variable

AUDIO

Output format Dolby® Digital AC-3 or MPEG1 Layer 2

Output Sampling rate kHz 48, 44.1

Output bitrate Variable

CLOSED CAPTIONING Format EIA-608, EIA-708 (2)

OUTPUT

QAM

Connectors 1x “F” Female

Modulation standards ITU-A: 16, 32, 64, 128, 256, 512, 1024 QAM

ITU-B: 64, 256 QAM

Frecuency Range MHz 5 - 1002 (supports return path applications)

Channel plans CATV STD, T_CHANNELS, Broadcast, Frequency

Max output level dBmV +55 (+43 with loop-through)

MER dB >40 (typ)

Spurious dBc -60

Impedance Ω 75

I/Q Phase Error º <1

I/Q Amplitude Imbalance % <1

ASI Connectors 1x BNC

Format DVB-ASI

IP Connectors 2x RJ45 (Switch Gigabit)

Format SPTS or MPTS (UDP/RTP)

PSI PARAMETERS

Transport Stream ID Editable

Original Network ID Editable

Network ID Editable

Virtual Channel Number Editable

NIT Version Manual / Automatic

SDT Version Manual / Automatic

Network Name Editable

Service PID Editable

Service Name Editable

Service ID Editable

MONITORING / CONTROL

Local control Full conguration with LCD handheld programmer

Local monitoring

LOOP status LED

QAM status LED

TEMP status LED

CH1/CH2 status LEDs

Ethernet status LEDs

Remote monitoring Centralized web based remote control, management, alarms, and software upgrades

Control Daisy-chain integrated ethernet switch

GENERAL

Power supply V 24

Power disipation W <22.8

Operating Temperature ºF / ºC 32 to 95 / 0 to 35

The technical specications are dened for an ambient temperature of 35 ºC (95 ºF). It shall always be installed with forced ventilation.

(1) 1080p resolution is only supported with MPEG-4 video codec.

(2) For correct CC operation at the output, the maximum output resolution is set to “Auto”or the input and output resolution are both“i”or both“p”at the same framerate.

Andere Handbücher für TOX Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Televes Modulator Handbücher

Televes

Televes 585981 Bedienungsanleitung

Televes

Televes T.0X Series Bedienungsanleitung

Televes

Televes T.OX TWIN QPSK-PAL C Bedienungsanleitung

Televes

Televes TOX Series Bedienungsanleitung

Televes

Televes 5806 Bedienungsanleitung

Televes

Televes 5504 Bedienungsanleitung

Televes

Televes 585901 Bedienungsanleitung

Televes

Televes 5858 Bedienungsanleitung

Televes

Televes COFDM-PAL CI Bedienungsanleitung

Televes

Televes 554912 Bedienungsanleitung

Televes

Televes COFDM-PAL Bedienungsanleitung

Televes

Televes TOX Series Bedienungsanleitung

Televes

Televes 5806 Bedienungsanleitung

Televes

Televes 585981 Bedienungsanleitung

Televes

Televes T.0X COFDM-QAM CI Bedienungsanleitung

Televes

Televes TDT+ Bedienungsanleitung

Televes

Televes QPSK-PAL Bedienungsanleitung

Televes

Televes TOX Series Bedienungsanleitung

Televes

Televes 585915 Bedienungsanleitung

Televes

Televes 585910 Bedienungsanleitung

Televes

Televes T.0X Series Bedienungsanleitung

Televes

Televes TOX Series Bedienungsanleitung

Televes

Televes 554501 Bedienungsanleitung

Televes

Televes T.0X Series Bedienungsanleitung

Beliebte Modulator Handbücher anderer Marken

axing

axing AVM 5-00 Bedienungsanleitung

IKUSI

IKUSI MAC-HOME HD Bedienungsanleitung

Wisi

Wisi MINI OM 10 Bedienungsanleitung

RCA

RCA CRF910 Bedienungsanleitung

Pico Macom

Pico Macom PM45 Bedienungsanleitung

FTE Maximal

FTE Maximal MODIG AIR Bedienungsanleitung

Thor Broadcast

Thor Broadcast H-IP-32RF Bedienungsanleitung

Delphi

Delphi SA10003 Bedienungsanleitung

Elan

Elan MOD3000 Bedienungsanleitung

ClearView

ClearView SD4260 Bedienungsanleitung

Crucial Audio

Crucial Audio Die Gotterdämmerung Bedienungsanleitung

Pioneer

Pioneer CD-V61FM Bedienungsanleitung

Newtec

Newtec M6100 Bedienungsanleitung

ProTelevision

ProTelevision PT 5780 Bedienungsanleitung

Argent Cables

Argent Cables HD DVB-T MODULATOR Bedienungsanleitung

SSS Siedle

SSS Siedle BVM 650-0 Bedienungsanleitung

Multiplex

Multiplex CHANNEL PLUS 5615 Bedienungsanleitung

Hides

Hides UT-210 Bedienungsanleitung