Teltonika WirelessCOM/G10 Bedienungsanleitung

Address: Žirmūnųg. 27, Vilnius LT-09105,

Tel.: +370 5 2127472,

Fax: +3705 276 1380, E-mail: info@teltonika.lt

Teltonika WirelessCOM/G10

User’s Manual 4.0.1

TABLE OF CONTENTS

Teltonika WirelessCOM/G10.............................................................................................................. 1

User’s Manual 4.0.1............................................................................................................................. 1

TABLE OF CONTENTS .................................................................................................................... 2

1. ATTENTION............................................................................................................................... 3

2. SAFETY MEASURES................................................................................................................ 4

3. BASIC INFORMATION ............................................................................................................ 5

3.1 About this document.................................................................................................................. 5

3.2 Legal Notice .............................................................................................................................. 5

3.3 Contacts ..................................................................................................................................... 5

3.4 Acronyms................................................................................................................................... 5

4. PACKAGE CONTENTS ............................................................................................................ 6

5. FEATURES................................................................................................................................. 7

6. INTRODUCTION....................................................................................................................... 8

6.1 Wired Solution........................................................................................................................... 9

6.2 Wireless solution using WirelessCom/G10............................................................................. 10

7. CONFIGURATION .................................................................................................................. 11

7.1 Preparing WirelessCOM/G10 configuration........................................................................... 11

7.2 PC setup................................................................................................................................... 11

7.3 Entering into configuration mode............................................................................................ 12

7.4 Command set ........................................................................................................................... 12

7.5 Configuration parameters ........................................................................................................ 15

7.6 Configuration through GPRS and CSD................................................................................... 18

7.7 Configuration through SMS .................................................................................................... 19

7.8 SMS details.............................................................................................................................. 20

7.8 SMS formats............................................................................................................................ 21

8. TECHNICAL SPECIFICATION.............................................................................................. 23

8.1 General..................................................................................................................................... 23

8.2 LED indications....................................................................................................................... 23

8.3 Operating parameters............................................................................................................... 24

8.4 Mechanical characteristics....................................................................................................... 24

8.5 Version numbering .................................................................................................................. 25

8.4 WirelessCom/G10 customization............................................................................................ 25

9. ENDING.................................................................................................................................... 26

APPENDIX I ..................................................................................................................................... 27

APPENDIX II.................................................................................................................................... 29

1. ATTENTION

All wireless devices for data transferring are susceptible to

interference, which could affect performance

Only qualified personnel may install or repair this product

The device is not water-resistant. Keep it dry.

Do not mount or serve device during a thunderbolt.

2. SAFETY MEASURES

This section will provide guidelines on how to use WirelessCOM/G10 device safely. We

suggest you to adhere to following recommendations so as to avoid any damage to person or property.

You have to be familiar with the safety requirements before you start using the device!

Installation and technical support of the device can be performed

only by a qualified personnel or a person who has enough

knowledge about this device and safety requirements.

The device requires 9 V power supply. Available power supply source range is 6 V up to

15 V, power up to 3500mW.

The PC and power supply source to which the device is

connected should satisfy LST EN 60950-1 standard.

WirelessCOM/G10 modem can be used on first (Personal

Computer) or second (Notebook) computer safety class.

To avoid mechanical damage of the device, it is recommended to transport the device

packed in damage-proof pack.

While using the device, place it such that the LEDs are visible to the user. It’s because

these LEDs provide information about the working modes and conditions of the device.

Signal level of the WirelessCOM/G10 depends on the environment in which it is

working.

If the device fails to work properly only qualified personnel may repair this product. We

recommend to disconnect the device and forward it to repair centre or to the manufacturer. The

modem does not contain any parts which can be replaced.

At the installation site, supply circuits must have protective devices (bipolar release

device) which provide protection from short-circuit and wrong ground installation. The power of

connected device should satisfy power of release device. The interstice between contacts should be no

less than 3mm. Power supply network should be installed near the device on an easily accessible place

3. BASIC INFORMATION

3.1 About this document

This manual describes the Teltonika WirelessCOM/G10 hardware, configuration and

operation. The manual would help the users to deploy, configure and operate WirelessCOM/G10.

3.2 Legal Notice

distribution or storage of part or all of the contents in this document in any form without the prior

written permission of TELTONIKA Ltd is prohibited.

Other products and company names mentioned herein may be trademarks or trade names of

their respective owners.

3.3 Contacts

If you face any problems related to the device, which you are not able to solve by

yourself, please contact your local distributor.

3.4 Acronyms

APN Access Point Name.

AC/DC Alternating Current/Direct Current

CSD Circuit Switched Data.

GPRS General Packet Radio Service.

GSM Global System for Mobile communications.

PC Personal Computer.

M2M Machine-to-Machine.

ISP Internet Service Provider.

PIN Personal Identification Number.

SIM Subscriber Identity Module.

SMS Short Message Service.

TCP/IP Transmission Control Protocol/Internet Protocol.

4. PACKAGE CONTENTS

Teltonika WirelessCOM/G10 is packed in a box and contains all the accessories required for

normal operation:

ªWirelessCOM/G10.

ªAC/DC adapter.

ªRS232 serial cable.

ªExternal GSM antenna.

ªCD with User Manual.

ªLeaflet “Quick Start Guide”.

If any of the components are missing please contact your local distributor.

Note: The manufacturer does not supply the SIM card, which is mandatory for setting up a

connection to the GSM network! The SIM card may be purchased from your GSM (mobile) service

provider!

5. FEATURES

•Provides transparent GPRS/CSD connection

•Receive SMS alerts when exceptions occur in device

•No drivers required, hence works with any device/machine/equipment/computer

•Simple and informative configuration menu

•Configurable through any terminal software

•Hardware reset from DTR pin (optional)

•Device is remotely configurable through GPRS/CSD/SMS

•Access only through authorized phone numbers (for CSD and SMS)

•Up to 5 configurable authorized phone numbers

•Auto PIN feature, no need to enter SIM card PIN after restart

•Password protected configuration

•Dual colour LED indication for various states of device (Up to 9 states)

•Supports various data formats (8N1,8N2,8E1,8O1,7E1,7O1)

•Firmware update possibility

•CHAP/PAP authentication supported

•CE certified

6. INTRODUCTION

Many times a need is felt to upgrade software of a remotely situated device/machine, or

monitor its parameters, or receive warnings on malfunctioning to a remotely situated server. Taking

advantage of the large mobile networks and their supporting GPRS features, it is now possible to

connect devices in the field back to a central server simply and cost-effectively. Using wireless cellular

technology, serial devices such as PLC, Modbus, RFID scanners, data loggers, electricity meters,

pumps, valves, POS (Point-Of-Sales) terminals and such other equipments can be connected to a

central processing server without the requirement for cables to be installed. All you need is a device

which has a serial port, and WirelessCom/G10. Just configure and connect WirelessCom/G10 to your

device/machine and your device/machine would easily turn it into a device which can be accessed from

any remotely located server.

WirelessCOM/G10 is exactly what its name says; it is a wireless COM port. When

WirelessCOM/G10 is connected to any equipment with COM/RS-232 ports, it just replaces the

physical cable (RS232) connection by wireless GSM network. This means, the length of RS232 cable

would be as long as a GSM network. Thus, as far as a GSM network is available, this device will be

accessible from any part of the world. In simple words, WirelessCom acts as a bridge between serial

port and GPRS. All the information coming through GPRS/CSD is sent to serial port and all the

information coming on serial port is sent to GPRS/CSD. In short there is a transparent connection

between WirelessCom and the server/PC (for example) without any physical limits.

WirelessCom is basically an intelligent pre-programmed modem for making GPRS/CSD

connections and handle the exceptions arising during the process of making connection. Thus you

don’t need an external microcontroller to control WirelessCom using AT commands. All you need is to

configure WirelessCom (the configuration parameters are explained in later sections) and it will

automatically make connections using the configured bearer (GPRS/CSD). If anything goes wrong, for

example GPRS activation failed/CSD call could not be established/GPRS connection could not be

Physical contact

Figure 6.1

RS232 connection

6.1 a)

INTERNET/

CSD call

Virtual contac

6.1 b)

established/CSD call was not answered, you would receive SMS indicating the errors and the

concerned parameters.

Once configured, connect (physically) WirelessCom to the serial port of your remote

device/machine and you would be able to access your device remotely through GPRS/CSD.

Additionally, if you want to change the configuration parameters of WirelessCom you can do it

remotely using GPRS/CSD/SMS.

The next section would explain 2 scenarios 1) Typical wired connection which is being

used by most of the users. 2) A solution which would turn your wired connection into a wireless

solution so that you would have remote access, control and monitoring of your device/machine

through GPRS/CSD.

6.1 Wired Solution

A typical wired setup includes a device/machine with a RS232 port connected to the

serial port of the PC using a normal RS232 cable, refer fig 6.1. The user then launches some proprietary

software which came with the device/machine (or it can be a terminal software) and connects the

software to the same serial port to which device/machine is connected, refer fig 6.1 (b). Thus a

connection between device/machine and the software has been established. Now the user can

configure, operate, collect data, program the device/machine and perform such various operations. In

short the user is in total control of the device/machine.

PC/Serve

RS232 cable

(Physical connection)

Hardware serial

port of PC

Proprietary software

running on PC

RS232 cable

(Physical connection)

6.1 (a)

6.1 (b)

Figure 6.1: Typical wired setup

6.2 Wireless solution using WirelessCom/G10

A typical setup may look as shown in figure 6.2, WirelessCom may be connected

(physically) to any device, machine (which has a RS232 port) located in a remote place and the server

computer would be present at the company/home. Through various parameters settings (server ip,

server port, apn……) present in WirelessCom, it would be configured to connect to the server.

On the server would be running two software’s,

a) TCP-to-Serial software/Telnet/TCP port software:TCP-to-serial software is only required if

you have dedicated (proprietary) software which you use to control/configure/read/write your device.

This software is used to create a virtual serial port on your computer. This port will appear as a

hardware port for your computer. The main function of this software is to direct all the data coming on

the TCP port to the virtually created serial port.

If you are using simple terminal software for interacting with your device, in that case you

can use any Telnet software* (Microsoft Telnet) or a TCP port communication software like Netcat

and set a TCP/IP port in listening mode.

*Refer to APPENDIX II for more details

b) Proprietary software:This software (can be even a free terminal software) is used to make

a connection from PC to the device/ machine using normal serial port (as explained in the scenario of

wired solution). Launch this software and connect it to the virtually created serial port. The setup is

done and your proprietary software is now connected to your device/machine remotely through GPRS.

PC/Server

Virtual serial port

(TCP-to-Serial

software)

Proprietary

software

running on PC

INTERNET

Ethernet/GPRS/Wireless

Your device

WirelessCom/G10

Serial connection

(Physical)

Figure 6.2: Wireless setup

Telnet software with TCP/IP

port in listening mode

Inhaltsverzeichnis

Andere Teltonika Netzwerk-Hardware Handbücher

Teltonika

Teltonika Maxview MXL050 Roam Montageanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung