Tennsco RXHS-962484 Bedienungsanleitung

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE

PK-2871018

Models: RXHS-962484, RXHS-962496,

Heavy-Duty Reinforced High Capacity Shelving

RXHS-963684, RXHS-963696

Extra shelves are also available (RXHS-wwdd).

Tennsco LLC.

, Dickson, TN 37056-1888 • (866) 446-8686

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.

For safety, wear a pair of work gloves when assembling or performing any maintenance on the unit.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in

the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

LOAD CAPACITIES

PER SHELF LEVEL*

96w x 24d

96w x 36d

2600 lbs.

UNIT SIZE WT. CAPACITY

*Total Unit Capacity not to exceed 13,000 lbs.

ASSEMBLY OF HEAVY-DUTY HIGH CAPACITY SHELVING

Two people are recommended for assembly. Approximate assembly time: 35-45 minutes per section.

The reference numbers used throughout this sheet refer to the illustration on the back cover.

This is to help you to identify the various parts as they are mentioned.

4. Lay the bottom steel decking (Ref. No. 6) on the shelf supports so that

the front and back edges overlap the front and back shelf supports.

1. With help from an associate, or using a wall for support,

create a unit end by connecting two SUR uprights together

(Ref. No. 1) with two front-to-back end shelf supports (Ref.

No. 2), one at the top and one at the bottom. Be sure the

supports are fully seated in the slots. Repeat to construct a

second unit end.

2. Next, connect the two unit ends with two LRA left-to-right

shelf supports (Ref. No. 3) at the bottom and one LRC left-

to-right shelf support (Ref. No. 4) at the top, temporarily

leaving off one of the top left-to-right supports.

NOTE: The two LRA supports at the bottom have no return ange

on the bottom edge, while the LRC support have a return ange

at both the top and bottom.

3. Attach three front-to-back center shelf supports (Ref. No. 5) by

inserting the deck support keyhole slots over the rivets on the

supports and tapping them rmly into place.

IMPORTANT! All shelf

supports should be

inserted with the

return ﬂange on top,

as shown at right.

(This ﬂange is what the

shelves will rest upon)

NOTE: Inset is shown

from opposite side.

NOTE: One top

support is not inserted

until step 8.

LRA (bottom level only)

One return ﬂange on top.

LRC (all other levels)

Two return ﬂanges.

NOTE: Bolts are not needed to secure the deck supports on

the bottom shelf because it rests on the oor. All other levels

require these bolts to achieve maximum load capcities.

NOTE: Every fourth slot in the uprights has a at top to

help visually align the supports.

5. Attach shelf supports at the next desired shelf level.

Once the shelf supports are in place, attach three

front-to-back center supports as you did in step 3.

Lower the steel decking into place, as described in step 4.

NOTE: Be sure to bolt both the front

and rear of each shelf. This requires

six bolts per shelf.

7. Attach the remaining shelf supports and decking at the

desired shelf levels, completing one level at a time.

NOTE: Once all but the top shelf are in place, attach the

remaining left-to-right shelf support at the top level.

8. After attaching the top shelf and securing it with six

sets of bolts, your die rack unit is fully assembled and

ready for use.

6. Once the decking is in place, secure it to the shelf supports

with six sets of 1/4-20 x 5/8bolts and nuts (Ref. No. 6). Do

this by placing one bolt through each hole in the front and

rear of the shelf, making sure the bolt goes through the shelf

and shelf supports as shown below. Tighten securely.

REPLACEMENT PARTS

Steel Decking

(Ref. No. 6)

Front-to-Back Center

Shelf Support

(Ref. No. 5)

Front-to-Back

End Shelf Support

(Ref. No. 2)

Bolts and Nuts

1/4-20 x 5/8”

(Ref. No. 7)

Heavy

Upright Post

(Ref. No. 1)

Left-to-Right (LRA)

Shelf Support

(Ref. No. 3)

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.

However, should your unit contain missing or damaged parts, please contact your purchase location.

NOTE: Additional hardware may be included for replacement purposes.

Left-to-Right (LRC)

Shelf Support

(Ref. No. 4)

REF. NO. DESCRIPTION

1 Heavy Upright Post 4 SUR-84 SUR-84 SUR-96 SUR-96

2 Front-to-Back End Shelf Support 10 LRA-24 LRA-36G LRA-24 LRA-36G

3 LRA Left-to-Right Shelf Support 2 LRA-96 LRA-96 LRA-96 LRA-96

4 LRC Left-to-Right Shelf Support 8 LRC-96 LRC-96 LRC-96 LRC-96

5 Front-to-Back Center Shelf Support 15 SDS-24 SDS-36 SDS-24 SDS-36

6 Steel Decking 5 ZS-9624 ZS-9636 ZS-9624 ZS-9636

7 1/4-20 x 5/8” Bolts and Nuts AVAILABLE LOCALLY

PART NUMBERS

RXHS-962484 RXHS-963684 RXHS-962496 RXHS-963696

QTY.

49B287

Dieses Handbuch passt für folgende Modelle

Andere Tennsco Werkzeugaufbewahrung Handbücher

Tennsco

Tennsco WBD-25 Bedienungsanleitung

Tennsco

Tennsco Industrial Workbench with Hardwood Butcher Block... Bedienungsanleitung

Tennsco

Tennsco 1340397 Bedienungsanleitung

Tennsco

Tennsco MB-2-2542-MGY Bedienungsanleitung

Tennsco

Tennsco Industrial Workbench with Steel Top Bedienungsanleitung

Tennsco

Tennsco MB-3-2545 Bedienungsanleitung

Tennsco

Tennsco WB 3072 Series Bedienungsanleitung

Tennsco

Tennsco 3072 Bedienungsanleitung

Tennsco

Tennsco WBCK-3036 Bedienungsanleitung

Tennsco

Tennsco INDUSTRIAL WORKBENCH With Steel Top Bedienungsanleitung

Beliebte Werkzeugaufbewahrung Handbücher anderer Marken

Ryobi

Ryobi RWB03 Bedienungsanleitung

Husky

Husky H27CH5TR4BGK Bedienungsanleitung

Scheppach

Scheppach ts 2100 Bedienungsanleitung

DIVERSIFIED WOODCRAFTS

DIVERSIFIED WOODCRAFTS SHAIN GSB-6024 Bedienungsanleitung

Cassese

Cassese CS200 CART Bedienungsanleitung

Cornwell Tools

Cornwell Tools CTB360AKBK Bedienungsanleitung

Kendall Howard

Kendall Howard ESDW-9630-1000 Bedienungsanleitung

Lista

Lista Align Montageanleitung

Workzone

Workzone 99609 Bedienungsanleitung

Stanley

Stanley STST83800-1 Bedienungsanleitung

Homak

Homak PROFESSIONAL Series Systemhandbuch

Perel

Perel ROLLER SHUTTER STORAGE CABINET Bedienungsanleitung

Husky

Husky H5CH2R Bedienungsanleitung

BGS technic

BGS technic 4107 Bedienungsanleitung

Clarke

Clarke CWB1250 Bedienungsanleitung

Ryobi

Ryobi RWB02 Bedienungsanleitung

Husky

Husky H52CH6HDV3WHT Bedienungsanleitung

Sealey

Sealey PTB66004 Bedienungsanleitung