Tenways CGO800S Bedienungsanleitung
Installation
Manual
CGO800S
Tool Box check list.
Bike box
Battery Pack Tool Box
(1) Take your bike, tool box, and battery pack out of the box.
(2) Remove and recycle all wrapping materials.
01
Unwrap your TENWAYS E-bike.
10mm
Wrench
15mm
Wrench
3mm
Hex Key
4mm
Hex Key
5mm
Hex Key
Charger
Bicycle Pedals
LR
Phillips Head
Screwdriver
Front & Rear
Cycling
Pump
Adapter
2
(1)
Remove
Plastic
Covers
Twist the head of the handlebar so that it faces forward. (1) Remove the front wheel and the plastic protective covers on
both sides of the wheel.
Hold your e-bike with the kickstand down to facilitate the
next installation steps.
02 03
Rotate the head of the handlebar. Remove the front wheel.
(2)
You must remove the front wheel in the direction of the spokes to avoid
scratching them.
4 5
(1) (1)
Loosen the nut and remove the quick release lever. Secure the nut behind the head light with the 10mm Wrench,
and then loosen the screw with the 5mm Hex Key.
Remove the protective sheet from the brake clamps.
Put the nut back, and then slightly tighten it.
Use the 4mm Hex Key to remove the pre-installed screws
on the front fork joints, install the two support rods on the
joints, and then slightly tighten the screws here.
Manually adjust the height of the mudguard to the top
position, and then tighten all screws.
(2)
(2)
(3)
(3)
(4)
(4)
(5)
Remove all wrapping material from the quick release.
Remove the nut, and then hook the middle of the front
mudguard to the screw.
There is no need for you to fully tighten the nut at this time.
The protective sheet on the brake should be removed only at this step, and kept for future use.
Removing it too early could damage the brake caliper.
When installing the quick release spring, you should ensure that the orientation is the same as
when it was removed.
05
Install the front wheel mudguard.
0
4
Remove quick release from the front
fork. Pre-install it on the front wheel.
10mm
Wrench
15mm
Wrench
3mm
Hex Key
4mm
Hex Key
5mm
Hex Key
Keep wrapping materials and
protective sheet for future use.
Install the quick release on the front wheel in the direction shown in
the gure, and then tighten the nut.
6 7
(1)
(2)
(3)
Adjust the quick release lever to the open position. Install the front
wheel; make sure that the brake disc is in the middle of the brake
clamps.
Tighten the quick release nut, and then turn it to the closed position
as shown in the gure.
Push the e-bike back and forth and press the brake to check if the
front wheel wobbles. If so, please repeat step 2 until you feel enough
resistance when closing the quick release lever.
(4)
(5)
Turn the front wheel by hand and check if there are any signs
of scraping.
If yes, please follow the steps below to make adjustments:
Install the front wheel.
06
-
-
-
-
-
-
Use the 5mm Hex Key to slightly loosen the mounting screws of the
brake clamps to make sure that they can move slightly.
Press the front brake 3 to 5 times.
Hold the front brake and tighten the mounting screws of the brake
clamps.
Turn the front wheel by hand and listen for the sound of friction.
If there is friction, loosen the mounting screws of the brake clamps.
Manually adjust the position of the brake clamps to center the disc,
and then re-tighten the screws.
This step is extremely important, so please read carefully. This step is extremely important, so please read carefully.
3mm
Hex Key
4mm
Hex Key
5mm
Hex Key
8 9
Install the battery.Install the pedals.
(1) (1)
Separate the left and right pedals.
The right and left pedals are marked by an R and an L respectively.
The right pedal is used for the side with the crankset, while the left
one is used for the other side.
Tilt and clip the lower end of the battery into the battery slot,
and then press the upper end.
(2) You will hear a click when the battery is rmly seated.
07 08
Left Right
Tighten the right pedal clockwise and the left pedal
counterclockwise.
Please stop tightening the pedals if you feel a lot of resistance. If
this happens, align and reinstall the pedals.
(2)
(3)
10mm
Wrench
15mm
Wrench
10 11
Open the seat post clamp, adjust the saddle cushion to a suitable
height, and then lock the clamp.
Distinguish between the front reector and the rear one. The
rear reector is red, while the front one is white.
The height of the seat post cannot exceed the marked safety line.
(1) (1)
(2)
Use the Phillips head screwdriver to install the rear reector
to the seat post and the front one to the handlebar.
Adjust the height of the saddle cushion.
09 10
Install the reectors.
Phillips Head
Screwdriver
Front
Reector
Rear
Reector
12 13
(1) (1)
(3)
(3)
(4)
You can press and hold the On/Off button to turn on the panel. The panel displays the real-time speed by default after it is
turned on.
The panel will be turned off if you long press the On/Off button again
when it is on.
The battery percentage is displayed at the top.
The e-bike will automatically shut down if it is not used for more than
ten minutes.
M Botton
Speed Up
Speed Down
ON / OFF
Left-turn Indicator
Right-turn Indicator
Display panel
(2)
(2)
The default passcode is 0000.
You can press the M button 5 times to enter the operation interface. The PAS level is shown at the lower right corner of the panel
display, while TRIP (a specic distance in kilometers your e-bike
has traveled) and ODO (the total number of kilometers your
e-bike has traveled) are shown at the middle position.
Panel operations
How to turn on the panel. Panel display interface
11
M
14 15
(1)
You can long press the M button to switch from the TRIP and ODO
interface to the AVG and MAX interface.
(2)
The AVG and MAX interface shows the average speed and the
maximum speed.
How to switch between the main interfaces.
(1)
(3)
You can use the Up and Down buttons to select from 5
assistance modes.
PAS 0 is the default when the panel is turned on.
(2)
The 1st and the 5th PAS represent the lowest and the highest
power respectively.
Adjust the assistance.
16 17
(1)
Short press the RIGHT/LEFT turn indicator button to turn on the rear
turn signal on the RIGHT/LEFT side.
(2)
(3)
Press and hold the LEFT-TURN Indicator button for 2 seconds to turn
on the head light and tail light.
Press and hold the RIGHT-TURN Indicator button for 2 seconds to turn
off the head light and tail light.
How to use the head light and the tail light.
The e-bike will enter Assisted Pushing if you press and hold the
DOWN button for 2 seconds.
Assisted pushing.
This feature can only be used when you’re walking and pushing the e-bike.
18 19
Inhaltsverzeichnis
Andere Tenways Fahrrad Handbücher
