Terex S-60 J Bedienungsanleitung

Operator's Manual

Serial Number Range

S®-60 J

from S60JH-101

from S60JD-101

with

Maintenance

Information

Original Instructions

First Edition

Second Printing

Part No. 1283765GT

Operator's Manual First Edition • Second Printing

S®-60 J Part No. 1283765GT

Front Matter

Manufacturer:

Terex South Dakota, Inc.

500 Oakwood Road

Watertown, SD 57201, USA

EU Authorized representative:

Genie Industries B.V.

Boekerman 5

4751 XK OUD GASTEL

The Netherlands

Contents

Introduction........................................................... 1

Symbol and Hazard Pictorials Definitions............. 5

General Safety...................................................... 8

Personal Safety................................................... 11

Work Area Safety................................................ 12

Legend................................................................ 22

Controls............................................................... 23

Inspections.......................................................... 31

Operating Instructions......................................... 44

Transport and Lifting Instructions ....................... 57

Maintenance ....................................................... 60

Specifications...................................................... 64

First Edition: Second Printing, May, 2021

Genie and "S" are registered trademarks of Terex South

Dakota, Inc. in the U.S.A. and many other countries.

Complies with EC Directive 2006/42/EC

See EC Declaration of Conformity

First Edition • Second Printing Operator's Manual

Introduction

Part No. 1283765GT S®-60 J 1

Introduction

About this manual

Genie appreciates your choice of our machine for

your application. Our number one priority is user

safety, which is best achieved by our joint efforts.

This book is an operation and daily maintenance

manual for the user or operator of a Genie

machine.

This manual should be considered a permanent

part of your machine and should remain with the

machine at all times. If you have any questions,

contact Genie.

Product Identification

The machine serial number is located on the serial

label.

Serial label

(located under cover)

Serial number stamped on

chassis

Intended Use and Familiarization

Guide

The intended use of this machine is to lift

personnel, including tools, and materials to an

aerial work site. Before operating the machine, it’s

the operator’s responsibility to read and

understand this familiarization guide.

Each person must be trained to operate a

Mobile Elevating Work Platform (MEWP).

Familiarization with the MEWP must be given

to each person who is authorized, competent

and trained.

Only trained and authorized personnel should

be permitted to operate the machine.

The operator is responsible to read,

understand, and obey the manufacturer’s

instructions and safety rules provided in the

Operator’s Manual.

The Operator’s Manual is located in the

manual storage container, at the platform.

For specific product applications, see

Contacting The Manufacturer.

Operator's Manual First Edition • Second Printing

Introduction

2 S®-60 J Part No. 1283765GT

Platform controls symbology and related

machine movement:

Platform level

Platform rotate

Jib boom up/down

Boom up/down

Boom extend/retract

Turntable rotate

Drive forward/reverse

Steer right/left

Ground controls symbology and related

machine movement:

Platform level, jib boom

up/down, boom

extend/retract,and boom

up/down

Turntable rotate and

platform rotate

Sequential functions and movement:

•Drive and steer.

Interlocked functions:

•Elevated drive speed.

•Elevated drive in an off-level condition.

•Drive enable when the boom is rotated past the

non-steer wheels.

•All platform and ground controls.

Limitations of use:

•The intended use of this machine is to lift

personnel, including tools, and materials to an

aerial work site.

•Do not elevate the platform unless the machine

is on firm level ground.

Stability enhancing means:

•Foam filled tires

Restricted operating envelope:

•Not restricted.

First Edition • Second Printing Operator's Manual

Introduction

Part No. 1283765GT S®-60 J 3

Bulletin Distribution and

Compliance

Safety of product users is of paramount

importance to Genie. Various bulletins are used by

Genie to communicate important safety and

product information to dealers and machine

owners.

The information contained in the bulletins is tied to

specific machines using the machine model and

serial number.

Distribution of bulletins is based on the most

current owner on record along with their

associated dealer, so it is important to register

your machine and keep your contact information

up to date.

To ensure safety of personnel and the reliable

continued operation of your machine, be sure to

comply with the action indicated in a respective

bulletin.

To view any open bulletins for your machine, visit

us on the web at www.genielift.com.

Contacting the Manufacturer

At times it may be necessary to contact Genie.

When you do, be ready to supply the model

number and serial number of your machine, along

with your name and contact information. At

minimum, Genie should be contacted for:

Accident reporting

Questions regarding product applications and

safety

Standards and regulatory compliance information

Current owner updates, such as changes in

machine ownership or changes in your contact

information. See Transfer of Ownership, below.

Transfer of Machine Ownership

Taking a few minutes to update owner information

will ensure that you receive important safety,

maintenance and operating information that

applies to your machine.

Please register your machine by visiting us on the

web at www.genielift.com or by calling us toll free

at 1-800-536-1800.

Operator's Manual First Edition • Second Printing

Introduction

4 S®-60 J Part No. 1283765GT

Danger

Failure to obey the instructions and

safety rules in this manual will result

in death or serious injury.

Do Not Operate Unless:

You learn and practice the principles of safe

machine operation contained in this operator’s

manual.

1 Avoid hazardous situations.

Know and understand the safety rules

before going on to the next section.

2 Always perform a pre-operation inspection.

3 Always perform function tests prior to use.

4 Inspect the workplace.

5 Only use the machine as it was intended.

You read, understand and obey the

manufacturer’s instructions and safety rules—

safety and operator’s manuals and machine

decals.

You read, understand and obey employer’s

safety rules and worksite regulations.

You read, understand and obey all applicable

governmental regulations.

You are properly trained to safely operate the

machine.

Safety Sign Maintenance

Replace any missing or damaged safety signs.

Keep operator safety in mind at all times. Use mild

soap and water to clean safety signs. Do not use

solvent-based cleaners because they may

damage the safety sign material.

Hazard Classification

Decals on this machine use symbols, color coding,

and signal words to identify the following:

Safety alert symbol—used to alert

you to potential personal injury

hazards. Obey all safety

messages that follow this symbol

to avoid possible injury or death.

Indicates a hazardous situation

which, if not avoided, will result in

death or serious injury.

Indicates a hazardous situation

which, if not avoided, could result

in death or serious injury.

Indicates a hazardous situation

which, if not avoided, could result

in minor or moderate injury.

Indicates a property damage

message.

First Edition • Second Printing Operator's Manual

Symbol and Hazard Pictorials Definitions

Part No. 1283765GT S®-60 J 5

Symbol andHazard Pictorials Definitions

Fire hazard

Explosion hazard

Do not use ether or

other high energy

starting aids on

machines equipped

with glow plugs.

No smoking.

No flame.

Stop engine.

Fire extinguisher

No smoking

Explosion hazard

Electrocution

hazard

Maintain required

clearance

Tip-over hazard

Tire specifications

Operator's Manual First Edition • Second Printing

Symbol and Hazard Pictorials Definitions

6 S®-60 J Part No. 1283765GT

Wheel load

Wind speed

Maximum capacity

Manual force

Weight of welder

reduces capacity

Tie-down point

Lifting point

Platform tie-down

instructions

Lifting & tie down

instructions

Lanyard anchorage

points

Corrosive acid.

Color coded

direction arrows

Runaway hazard

Collision hazard

Overhead

obstruction

First Edition • Second Printing Operator's Manual

Symbol and Hazard Pictorials Definitions

Part No. 1283765GT S®-60 J 7

Electrocution

hazard

Avoid contact

Disconnect battery

Voltage rating for

power to platform

Pressure rating for

air line to platform

Recovery procedure if tilt alarm sounds

while elevated.

Platform downhill:

1Retract boom.

2Lower boom.

Platform uphill:

1Lower boom.

2Retract boom.

Read the

operator’s manual

Access by trained

and authorized

personnel only

Read the service

manual

Emergency

lowering

Crush hazard

Support the

platform or boom

during

maintenance

Operator's Manual First Edition • Second Printing

General Safety

8 S®-60 J Part No. 1283765GT

GeneralSafety

Andere Handbücher für S-60 J

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Terex Hebesystem Handbücher

Terex

Terex Genie Z-45/25 Bi-Energy Bedienungsanleitung

Terex

Terex MAC 25-4 SL Bedienungsanleitung

Terex

Terex Robot 5000 Service-Handbuch

Terex

Terex Genie GRC-12 Einrichtungshandbuch

Terex

Terex SX135XCH-101 Installations- und Betriebsanleitung

Terex

Terex Genie Superlift Advantage Bedienungsanleitung

Terex

Terex Genie Z-45/25J Bi-Energy Installations- und Betriebsanleitung

Terex

Terex Genie AWP Series Bedienungsanleitung

Terex

Terex Z3413-9461 Installations- und Betriebsanleitung

Terex

Terex Genie Z-34/22 IC Bedienungsanleitung

Terex

Terex Genie Superlift Advantage SL-5 Kurzanleitung

Terex

Terex Genie GR-12 Bedienungsanleitung

Terex

Terex Genie GTH-4014 AU Bedienungsanleitung

Terex

Terex Genie S-80 XC Series Bedienungsanleitung

Terex

Terex Genie Z-51/30J Installations- und Betriebsanleitung

Terex

Terex Genie S-100 Bedienungsanleitung

Terex

Terex Genie Lift Tools Expo Installer Z-45/25 Bedienungsanleitung

Terex

Terex Genie GS-1930/32 Bedienungsanleitung

Terex

Terex Genie Load Lifter Bedienungsanleitung

Terex

Terex Genie Super Series Bedienungsanleitung

Terex

Terex Genie SX-135 XC Bedienungsanleitung

Terex

Terex GTH08E-11500 Installations- und Betriebsanleitung

Terex

Terex Genie SX-105 XC Installations- und Betriebsanleitung

Terex

Terex 43032 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung