Terrier TRT1 Bedienungsanleitung
TRT1 Room Thermostat
TRT1 Room Thermostat
Size Pattern No. Pack 1 Qty Pack 2 Qty Code Barcode Price (£) each ex VAT
General Information
TRT1 Room Thermostat
Code Description A B C
Pegler Yorkshire reserve the right to change specifications
Dimensions
Heating Controls
Pegler Customcare 2 Year Guarantee - Terms & Conditions
Products are subject to a 2 year guarantee that is between Pegler and the final purchaser of the product.
The guarantee is subject to proof of purchase being supplied.
This guarantee does not affect any statutory rights the consumer may have in law.
The guarantee covers manufacturing or material defects and is not applicable where the product is fitted
contrary to conditions of use in our literature.
The guarantee is subject to the following limitations:
1. Damage caused by abusive behaviour and accidental damage to the product are not covered by this
guarantee
The extent of Pegler liability is limited to the cost of the replacement of the defective item and not to fitting or
consequential damages.
Guarantee
Description Minimum Operating
Pressure (bar)
Maximum Cold
Working
Pressure (bar)
Maximum Hot
Working Pressure
(bar)
TRT1 Room
Thermostat No Minimum
Operating Pressure No Maximum Cold
Working Pressure No Maximum Hot
Working Pressure
Pressure and Temperature
Care
Care and Maintenance
No regular care is required for this product.
No regular cleaning is required. Warning: Great care must be taken to avoid using water or water based
cleaning agent. A barely damp cloth should be used. The Thermostat can be easily cleaned with a soft cloth
wiping over the outer cover only. The programmer should be switched off before cleaning.
Maintenance
No maintenance is required for this product.
For any further help please contact your local heating engineer or a qualified electrician.
If your product is under warranty please contact the Service Support Team on: 0800 1560050.
Regulations
The installation and electrical connections must be carried out by a suitably competent person and all work
must be in accordance with the latest edition of BS7671, IEE Wiring Regulations.
The electricity supply to the installation must be isolated before carrying out installation or maintenance.
Terrier heating controls satisfy the requirements of the Electromagnetic Compatibility Directive (89/336/EEC)
and the Low Voltage Directive (73/23/EEC).
Terrier heating controls are manufactured to a strict quality assurance system in accordance with ISO 9000:
2001.
Regulations
Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF
Telephone: Phone +44 (0) 844 243 4400 Fax: +44 (0) 844 243 9870 Website: www.pegleryorkshire.co.uk
Registered office : Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF Company no : 00401507
INSTALLATION & ASSEMBLY:
For correct operation, the thermostat must be positioned approx. 1.5m from
the floor, and always away from draughts and heat sources as shown in
Figure 2. It can be fixed either through a flush mounted connection box, or
directly to the wall, by means of two of the holes on the back part of the
thermostat base.(Important: Locate it on an absolutely flat surface).
1. Remove the thermostat dial by pulling gently outwards.
2. Remove the single screw as shown below and remove the cover (Fig. 3).
3. Fix the thermostat backplate either directly to the wall or to a suitable flush
mounting box with 2 suitable screws (Fig. 4).
4. Connect the electric cables to the terminals in accordance with the wiring
diagram (Fig. 5), also shown inside the thermostat lid.
5. Replace the cover and thermostat dial.
1
38 82
85
2
34
Screw
Screws
Screws
ROOM THERMOSTAT
INSTALLATION INSTRUCTIONS
TRT1
These instructions apply to the following models:
B
4438 Room Thermostat leaflet 22/5/06 9:44 am Page 1
LIMITING THE
TEMPERATURE
RANGE:
1. Set the
thermostat dial
to the desired
temperature.
2. Pull the dial off.
3. Position the stops housed in the
central part of the inside of the dial in
the holes that correspond to the chosen
maximum and minimum temperatures
(Fig 6, above).
4. Replace the dial in its original setting.
WARNING:
Disconnect mains supply before fitting or removing the cover. A switch
having a contact separation of at least 3mm in all poles must be incorporated in
the fixed wiring as a means of fully disconnecting the mains supply.
SETTING:
To set the required temperature, turn the dial until the temperature shown on
the dial aligns with the index mark just below the dial.
TECHNICAL DATA:
Range from 5°C to 30°C
Temperature Differentials 0.4°C with accelerator connected
0.6°C with accelerator disconnected
Range limiting stops
Contact Rating 10(3)A
Voltage Rating 230v, 50Hz
Electrical protection Class II IP30
Contact configuration SPDT
TRT1WL Models - neon indicator lamp, operating on call for heat
Wiring must be in accordance with I.E.E. regulations, and the
control fitted by a competent electrician.
This product complies with the essential requirements of the following EC directives:
EMC 89/336/EEC (as amended by 91/263/EEC and 92/31/EEC)
Low Voltage directive: LVD 73/32/EEC 93/68/EEC
Pegler Limited, St. Catherine’s Avenue, Doncaster, South Yorkshire, DN4 8DF
Technical Helpline: 0870 1200285
56
IC: 04500352
TRT1 WL Models
only
4438 Room Thermostat leaflet 22/5/06 9:44 am Page 2
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Terrier Thermostat Handbücher
Beliebte Thermostat Handbücher anderer Marken
EWELLY
EWELLY EW-181 Bedienungsanleitung
Prolon
Prolon T1100 Montageanleitung
Computherm
Computherm Q20 Bedienungsanleitung
Heatmiser
Heatmiser neoStat Bedienungsanleitung
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung
