TESTO BN3464JH Bedienungsanleitung

Dieses Handbuch passt für folgende Modelle

2

Inhaltsverzeichnis

Andere TESTO Nagelpistole Handbücher

TESTO

TESTO BN2190F1 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung

Black & Decker

Black & Decker 90514937 Bedienungsanleitung

Instruction Manual

34° Metal Connector

WARNING

BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL, TO UNDERSTAND

AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. IF YOU HAVE ANY QUESTIONS,

CONTACT WITH OUR REPRESENTATIVES OR DISTRIBUTOR.

BN3464JH No.01530000290

BN3438JH No.01630000290

BN3460JH No.02810000290

2

CONTENTS

PAGE

TOOL SPECIFICATIONS

NAIL SPECIFICATIONS

EXTERNAL TOOL PARTS

SAFETY INSTRUCTIONS

LUBRICATION AND MAINTENANCE

ACTUATING TOOL

OPERATING THE TOOL

TROUBLESHOOTING GUIDE

3-4

3-4

3-4

5-7

8

8

9-10

11

TOOL SPECIFICATIONS

NAIL SPECIFICATIONS

EXTERNAL TOOL PARTS

3

Height ............................................................................................. : 11.4" (290mm)

Width .............................................................................................. : 3.5" (89mm)

Length ............................................................................................ : 11.8" (299mm)

Weight ............................................................................................ : 4.6 lbs. (2.1 kgs)

Recommended Operating Pressure ............................................. : 70-120 psi (4.9-8.3 bar)

Air Consumption ........................................................................... :

Loading Capacity .......................................................................... : up to 32 nails

NOISE CHARACTERISTIC VALUES IN ACCORDANCE WITH ISO 3774, ISO 11201:

A-weighted single-event sound pressure level at operator's position.. : LpA,1s =

A-weighted single-event sound power level ..................................... : LwA,1s =

A-weighted single-event surface sound pressure level .................... : LpA,1s =

VIBRATION CHARACTERISTIC VALUES IN ACCORDANCE WITH ISO 8862-1:

Weighted root mean square acceleration .......................................... = 3.6 m/s2

Paper collated full round head metal connector nails

Nail Lengths .................................................................................. : 1 1/2"(38mm)

Shank Diameter ............................................................................ : .131"&.148" (3.3 & 3.8mm)

Nail Stick Angle ............................................................................ : 34°

360°

EXHAUST

TRIGGER

MAGAZINE

RETAINER

SAFETY NOSE

ASSEMBLY

PUSHER

MAGAZINE

88 dBA

101 dBA

88 dBA

4

HJ0643NBHJ4643NB.oNledoM

Length )mm703(”1.21)mm703(”1.21

Width )mm901(”3.4)mm901(”3.4

Height )mm953(”1.41)mm953(”1.41

Weight )sgk5.2(sbl5.5)sgk5.2(sbl5.5

Operating Pressure 70 ~ 120 psi

(4.9 ~ 8.3 bar)

70 ~ 120 psi

(4.9 ~ 8.3 bar)

Loading Capacity slian03slian03

Accessories kooHtleBkooHtleB

A

-weighted single-event

sound pressure level

--- LpA, 1s, d

ABd29ABd29

A

-weighted single-event

sound power level

--- LWA, 1s, d

ABd101ABd101

Weighted root mean

square acceleration

--- m/s22.7m/s2s/m7.2 2

Model No. P3833NCC3833NCP0933NCC0933NC

Nail Length 2”-3 1/2”

(50-90mm) 2”-3 1/2” (50-90mm) 2”-3 1/4” (50-83mm) 2”-3 1/4”

(50-83mm)

Shank Diameter .099”-.131”

(2.5-3.3mm)

.099”-.131”

(2.5-3.3mm) .099”-.131” (2.5-3.3mm) .099”-.131”

(2.5-3.3mm)

Shank Type Smooth,

Ring, Screw Smooth, Ring, Screw Smooth, Ring, Screw Smooth, Ring,

Screw

Model No. HJ0643NBHJ4643NB

Nail Angle 34°43 °

Shank Diameter Ø.131” & .148”

(3.3 & 3.8mm)

Ø.162”

(4.0mm)

Nail Length 1 1/2” & 2 1/2”

(38 & 64mm)

1 5/8” & 2” & 2 1/4”

(40 & 50 & 60mm)

BELT

HOOK

SAFETY NOSE

ASSEMBLY

360° EXHAUST

TRIGGER

MAGAZINE

RETAINER

MAGAZINE

PUSHER

TOOL SPECIFICATIONS

NAIL SPECIFICATIONS

EXTERNAL TOOL PARTS

5

SAFETY INSTRUCTIONS

WARNING: Read this manual and understand all instructions before operating the tool.

If you have any questions, please contact with our authorized representatives.

OX

CO2

The operator and all persons in the general area should wear

safety glasses to guard against flying fasteners and debris,

which could cause severe eye injury. Safety glasses are per

requirements of the Regulatory Authority. Always wear hearing

protection and hard hat.

Never use oxygen, carbon dioxide or any other bottled gas as

a power source for this tool Danger of explosion and/or serious

personal injury may result.

Use only clean, dry regulated compressed air at recommended

pressure

Tools shall not be connected to a compressor which potentially

exceeds 175 psi or 12 bar.

Air hose rated for a maximum operating pressure of 150 psi

(10.3 bar) or 150% of the maximum system pressure, whichever,

is higher.

Disconnect tool from air supply and remove fasteners from

magazine before doing tool maintenance, clearing a jammed

fastener, leaving work area, moving tool to another location, or

handing the tool to another person.

120 Psi

8.3 bar

70 Psi

4.9 bar

6

Coupling must be used which removed all pressure from the tool

when the coupling joint is disconnected.

Never use tool that is leaking air, has damaged or missing parts.

Never point the tools at co-workers or yourself at any time .

Never carry the tool from place to place holding the trigger.

Do not alter or modify this tool from the original design or

function without approval from us or authorized representatives.

Do not remove spring from contact trip, inadvertent actuation

could occur.

Always maintain proper footing and place yourself in a firmly

balance position when using or handling the tool.

Do not drive fasteners on top of other fasteners, the fasteners

can ricochet and hurt someone.

7

Never use the body of the tool or top cap as a hammer, always

use the tool for its intended use. Do not discharge fasteners into

concrete, stone, or any material too hard for the fastener to

penetrate.

Do not drive fasteners close to the edge of the work surface.

The workpiece may split causing the fastener to ricochet, fly free

or hit someone.

Keep hands and body away from the discharge area of the tool.

Keep face and body away from back of the tool cap when

working in restricted areas. Sudden recoil can result in hard

impact to the body.

Never use tool in the presence of flammable dust, gases or

fumes. The tool may produce a spark that could ignite gases

causing a fire and cause the tool to explode.

Be aware of material thickness when using the nailer.

8

LUBRICATION AND MAINTENANCE

Use Pneumatic tool oil or a non-detergent oil. Do not use

detergent oil or additives as they will damage o-rings and rubber

parts.

Use a filter and regulator when possible

Add pneumatic oil into the air inlet twice daily. (Depending on

frequency of tool use)

Wipe tool clean daily and inspect for wear. Use solvents only if

necessary - Do Not Soak. (Solvents may damage o-rings and

other tool parts)

Drain compressor tanks and hoses daily

Clean magazine, pusher, and contact trip mechanism

periodically.

All screws, nuts and fasteners should be kept tight and

undamaged. Loose screws result in unsafe operation and parts

breakage.

ACTUATING TOOL

WARNING: Always wear eye and hearing protection when operating tool. The tool can be

actuated using Sequential Fire mode.

SEQUENTIAL FIRE ACTION:

1. The operator must first place the tip of the nail into the metal connectors preformed

hole. Then hold the safety nose FULLY against the work surface.

2. Pull the trigger firing a fastener into the material.

3. The tool will not fire again until the trigger is released and the safety is removed

completely from the material being used.

4. To fire the next fastener, repeat the above steps.

9

OPERATING THE TOOL

when changing one driving location to another involves the use

of scaffoldings, stairs, ladders, or ladder alike constructions,

e.g. roof laths.

closing boxes or crates.

fitting transportation safety systems e.g. on vehicles and

wagons.

" Do not use on scaffoldings, ladders" ,

and shall not be used for specific application:

Read Safety Instruction section of this manual.

Loading the tool:

WARNING: Always connect air before loading the tool.

Loading the nails:

1. Insert strip of nails from the rear of magazine and

slide nails all the way to the front of magazine.

2. Pull pusher toward the rear of magazine beyond

the last nail, then release to engage pusher to

strip of nails.

3. Push nail stopper (A) downward to prevent strip

of nails from being backward while nailing.

Removing the nails:

1. Push nail stopper (A) upward to release the nails.

2. Depress the pusher tab to disengage the pusher

from the nails. Slide the pusher forward past the

nails to the nose.

3. Depress the magazine retainer (B) and slide nails

past the magazine retainer and out the magazine.

A

B

10

CAUTION: Do not store the tool in a cold weather environment to prevent frost or ice formation

the tools operating valves and mechanisms that could cause tool failure.

PLACEMENT OF NAIL:

Metal connector nails are not designed to penetrate metal. When installing metal connectors,

always place the exposed point of the metal connector nail into the metal connector’s

pre-formed hole, and orient so the nail is perpendicular to the hole before attempting to drive

a fastener.

Operation in Hot Weather

Keep tool out of direct sunlight as excessive heat can deteriorate bumpers, o-rings and other

rubber parts resulting in increased maintenance.

Operation in Cold Weather

When operating tools at temperatures near and below freezing, the moisture in the air line

may freeze and prevent tool operation.

1. Reduce the air pressure to 80 psi (5.5 bar) or less.

2. Removed all fasteners from magazine.

3. Connect air and free-fire (blank-fire) the tool. Slow

speed operation tends to warm up the moving part.

Correct placement of nail Incorrect placement of nail