Texas Instruments MSP430FR6989 LaunchPad Bedienungsanleitung

User's Guide

SLAU627A–May 2015–Revised July 2015

MSP430FR6989 LaunchPad™ Development Kit

(MSP

‑‑

EXP430FR6989)

The MSP-EXP430FR6989 LaunchPad™ Development Kit is an easy-to-use evaluation module (EVM) for

the MSP40FR6989 microcontroller (MCU). It contains everything needed to start developing on the ultra-

low-power MSP430FRx FRAM microcontroller platform, including on-board emulation for programming,

debugging, and energy measurements.

Figure 1. MSP-EXP430FR6989 LaunchPad Development Kit

LaunchPad, BoosterPack, EnergyTrace++, EnergyTrace, E2E are trademarks of Texas Instruments.

All other trademarks are the property of their respective owners.

SLAU627A–May 2015–Revised July 2015 MSP430FR6989 LaunchPad™ Development Kit (MSP

‑

EXP430FR6989)

www.ti.com

Contents

1 Getting Started............................................................................................................... 3

2 Hardware...................................................................................................................... 5

3 Software Examples ........................................................................................................ 18

4 Resources................................................................................................................... 20

5 FAQs......................................................................................................................... 28

6 Schematics.................................................................................................................. 29

List of Figures

1 MSP-EXP430FR6989 LaunchPad Development Kit.................................................................... 1

2 MSP-EXP430FR6989 Overview........................................................................................... 5

3 MSP-EXP430FR6989 Block Diagram..................................................................................... 6

4 MSP430FR6989IPZ Pinout................................................................................................. 7

5 eZ-FET Emulator............................................................................................................. 8

6 eZ-FET Isolation Jumper Block Diagram................................................................................ 10

7 Application Backchannel UART in Device Manager................................................................... 11

8 LCD Segment Layout...................................................................................................... 11

9 MSP-EXP430FR6989 Power Block Diagram........................................................................... 14

10 LaunchPad to BoosterPack Connector Pinout ......................................................................... 17

11 TI Resource Explorer Cloud .............................................................................................. 21

12 CCS Cloud .................................................................................................................. 22

13 Directing the Project>Import Function to the Demo Project .......................................................... 23

14 When CCS Has Found the Project ...................................................................................... 24

15 Using TI Resource Explorer to Browse MSP-EXP430FR6989 in MSPWare....................................... 26

16 Schematics (1 of 6) ........................................................................................................ 29

17 Schematics (2 of 6) ........................................................................................................ 30

18 Schematics (3 of 6) ........................................................................................................ 31

19 Schematics (4 of 6) ........................................................................................................ 32

20 Schematics (5 of 6) ........................................................................................................ 33

21 Schematics (6 of 6) ........................................................................................................ 34

List of Tables

1 EnergyTrace Technology................................................................................................... 8

2 Isolation Block Connections................................................................................................ 9

3 LCD FH-1138P Segment Mapping....................................................................................... 12

4 LCD-to-MSP Connections................................................................................................. 13

5 Hardware Change Log..................................................................................................... 18

6 Software Examples ........................................................................................................ 18

7 IDE Minimum Requirements for MSP-EXP430FR6989............................................................... 18

8 Source File and Folders................................................................................................... 19

9 Source File and Folders................................................................................................... 20

10 How MSP Device Documentation is Organized........................................................................ 27

2MSP430FR6989 LaunchPad™ Development Kit (MSP

‑

EXP430FR6989) SLAU627A–May 2015–Revised July 2015

Submit Documentation Feedback

www.ti.com

Getting Started

1 Getting Started

1.1 Introduction

The MSP-EXP430FR6989 LaunchPad Development Kit is an easy-to-use Evaluation Module (EVM) for

the MSP40FR6989 microcontroller (MCU). It contains everything needed to start developing on the ultra-

low-power MSP430FRx FRAM microcontroller platform, including on-board emulation for programming,

debugging and energy measurements. The board features on-board buttons and LEDs for quick

integration of a simple user interface as well as a Liquid Crystal Display (LCD) display which showcases

the integrated driver that can drive up to 320 segments. It also offers direct access to the Extended Scan

Interface, which is a dual analog front-end (AFE) created for low-power rotation detection. The

MSP430FR6989 device features ultra-low power consumption, 128KB of embedded ferroelectric random

access memory (FRAM), a nonvolatile memory known for its ultra-low power, high endurance, and high-

speed write access.

Rapid prototyping is simplified by the 40-pin BoosterPack™ Plug-in Module headers, which support a wide

range of available BoosterPack modules. You can quickly add features like wireless connectivity, graphical

displays, environmental sensing, and much more. Design your own BoosterPack or choose among many

already available from TI and third party developers.

The out-of-box provided with the MSP-EXP430FR6989 LaunchPad features the on-board segmented

display and offers two operating modes. Stopwatch Mode can run a timer for up to 24 hours, or

alternatively operate split time, where the display can be frozen and the stopwatch continues running in

the background. The second mode provides a simple thermometer application using the on-chip

temperature sensor. The temperature is displayed on the LCD and can be shown in degrees Fahrenheit or

Celsius.

Free software development tools are also available, such as TI's Eclipse-based Code Composer Studio

(CCS) and IAR Embedded Workbench. Both of these IDEs support EnergyTrace++™ technology for real-

time power profiling and debugging when paired with the MSP430FR6989 LaunchPad. More information

about the LaunchPad, the supported BoosterPack modules and available resources can be found at TI's

LaunchPad portal.

1.2 Key Features

• MSP ULP FRAM technology based MSP430FR6989 16-bit MCU

• EnergyTrace++ technology available for ultra-low-power debugging

• 40 pin LaunchPad standard leveraging the BoosterPack ecosystem

• Onboard eZ-FET emulation

• Two buttons and two LEDs for user interaction

• Segmented LCD

• Pins for direct access to the Extended Scan Interface

1.3 What's Included

1.3.1 Kit Contents

• 1x MSP-EXP430FR6989 LaunchPad Development Kit

• 1x Micro USB cable

• 1x Quick Start Guide

1.3.2 Software Examples

• Out-of-Box Software

• Blink LED

SLAU627A–May 2015–Revised July 2015 MSP430FR6989 LaunchPad™ Development Kit (MSP

‑

EXP430FR6989)

Getting Started

www.ti.com

1.4 First Steps: Out-of-Box Experience

An easy way to get familiar with the EVM is by using its preprogrammed out-of-box code. This code

demonstrates some key features from a user level.

1.4.1 Connecting to the Computer

Connect the LaunchPad using the included USB cable to a computer. A green power LED should

illuminate. For proper operation, drivers are needed. TI recommends installing these driver by installing an

IDE such as TI's CCS or IAR EW430. Drivers are also available at http://www.ti.com/MSPdrivers.

1.4.2 Running the Out-of-Box Demo

When connected to your computer, the LaunchPad powers up and displays a greeting message on the

LCD. Press and hold the S1 and S2 buttons simultaneously to select a new mode. See Section 3 for

detailed explanations of each mode.

1.4.2.1 Stopwatch Mode

This mode provides a simple stopwatch application. It supports split time, where the display freezes while

the stopwatch continues running in the background.

Timer Stopped:

S1 : Start time

S2 : Reset time

Timer Running:

S1 : Stop time

S2 : Split time (lap time)

1.4.2.2 Temperature Mode

This mode provides a simple thermometer application. Using the on-chip temperature sensor, the

temperature is displayed on the LCD.

S1 : Pause current temperature

S2 : Toggle temperature between °F and °C

1.5 Next Steps: Looking Into the Provided Code

After the EVM features have been explored, the fun can begin. It's time to open an integrated

development environment and start editing the code examples. Refer to Section 4 for available IDEs and

where to download them.

The quickest way to get started using the LaunchPad is to use TI's Cloud Development Tools,

http://dev.ti.com. The cloud-based Resource Explorer provides access to all of the examples and

resources in MSPWare. Code Composer Studio Cloud is a simple Cloud-based IDE that enables

developing and running applications on the LaunchPad.

The out-of-box source code and more code examples are provided for download at

http://www.ti.com/tool/msp-exp430fr6989. Code is licensed under BSD, and TI encourages reuse and

modifications to fit specific needs.

Section 3 describes all functions in detail and provides a project structure to help familiarize you with the

code.

With the onboard eZ-FET emulator debugging and downloading new code is simple. A USB connection

between the EVM and a PC through the provided USB cable is all that is needed.

4MSP430FR6989 LaunchPad™ Development Kit (MSP

‑

EXP430FR6989) SLAU627A–May 2015–Revised July 2015

Submit Documentation Feedback

www.ti.com

Hardware

2 Hardware

Figure 2 shows an overview of the MSP-EXP430FR6989 hardware.

Figure 2. MSP-EXP430FR6989 Overview

SLAU627A–May 2015–Revised July 2015 MSP430FR6989 LaunchPad™ Development Kit (MSP

‑

EXP430FR6989)

Target Device

MSP430FR6989

Crystal

32.768 kHz

Micro‐B

USB

3.3‐V

LDO

ESD

Protection

Debug

MCU

LED

Red or Green

Crystal

4 MHz

UART or SBW to

Target

User Interface

Two Buttons and

Two LEDs

40‐pin LaunchPad

Standard Headers

Power to Target

Reset

Button Segmented LCD

EnergyTrace

Interface to ESI

Hardware

www.ti.com

2.1 Block Diagram

Figure 3 shows the block diagram.

Figure 3. MSP-EXP430FR6989 Block Diagram

2.2 Hardware Features

2.2.1 MSP430FR6989

The MSP430FR6989 is the next device in TI's new ULP FRAM technology platform. FRAM is a cutting

edge memory technology, combining the best features of flash and RAM into one nonvolatile memory.

Device features include:

• 1.8-V to 3.6-V operation

• 16-bit RISC architecture up to 16-MHz system clock and 8-MHz FRAM access

• 128KB of nonvolatile FRAM

• 100 µA/MHz active mode and 350 nA standby with RTC and 3.7-pF crystal

• Certified ULPBench score of 109

• 320-segment LCD controller

• Extended Scan Interface

• 16-channel 12-bit ADC

• Comparator

• Five Timers

• Direct memory access

• 256-bit AES

• 83 GPIOs

6MSP430FR6989 LaunchPad™ Development Kit (MSP

‑

EXP430FR6989) SLAU627A–May 2015–Revised July 2015

Submit Documentation Feedback

P4.3/UCA0SOMI/UCA0RXD/UCB1STE

2P1.4/UCB0CLK/UCA0STE/TA1.0/S1

3P1.5/UCB0STE/UCA0CLK/TA0.0/S0

4P1.6/UCB0SIMO/UCB0SDA/TA0.1

5P1.7/UCB0SOMI/UCB0SCL/TA0.2

6R33/LCDCAP

7P6.0/R23

8P6.1/R13/LCDREF

9P6.2/COUT/R03

10P6.3/COM0

11P6.4/TB0.0/COM1

12P6.5/TB0.1/COM2

13P6.6/TB0.2/COM3

14P2.4/TB0.3/COM4/S43

15P2.5/TB0.4/COM5/S42

16P2.6/TB0.5/ESIC1OUT/COM6/S41

17P2.7/TB0.6/ COM7/S40ESIC2OUT/

18P10.2/TA1.0/SMCLK/S39

19P5.0/TA1.1/MCLK/S38

20P5.1/TA1.2/S37

21P5.2/TA1.0/TA1CLK/ACLK/S36

22P5.3/UCB1STE/S35

23P3.0/UCB1CLK/S34

24P3.1/UCB1SIMO/UCB1SDA/S33

25P3.2/UCB1SOMI/UCB1SCL/S32

DVSS1

DVCC1

TEST/SBWTCK

RST/NMI/SBWTDIO

PJ.0/TDO/TB0OUTH/SMCLK/SRSCG1

PJ.1/TDI/TCLK/MCLK/SRSCG0

PJ.2/TMS/ACLK/SROSCOFF

PJ.3/TCK/COUT/SRCPUOFF

P6.7/TA0CLK/S31

P7.5/TA0.2/S30

P7.6/TA0.1/S29

P10.1/TA0.0/S28

P7.7/TA1.2/TB0OUTH/S27

P3.3/TA1.1/TB0CLK/S26

P3.4/UCA1SIMO/UCA1TXD/TB0.0/S25

P3.5/UCA1SOMI/UCA1RXD/TB0.1/S24

P3.6/UCA1CLK/TB0.2/S23

P3.7/UCA1STE/TB0.3/S22

P8.0/RTCCLK/S21

P8.1/DMAE0/S20

P8.2/S19

P8.3/MCLK/S18

P2.3/UCA0STE/TB0OUTH

P2.2/UCA0CLK/TB0.4/RTCCLK

P2.1/UCA0SOMI/UCA0RXD/TB0.5/DMAE0

51 P2.0/UCA0SIMO/UCA0TXD/TB0.6/TB0CLK

52 P7.0/TA0CLK/S17

53 P7.1/TA0.0/S16

54 P7.2/TA0.1/S15

55 P7.3/TA0.2/S14

56 P7.4/SMCLK/S13

57 DVSS2

58 DVCC2

59 P8.4/A7/C7

60 P8.5/A6/C6

61 P8.6/A5/C5

62 P8.7/A4/C4

63 P1.3/TA1.2 /A3/C3/ESITEST4

64 P1.2/TA1.1/TA0CLK/COUT/A2/C2

65 P1.1/TA0.2/TA1CLK/COUT/A1/C1/VREF+/VeREF+

66 P1.0/TA0.1/DMAE0/RTCCLK/A0/C0/VREF-/VeREF-

67 P9.0/ESICH0/ESITEST0/A8/C8

68 P9.1/ESICH1/ESITEST1/A9/C9

69 P9.2/ESICH2/ESITEST2/A10/C10

70 P9.3/ESICH3/ESITEST3/A11/C11

71 P9.4/ESICI0/A12/C12

72 P9.5/ESICI1/A13/C13

73 P9.6/ESICI2/A14/C14

74 P9.7/ESICI3/A15/C15

75 ESIDVCC

ESIDVSS

ESICI

ESICOM

AVCC1

AVSS3

PJ.7/HFXOUT

PJ.6/HFXIN

AVSS1

PJ.4/LFXIN

PJ.5/LFXOUT

AVSS2

P5.4/UCA1SIMO/UCA1TXD/S12

P5.5/UCA1SOMI/UCA1RXD/S11

P5.6/UCA1CLK/S10

P5.7/UCA1STE/TB0CLK/S9

P4.4/UCB1STE/TA1CLK/S8

P4.5/UCB1CLK/TA1.0/S7

P4.6/UCB1SIMO/UCB1SDA/TA1.1/S6

P4.7/UCB1SOMI/UCB1SCL/TA1.2/S5

P10.0/SMCLK/S4

P4.0/UCB1SIMO/UCB1SDA/MCLK/S3

P4.1/UCB1SOMI/UCB1SCL/ACLK/S2

DVSS3

DVCC3

100

P4.2/UCA0SIMO/UCA0TXD/UCB1CLK

www.ti.com

Hardware

On devices with UART BSL: P2.0: BSLTX; P2.1: BSLRX

On devices with I2C BSL: P1.6: BSLSDA; P1.7: BSLSCL

Figure 4. MSP430FR6989IPZ Pinout

SLAU627A–May 2015–Revised July 2015 MSP430FR6989 LaunchPad™ Development Kit (MSP

‑

EXP430FR6989)

Hardware

www.ti.com

2.2.2 eZ-FET Onboard Emulator With EnergyTrace™ Technology

To keep development easy and cost effective, TI's LaunchPad Development Kits integrate an onboard

emulator, which eliminates the need for expensive programmers. The MSP-EXP430FR6989 has the eZ-

FET emulator (see Figure 5), which is a simple and low-cost debugger that supports all MSP430 device

derivatives.

Figure 5. eZ-FET Emulator

The MSP-EXP430FR6989 LaunchPad features full EnergyTrace++ technology. The EnergyTrace

functionality varies across the MSP portfolio, shown in Table 1.

Table 1. EnergyTrace Technology

Features EnergyTrace™ Technology EnergyTrace++™ Technology

Current Monitoring Yes Yes

CPU State No Yes

Peripheral and System State No Yes

Devices Supported All MSP430 MCUs MSP430FR59xx and FR69xx MCUs

Development Tool Required MSP-FET or eZ-FET MSP-FET or eZ-FET

The eZ-FET also provides a "backchannel" UART-over-USB connection with the host, which can be very

useful during debugging and for easy communication with a PC. The provided UART supports hardware

flow control (RTS and CTS), although by default these signals are not connected to the target.

In Figure 5, the dotted line through J101 divides the eZ-FET emulator from the target area. The signals

that cross this line can be disconnected by jumpers on J101, the isolation jumper block. More details on

the isolation jumper block are in Section 2.2.3.

The eZ-FET hardware can be found in the schematics in Section 6 and in the MSP-EXP430FR6989

Hardware Design Files. The software and more information about the debugger can be found on the eZ-

FET wiki.

8MSP430FR6989 LaunchPad™ Development Kit (MSP

‑

EXP430FR6989) SLAU627A–May 2015–Revised July 2015

Submit Documentation Feedback

www.ti.com

Hardware

2.2.3 Emulator Connection: Isolation Jumper Block

The isolation jumper block at jumper J101 connects or disconnects signals that cross from the eZ-FET

domain into the MSP430FR6989 target domain. This includes eZ-FET Spy-Bi-Wire signals, application

UART signals, and 3.3-V and 5-V power (see Table 2 and Figure 6).

Reasons to open these connections:

• To remove any and all influence from the eZ-FET emulator for high accuracy target power

measurements

• To control 3-V and 5-V power flow between the eZ-FET and target domains

• To expose the target MCU pins for other use than onboard debugging and application UART

communication

• To expose the programming and UART interface of the eZ-FET so that it can be used for devices other

than the onboard MCU.

Table 2. Isolation Block Connections

Jumper Description

GND Ground

5V 5-V VBUS from USB

3V3 3.3-V rail, derived from VBUS in the eZ-FET domain

Backchannel UART: Ready-To-Send, for hardware flow control. The target can use this to indicate whether it is

RTS >> ready to receive data from the host PC. The arrows indicate the direction of the signal.

Backchannel UART: Clear-To-Send, for hardware flow control. The host PC (through the emulator) uses this to

CTS << indicate whether it is ready to receive data. The arrows indicate the direction of the signal.

Backchannel UART: The target FR6989 receives data through this signal. The arrows indicate the direction of the

RXD << signal.

Backchannel UART: The target FR6989 sends data through this signal. The arrows indicate the direction of the

TXD >> signal.

SBW RST Spy-Bi-Wire emulation: SBWTDIO data signal. This pin also functions as the RST signal (active low).

SBW TST Spy-Bi-Wire emulation: SBWTCK clock signal. This pin also functions as the TST signal.

SLAU627A–May 2015–Revised July 2015 MSP430FR6989 LaunchPad™ Development Kit (MSP

‑

EXP430FR6989)

eZ-FET

Emulator

MCU

Isolation

Jumper Block

Spy-Bi-Wire (SBW)

Emulation

Application UART

3.3V Power

5V Power

Target MSP430

MCU

eZ-FETMSP430 Target

USB Connector

in out

LDO

BoosterPack Header

USB

EnergyTrace

Hardware

www.ti.com

Figure 6. eZ-FET Isolation Jumper Block Diagram

2.2.4 Application (or "Backchannel") UART

The backchannel UART allows communication with the USB host that is not part of the target application's

main functionality. This is very useful during development, and also provides a communication channel to

the PC host side. This can be used to create graphical user interfaces (GUIs) and other programs on the

PC that communicate with the LaunchPad.

Figure 7 shows the pathway of the backchannel UART. The backchannel UART is the UART on

eUSCI_A1. This UART channel is separate from the UART on the 20-pin BoosterPack connector

(eUSCI_A0).

On the host side, a virtual COM port for the application backchannel UART is generated when the

LaunchPad enumerates on the host. You can use any PC application that interfaces with COM ports,

including terminal applications like Hyperterminal or Docklight, to open this port and communicate with the

target application. You need to identify the COM port for the backchannel. On Windows PCs, Device

Manager can assist.

10 MSP430FR6989 LaunchPad™ Development Kit (MSP

‑

EXP430FR6989) SLAU627A–May 2015–Revised July 2015

Submit Documentation Feedback

Inhaltsverzeichnis

Andere Texas Instruments Mikrocontroller Handbücher

Texas Instruments

Texas Instruments MSP430F6775 Bedienungsanleitung

Texas Instruments

Texas Instruments TLC2543 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F67481 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP-EXP430G2ET Bedienungsanleitung

Texas Instruments

Texas Instruments SimpleLink CC2650 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP432P401R Bedienungsanleitung

Texas Instruments

Texas Instruments TMS370 Series Benutzerhandbuch

Texas Instruments

Texas Instruments MSP430FG6626 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP-FET430 Bedienungsanleitung

Texas Instruments

Texas Instruments Concerto F28M35 Series Produkthandbuch

Texas Instruments

Texas Instruments MSP430F6725A Bedienungsanleitung

Texas Instruments

Texas Instruments DA8xx EVM PSP Bedienungsanleitung

Texas Instruments

Texas Instruments CC1200 Bedienungsanleitung

Texas Instruments

Texas Instruments CC2540 Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon Products CC2400DK Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon Products CC1050DK Bedienungsanleitung

Texas Instruments

Texas Instruments CC3235MODSF SimpleLink Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F563x Bedienungsanleitung

Texas Instruments

Texas Instruments TAS5132DDV6EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320DM357 Bedienungsanleitung

Texas Instruments

Texas Instruments Arrow IoT Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F6724 Bedienungsanleitung

Texas Instruments

Texas Instruments 430BOOST-SENSE1 Bedienungsanleitung

Texas Instruments

Texas Instruments AM5728 Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F800 Bedienungsanleitung

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Bedienungsanleitung

Mikroe

Mikroe click Proximity 2 Bedienungsanleitung