Texas Instruments MSP432P401R Bedienungsanleitung

MSP432P401R Launchpad External Target Mod

This guide walks through the steps of connecting to and programming an external target using

the MSP432P401R LaunchPad Development Kit.

Figure 1: MSP432P401R LaunchPad Development Kit

Step 1:

Remove the board from the packaging.

Figure 2: MSP432P401R LaunchPad out of box (with wires attached)

Step 2:

Remove the jumpers from the isolation header as well as switch S101 to the “XDS-ET”position (not the

“Ext Debug”position).

Figure 3: Headers Removed and Switch Positioned

Step 3:

Attach wires to each of the positions in J103 on the side of the board near the reset button.

Figure 4: Jumper wires soldered into J103 on the LaunchPad

Step 4:

Attach a wire for the “TDI”signal by soldering a wire into pin 6 of the debug select switch (S101) as

shown in the figure below. Ensure that the switch remains in the “XDS-ET”position.

Figure 5: Wire Soldered to "TDI" Signal on S101

Step 5:

Attach a wire for the “SWO”signal by soldering a wire to pin 12 of IC111. Since the traces are small on

that component, it is easiest to attach the wire directly to the trace.

Figure 6: Wire Soldered to "SWO" Signal from Pin 12 on IC111

Carefully scratch off the soldermask from the trace leading to pin 12 on IC111. This will allow for more

space to solder a wire.

Figure 7: Close-up of IC111 and the Soldering Location for the "SWO" Signal

Solder a wire to the exposed copper of the trace and be careful to not strain the wire as it may damage

the board.

Figure 8: Wire Soldered to the "SWO" Signal

Step 6:

Attach the wires from J103 on the LaunchPad to their corresponding positions on whatever target board

you want to program. Not all signals are required from J103.

Step 7:

Attach the “TDI”and “SWO”wires to their corresponding positions on the target board.

Step 8:

Connect the MSP432P401R LaunchPad to the computer via the micro USB cable and check to see if

“LED102”is illuminated green near the reset button. If the LED is not on, try cycling the power on the

target board by quickly removing and replacing the +3.3V wire. Repeat with pauses in between until

LED02 illuminates.

Figure 9: Launch Pad Connected to Target with LED02 Illuminated

Step 9:

Program the external target board using your preferred method. Note that I have only tried this with

Code Composer Studio and Energia and it works fine but I’m assuming it should work with other IDEs.

No guarantees though.

Andere Handbücher für MSP432P401R

Inhaltsverzeichnis

Andere Texas Instruments Mikrocontroller Handbücher

Texas Instruments

Texas Instruments TMS320F28376D Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon Products CC2400DK Programmierhandbuch

Texas Instruments

Texas Instruments bq24707EVM Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Texas Instruments

Texas Instruments BQ769142 Bedienungsanleitung

Texas Instruments

Texas Instruments C2000 Piccolo LaunchPad Installationsanleitung

Texas Instruments

Texas Instruments EK-TM4C123GXL-BOOSTXL-SENSHUB Bedienungsanleitung

Texas Instruments

Texas Instruments Delfino TMS320F28377D controlCARD Technisches Handbuch

Texas Instruments

Texas Instruments CC2540 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F6720A Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F643 Series Bedienungsanleitung

Texas Instruments

Texas Instruments CDT370 Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

Texas Instruments

Texas Instruments Errata MSP430F6779 Bedienungsanleitung

Texas Instruments

Texas Instruments CC1110-CC1111DK Bedienungsanleitung

Texas Instruments

Texas Instruments CC2430ZDK Bedienungsanleitung

Texas Instruments

Texas Instruments TMUX646EVM Bedienungsanleitung

Texas Instruments

Texas Instruments MSPM0G310 Series Bedienungsanleitung

Texas Instruments

Texas Instruments DA8xx EVM PSP Bedienungsanleitung

Texas Instruments

Texas Instruments TMDXRM42HDK Bedienungsanleitung

Texas Instruments

Texas Instruments TMS570LC43x Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430G2744DA Bedienungsanleitung

Texas Instruments

Texas Instruments CC110 Series Leitfaden

Texas Instruments

Texas Instruments CC2531 Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F800 Bedienungsanleitung

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Bedienungsanleitung

Mikroe

Mikroe click Proximity 2 Bedienungsanleitung