Texas Instruments AMC1210EVM Bedienungsanleitung

1 EVM Overview

1.1 Analog Interface

User's GuideSLAU185 – August 2006

AMC1210EVM

Contents1 EVM Overview ...................................................................................... 12 EVM Operation ...................................................................................... 33 AMC1210 Modular EVM Bill of Materials ........................................................ 4

The AMC1210 modular evaluation module (EVM) provides four modulator channels from the ADS1204 forthe AMC1210. Two are designated for resolver applications and two are designated for currentmeasurements. All interface modes of the AMC1210 are provided.

The new modular EVM form factor allows for direct evaluation of the AMC1210’s performance andoperating characteristics. This EVM is compatible with the HPA-MCU Interface Board (SLAU106 ) fromTexas Instruments.

•Four modulator channels provided by ADS1204•All AMC1210 interface modes available•Direct operation with a variety of DSK and microcontroller platforms from Texas Instruments•All four ADS1204 channels have an input range of 0 V to 5 V.

The AMC1210 modular EVM is designed for easy interfacing to resolvers and current sensors. ConnectorJ05 is a 9-pole DSUB jack for easy connection to standard resolvers. To hold the floating resolver inputsto a predefined common mode level, a 2.5-V voltage is added on the resolver inputs.Signal Description

J05.1 IN1+ Positive sine wave inputJ05.2 IN1– Negative sine wave inputJ05.3 IN2 + Positive cosine wave inputJ05.6 PWM1 Positive carrier wave outputJ05.7 PWM2 Negative carrier wave outputJ05.8 IN2– Negative cosine wave inputShield PE Cable shield

At the connectors J03 and J04, analog current sensor signals can be connected.Signal Description

J03.1, J04.1 IN3+, IN4+ Positive current input signalJ03.2, J04.2 PE Cable shieldJ03.3, J04.3 IN3–, IN4– Negative current input signal

SLAU185 – August 2006 AMC1210EVM 1Submit Documentation Feedback

www.ti.com

1.2 Digital Interface

EVM Overview

J07 is a dummy connector for mechanical stability purposes only.

The inputs of the ADS104 are secured against voltage peaks through clamp diodes.

The AMC1210 modular EVM is designed for easy interfacing to multiple control platforms. Through theconnectors J09 and J08, the AMC1210 can be configured through a SPI interface from a F2812 type DSK.Signal Description

J08.1 CLK System clockJ08.2 SH2 Sample-and-hold signal 2J08.7 SH1 Sample-and-hold signal 1J09.3 SPICLK SPI clockJ09.7 SPISTE SPI frame syncJ09.11 SPIDIN SPI input dataJ09.13 SPIDOUT SPI output dataJ09.14 RST Asynchronous reset inputJ09.15 ACK Data acknowledge outputJ09.19 INT Interrupt output

Through J08, J09, J10, and J11, the AMC1210 can be configured through one of three differentmultiplexed parallel interface modes.Signal

(1)

Description

J08.1 CLK System clockJ08.2 SH2 Sample-and-hold signal 2J08.7 SH1 Sample-and-hold signal 1J09.14 RST Asynchronous reset inputJ10.1 CS Chip selectJ10.3 WR Write signalJ10.5 RD Read signalJ11.1 AD0 Address/databus bit 0 (LSB)J11.3 AD1 Address/databus bit 1J11.5 AD2 Address/databus bit 2J11.7 AD3 Address/databus bit 3J11.9 AD4 Address/databus bit 4J11.11 AD5 Address/databus bit 5J11.13 AD6 Address/databus bit 6J11.15 AD7 Address/databus bit 7 (MSB)J09.15 ACK Data acknowledge outputJ09.17 ALE Address latch enableJ09.19 INT Interrupt output

(1)

All even pin numbers of the connectors J10, J11, J12, and J15 are grounded.

All digital signals can be accessed through the connectors J12, J13, J14, and J15 on the top of theAMC1210 modular EVM. The different signals are placed at the same position as the bottom-mountedconnectors, see the preceding tables.

For higher frequencies on the CLK input of the AMC1210, it could be possible to reduce the value of theseries resistor R47.

AMC1210EVM 2 SLAU185 – August 2006Submit Documentation Feedback

www.ti.com

1.3 Power Supply

2 EVM Operation

EVM Operation

The AMC1210 modular EVM requires two supply voltages and two optional supply voltages. A 5-Vdcvoltage is needed for the ADS1204 and the core of the AMC1210. A variable supply in the range of 2.7Vdc to 5 Vdc is needed for the interface pins of the AMC1210. In addition, a ±15-V supply is necessary ifthe PWM driver operational amplifier OPA1632 is used. If the AMC1210 modular EVM is used incombination with the HPA-MCU Interface Board, J06 provides connection to the common power busdescribed in the document SLAU106 .

When used as a stand-alone EVM, the power supplies can be applied to J01 and J02. While filters areprovided for all four power supplies, optimal performance of the EVM requires a clean, well-regulatedpower source.

To configure a desired interface mode of the AMC1210 the jumpers JP09, JP10, and JP16 are used.Jumper Description

JP09 JP10 JP16

Open Open Open SPI interface modeOpen Closed Closed Parallel interface mode 1Closed Open Closed Parallel interface mode 2Closed Closed Closed Parallel interface mode 3 (Factory default condition)

The jumpers JP01, JP06, and JP11 determine the clocking scheme of the ADS1204.Jumper Description

JP01 JP06 JP11

1-2 Closed Open Open The ADS1204 gets the clock from AMC1210 pin CLK4.2-3 Closed Open Closed The ADS1204 gets the system clock. (Factory default condition)2-3 Closed Closed Open The ADS1204 works with its internal clock.

The jumpers JP07 and JP08 choose the driver of the PWM output pins for the resolver carrier signal.Jumper Description

JP07, JP08

1-2 Closed The PWM signal is driven directly from the AMC1210.2-3 Closed The PWM signal is driven by the operational amplifier OPA1632.(Factory default condition)

The AMC1210 can drive up to 100 mA directly from the pins PWM1 and PWM2. The purpose of theoperational amplifier OPA1632 is for the ability of filtering the carrier signal and still be capable of driving85 mA. If the OPA1632 operational amplifier is not used, the ±15-V supply can be left unconnected. In thiscase, it is recommenced to remove the resistors R24 and R26 to prevent latchup effects in the operationalamplifier and nonlinearities on the PWM outputs.

The jumpers JP02, JP03, JP04, and JP05 determine if the current sensor signals will be buffered orconnected directly to the ADS1204 inputs.Jumper Description

JP02, JP03, JP12, JP13,JP04, JP05 JP14, JP15

1-2 Closed Closed The current sensor signal is buffered. (Factory default condition)2-3 Closed Open The current sensor signal is unbuffered.

SLAU185 – August 2006 AMC1210EVM 3Submit Documentation Feedback

www.ti.com

3 AMC1210 Modular EVM Bill of Materials

AMC1210 Modular EVM Bill of MaterialsThe ADS1204 has a reference input pin for each channel and a reference output pin. This reference inputpin normally is direct connected to the 2.5-V reference output pin through a buffer and a RC-low-passfilter. If the input signal span is from either the resolver or the current sensor, a resistive divider can beadded to reduce the reference voltage at the input pin. The resistor R53 has to be soldered in to reducethe reference voltage for the resolver channels. The resistor R55 has to be soldered in to reduce thereference voltage for the current sensor channels.

The following table contains a complete bill of materials for the AMC1210EVM.Designators Description Manufacturer Mfg. Part Number

C01, C14, C16, C25, C034 10 µF, size A, tantalum, 16 V, 10% Kemet T491A106K016ASC02, C04, C06, C08, C09, 100 nF, 0805, ceramic, 50 V, 10%, X7R TDK C0805C104K5RACC15, C17, C18, C20, C22,C26–30, C35, C36, C44 C45C10–C13 22 pF, 0805, ceramic, 50 V, 10%, COG TDK C0805C220K5GACC19, C21 10 µF, size C, tantalum, 20 V, 10% Kemet T491C106K020ASC23, C24 1000 pF, 0805, ceramic, 50 V, 10%, X7R TDK C0805C102K5RACC31–C33, C43 33 µF, size D, tantalum, 16 V, 10% Kemet T491D336K016ASC37–C42 1 µF, 0805, ceramic, 16 V, 10%, X7R TDK C0805C105K4RACD01 Zener diode, 7.5 V, 1.3 W Fairchild BZX85C7V5D02,D03 Zener diode, 18 V, 1.3 W Fairchild BZX85C18D04–D09, D15, D16 Small signal diodes, SOT23 Fairchild BAV99D10–D13 LED, SMT 1206, Green Kingbright KPTD-3216CGCKD14 Zener diode, 5.1 V, 1.3 W Fairchild BZX85C_5V1F1-F4 (Optional - not installed Filter, EMI suppression, 0.5 MHz-1 GHz, 50 VDC, Murata BNX002-01on production EVMs) 10AMJ01-J04 3 Terminal screw connector OST ED1515J05 DB9, RTANG RECPT 0.318 W/ STD HDWR Assmann ADF09LLFJ06 (bottom side) 5 pin, dual row, SMT socket Samtec SSW-105-F-D-VS-KJ07–J10 (bottom side) 10 pin, dual row, SMT socket Samtec SSW-110-F-D-VS-KJ11(bottom side) 16 pin, dual row, SMT socket Samtec SSW-116-F-D-VS-KJ12(top side) 16 pin, dual row, SMT header Samtec TSM-116-01-T-DVJ13-J15(top side) 10 pin, dual row, SMT header Samtec TSM-110-01-T-DVJP01–JP05, JP07, JP08 3 Pin header Samtec TSW-103-07-L-SJP06, JP09–JP16 2 Pin header Samtec TSW-102-07-L-SR01, R04, R05, R08, R13, 10.0 Ω, 0805, 0.100 W, 1% Vishay/Dale CRCW080510R0FR16, R19, R22, R58, R59,R60–R65

R02, R03, R06, R07 4.99 k Ω, 0805, 0.10 W, 1% Vishay/Dale CRCW08054991FR11, R12, R14, R15, R17, 2.0 k Ω, 0805, 0.100 W, 1% Vishay/Dale CRCW08052001FR18, R20, R21, R24, R26,R52, R54R23, R28, R29, R51, R56, R74 10.0 k Ω, 0805, 0.100 W, 1% Vishay/Dale CRCW08051002FR25,R27 2.49 k Ω, 0805, 0.100 W, 1% Vishay/Dale CRCW08052491FR30–R39 200 Ω, 0805, 0.100 W, 1% Vishay/Dale CRCW08052000FR40–R46, R48, R72, R73 1.0 k Ω, 0805, 0.100 W, 1% Vishay/Dale CRCW08051001FR47 511 Ω, 0805, 0.100 W, 1% Vishay/Dale CRCW08055110FR53, R55 Not installedR57, R70, R71 100 k Ω, 0805, 0.100 W, 1% Vishay/Dale CRCW08051003FR66, R67 1.50 k Ω, 1206, 0.125 W, 1% Vishay/Dale CRCW12061501FR68 332 Ω, 1206, 0.125 W, 1% Vishay/Dale CRCW12063320F

4AMC1210EVM SLAU185 – August 2006Submit Documentation Feedback

www.ti.com

3.1 AMC1210 Modular EVM Schematic

AMC1210 Modular EVM Bill of Materials

Designators Description Manufacturer Mfg. Part Number

R69 511 Ω, 1206, 0.125 W, 1% Vishay/Dale CRCW12065110FU01 AMC1210 Texas Instruments AMC1210RHAU02 ADS1204 Texas Instruments ADS1204IU03 OPA4354 Texas Instruments OPA4354UU04 OPA2347 Texas Instruments OPA2347UAU05-U07 SN74LVC2G157 Texas Instruments SN74LVC2G157DCTU08 OPA1632 Texas Instruments OPA1632UA

The schematic diagram is shown on the following page.

SLAU185 – August 2006 AMC1210EVM 5Submit Documentation Feedback

EVALUATION BOARD/KIT IMPORTANT NOTICE

Texas Instruments (TI) provides the enclosed product(s) under the following conditions:This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATIONPURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling theproduct(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided arenot intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations,including product safety and environmental measures typically found in end products that incorporate such semiconductorcomponents or circuit boards. This evaluation board/kit does not fall within the scope of the European Union directives regardingelectromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet thetechnical requirements of these directives or other related directives.Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BYSELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDINGANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from allclaims arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility totake any and all appropriate precautions with regard to electrostatic discharge.EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHERFOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.

TI assumes no liability for applications assistance, customer product design, software performance, or infringement ofpatents or services described herein.

Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling theproduct. This notice contains important safety information about temperatures and voltages. For additional information on TI’senvironmental and/or safety programs, please contact the TI application engineer or visit www.ti.com/esh .No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, orcombination in which such TI products or services might be or are used.

FCC Warning

This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATIONPURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, andcan radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of thisequipment in other environments may cause interference with radio communications, in which case the user at his own expensewill be required to take whatever measures may be required to correct this interference.

EVM WARNINGS AND RESTRICTIONS

It is important to operate this EVM within the input voltage range of +15 V to -15 V and the output voltage range of 0 V to 5 V.Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there arequestions concerning the input range, please contact a TI field representative prior to connecting the input power.Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to theEVM. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the loadspecification, please contact a TI field representative.During normal operation, some circuit components may have case temperatures greater than 30 °C. The EVM is designed tooperate properly with certain components above 60 °C as long as the input and output ranges are maintained. These componentsinclude but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types ofdevices can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes nearthese devices during operation, please be aware that these devices may be very warm to the touch.

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.Customers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’sstandard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support thiswarranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarilyperformed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers shouldprovide adequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, maskwork right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or servicesare used. Information published by TI regarding third-party products or services does not constitute a license from TI to use suchproducts or services or a warranty or endorsement thereof. Use of such information may require a license from a third party underthe patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and isaccompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is anunfair and deceptive business practice. TI is not responsible or liable for such altered documentation.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or servicevoids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive businesspractice. TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product wouldreasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreementspecifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramificationsof their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-relatedrequirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding anyapplications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and itsrepresentatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade issolely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements inconnection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI productsare designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use anynon-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Amplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDSP dsp.ti.com Broadband www.ti.com/broadbandInterface interface.ti.com Digital Control www.ti.com/digitalcontrolLogic logic.ti.com Military www.ti.com/militaryPower Mgmt power.ti.com Optical Networking www.ti.com/opticalnetworkMicrocontrollers microcontroller.ti.com Security www.ti.com/securityRFID www.ti-rfid.com Telephony www.ti.com/telephonyLow Power www.ti.com/lpw Video & Imaging www.ti.com/videoWireless

Wireless www.ti.com/wireless

Inhaltsverzeichnis

Andere Texas Instruments Hauptplatine Handbücher

Texas Instruments

Texas Instruments MSP430FR58 Series Bedienungsanleitung

Texas Instruments

Texas Instruments bq25970 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS2543EVM Bedienungsanleitung

Texas Instruments

Texas Instruments DP159RGZ Bedienungsanleitung

Texas Instruments

Texas Instruments TPS65265EVM-705 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS65010EVM-230 Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8354EVM-PDK Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320DM6437 Bedienungsanleitung

Texas Instruments

Texas Instruments DLP NIRscan Bedienungsanleitung

Texas Instruments

Texas Instruments TPS55065EVM Bedienungsanleitung

Texas Instruments

Texas Instruments bq40z80EVM Bedienungsanleitung

Texas Instruments

Texas Instruments RF430F5978EVM Bedienungsanleitung

Texas Instruments

Texas Instruments ADS1174EVM Bedienungsanleitung

Texas Instruments

Texas Instruments LMR33640EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPS54202EVM-716 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS16630-32EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPS7A53EVM-031 Bedienungsanleitung

Texas Instruments

Texas Instruments ADS127L21EVM-PDK Bedienungsanleitung

Texas Instruments

Texas Instruments AWR2944EVM Bedienungsanleitung

Texas Instruments

Texas Instruments LM5185-Q1 Bedienungsanleitung

Texas Instruments

Texas Instruments BQ24351EVM Bedienungsanleitung

Texas Instruments

Texas Instruments DS90UB933-Q1EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPS92515HVEVM-749 Bedienungsanleitung

Texas Instruments

Texas Instruments TPD2E1B06DRLEVM Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung