Texas Instruments SmartRF CC900DBK Programmierhandbuch

Inhaltsverzeichnis

Andere Texas Instruments Hauptplatine Handbücher

Texas Instruments

Texas Instruments bq77905 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS65218EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPS65217CEVM Bedienungsanleitung

Texas Instruments

Texas Instruments DAC81404EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TCA9802 I2C Bedienungsanleitung

Texas Instruments

Texas Instruments TRF3722EVM Bedienungsanleitung

Texas Instruments

Texas Instruments LMG3411R150-031 Bedienungsanleitung

Texas Instruments

Texas Instruments BUF18830EVM Bedienungsanleitung

Texas Instruments

Texas Instruments bq25606 Bedienungsanleitung

Texas Instruments

Texas Instruments CC2510EMK Bedienungsanleitung

Texas Instruments

Texas Instruments LM63635DNEVM Bedienungsanleitung

Texas Instruments

Texas Instruments ADS7881EVM Bedienungsanleitung

Texas Instruments

Texas Instruments AN-1955 LM5009A Bedienungsanleitung

Texas Instruments

Texas Instruments ADS7861EVM Bedienungsanleitung

Texas Instruments

Texas Instruments ADC1xD1x00CVAL Series Bedienungsanleitung

Texas Instruments

Texas Instruments TPS65400 Bedienungsanleitung

Texas Instruments

Texas Instruments LDC131 Series Bedienungsanleitung

Texas Instruments

Texas Instruments TPS65132B Bedienungsanleitung

Texas Instruments

Texas Instruments TPS7A3301EVM-061 Bedienungsanleitung

Texas Instruments

Texas Instruments ADC32RF45 EVM Fehlerbehebungshandbuch

Texas Instruments

Texas Instruments DS280MB810EVM Bedienungsanleitung

Texas Instruments

Texas Instruments DS90UB933-Q1EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TAS5514BQ1DKDEVM Bedienungsanleitung

Texas Instruments

Texas Instruments UCC21220EVM-009 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung

SWRU063

Quick Start Instructions

Rev. 1.1

SmartRF

®

CC900DBK Demonstration Board Kit

SWRU063 Page 2 of 2

How to get a quick start using CC900DBK

The CC900DBK Demonstration Board Kit demonstrates the CC900 RF transceiver in a very

simple application. The Demonstration Board includes a complete CC900 transceiver, an

AVR micro-controller, an integrated PCB antenna and a battery. It provides a complete

example of a low-cost, low-power system using the CC900 transceiver. Please note that the

design is optimised for low cost applications and not for maximum range. In order to evaluate

range and performance, use the CC900DK.

Important:

•Do NOT short-circuit the battery terminals at any time.

•The use of radio transceivers is regulated by international and national rules. Before

transmitting a RF signal, please contact your local telecommunication authorities to check

if you are licensed to operate the transceiver.

To get the Kit up and running, follow these steps:

1. The CC900DB runs off a 3.6V Lithium battery. If the battery is not mounted, solder it to

the pads at the rear side of the board.

2. Examine the LED. If it does not blink at regular intervals, push the “ON” button.

3. If the LED still does not blink, remove the battery and reconnect it. If this does not help,

exchange the battery with a new one.

4. Press the “ON” buttons on both Demonstration Boards so that both are blinking. They are

now in polling reception mode, checking for data each time the LED is lit.

5. Press the “TX” button on one of the boards. The demonstration board sends a data

packet of approximately 1.5 second duration.

6. If the other demonstration board received the message without errors, its LED will blink

the Morse code for “victory”. It then sends an acknowledgement message in return.

7. If the first board receives the acknowledgement message, it will also blink “victory” in

Morse code.

If a demonstration board has not received a message or had any buttons pressed for two

minutes, it will enter power-down mode, ensuring minimum power consumption. To wake it,

press the “On” button.

If communication does not succeed on the first attempt, try again. RF noise may have

corrupted the message. Signal processing in the small micro-controller has been kept to a

minimum, therefore a small noise burst may corrupt the message. When holding the

demonstration board, do not touch the antenna or the VCO tank. Ideally, keep your hand as

far away from the antenna as possible in order to get the best performance. If you wish to

reprogram the Demonstration Board using the Development Kit, make sure to:

•Use the cable supplied in the Development Kit

•Remove the battery when reprogramming

•Use the correct parallel port. If you are using the correct port, you will receive an error

message if you try to program the EEPROM and no Demonstration Board is inserted

For further information, see the CC900DB Demonstration Board User Manual, which can be

downloaded from our website (http: www.chipcon.com)