Texecom ComGSM Bedienungsanleitung

ComGSM Module Installation Manual

INSTALLATION

MANUAL

GSM Communicator Module

Issue 1

THANK YOU FOR VOTING TEXECOM

ComGSM Module Installation Manual

2INS315

Introduction

The ComGSM module can be connected to the Premier 24/48/88/168/640 control

panels to provide the following facilities:

•Report system events (alarms, arm, disarm etc.) via text messaging to mobile

telephones

•Remotely arm, disarm and obtain current status of the alarm system via text

messaging

•High-speed modem communication for upload/download

The GSM module can only be used as a modem if the data service is

enabled by your network provider. Pay as you go tariffs generally do not

provide this feature.

ComGSM Layout

PCG0123456

234

Com1Engineer Keypad

Options

Audio

LOCK

123



ComGSM Module Installation Manual

INS315 3

Antenna connection

Tamper switch

Com1 data connection to Premier control panel

Engineer keypad connector (for future use)

Option switches (see table below)

Status LED’s (see table below)

Audio connector (for future use)

Heartbeat LED

SIM card socket

Option Switches

The option switches () function as follows:

Switch Off On

1 When the tamper is open, the GSM

signal is reported as NO signal GSM signal level is reported as normal

2 For future use – leave in OFF position

3 For future use – leave in OFF position

4 Toggle to perform a Reset

Status LEDs

The three status LED’s () indicate the following:

LED Off On Flashing

1 GSM NOT Ready GSM Ready GSM Communicating

2 Panel NOT Ready Panel Ready Panel Communicating

3 No GSM Signal Dim = Low Signal

Bright = Good Signal N/A

Installation

The ComGSM module should be installed as close to the control panel as possible, so

that the harness lead supplied with the unit is able to plug onto the control panel

communication port.

1. Route the harness lead into the module housing using the top left cable

entry and plug the connector onto COM1 ().

ComGSM Module Installation Manual

4 INS315

2. Install the module in the required location using suitable fixings.

3. Route the other end of the harness lead into the control panel housing.

DO NOT CONNECT at this point.

4. Connect the GSM antenna to the antenna connector on the module ()and site

the antenna as high as possible.

5. Unlock the SIM socket by sliding the locking tab downwards. Insert the SIM card

into the holder with the chamfered corner to the top left. Push the holder back

into position and lock the SIM by sliding the locking tab upwards.

The SIM card must be inserted before connecting the ComGSM module to

the control panel, and must not be removed until after the power supply to

the ComGSM module has been deactivated.

6. Set the option switches as required, see page 3.

7. Now connect the harness lead onto the control panel communication port (COM

2 for the Premier 24;COM 1 or 2 for the Premier 48/88/168/640).

8. The module should now be powered and the heartbeat LED () should be

flashing.

Panel Configuration

Before attempting to use the ComGSM module it must be correctly configured as

follows:

1. Enter “Engineers Programming” mode and select “UDL/Digi Options”, then

select “Com Port Setup”. Ensure Com Port is programmed as “GSM Module”.

2. Now select the “Digi Options” menu and make sure that “Digi Option 1” is

programmed for “Digi is Enabled”.

3. Now select “Program Digi” and ensure the following options are programmed for

one of the ARC options:

a) Protocol: “SMS Messaging”.

b) Primary No: The number of the recipients mobile telephone.

c) Secondary No: Secondary mobile telephone number (if required).

d) Account No: Leave blank.

e) Dialling Attempts: Program as required.

f) Report Areas: Program as required.

g) Reports: Program as required.

h) Config.: Program as required.

4. All three status LED’s should now be on, if status LED 3 is dim, this indicates a

low GSM signal level. If the signal level is low, try moving the antenna to improve

the reception.



ComGSM Module Installation Manual

INS315 5

Using the SMS Control Commands

Control commands can be sent to the ComGSM module to allow remote control and

integration of the alarm system.

1. Select the send text message option on your mobile telephone.

2. Enter the telephone number of the ComGSM module.

3. Enter the text command, see SMS Control Commands.

4. Select send on your mobile telephone.

When using the SMS Control Commands shown in the tables below the following

should be noted:

???? = User code, this must proceed all commands.

[areas] = Areas 1 to 8 or A to P. If the areas are not specified then all areas will be

selected.

[s] = Send back status report

(zones) = List of zones, each zone must separated by a space e.g. 1 12 167 etc.

(outputs) = List of outputs, e.g. 1234 etc.

(message) = A maximum of 32 characters.

Premier 24 SMS Control Commands

Operation Command Example

Arm System ???? arm [s] “5678 arm s” = arm the system and report back

status.

Part Arm System ???? parm (1/2/3) [s] “5678 parm 1” = part arm 1 the system (no status)

Disarm System ???? darm [s] “5678 darm” = disarm the system (no status).

Reset System ???? reset “5678 reset” = reset the system

Turn Outputs On ???? op on (outputs) [s] “5678 op on 2” = turn PC output 2 on.

Turn Outputs Off ???? op off (outputs) [s] “5678 op off 1 s” = turn PC output 1 off and report

back status.

Send Message ???? mess (message) “5678 mess How Are You” = Displays How Are

You on all keypads.

System Status ???? status

“5678 status” =

System (Disarmed or Armed)

PC Output 1 ON

PC Output 2 ON

ComGSM Module Installation Manual

6 INS315

Premier 48/88/168/640 SMS Control Commands

Operation Command Example

Arm System ???? arm [areas][s] “5678 arm s” = arm all areas and report back

status.

Part Arm System ???? parm (1/2/3)[s] “5678 parm 1” = part arm 1 all areas (no status)

Disarm System ???? darm [areas][s] “5678 darm abcs” = disarm areas abc and report

back status.

Reset System ???? reset [areas] “5678 reset” = reset all areas

Omit Zone(s) ???? omit (zones) “5678 omit 1 5 12” = omit zones 1, 5 and 12

Unomit Zone(s) ???? uomit (zones) “5678 uomit 12” = reinstate zone 12

Turn Outputs On ???? op on (outputs)[s] “5678 op on 134” = turn PC outputs 1, 3 and 4 on.

Turn Outputs Off ???? op off (outputs)[s] “5678 op off 4s” = turn PC output 4 off and report

back status.

Send Message ???? mess (message) “5678 mess How Are You” = Displays How Are

You on all keypads.

System Status ???? status

“5678 status” =

Armed: (1 - 8 or A - P)

Alarm: (1 - 8 or A - P)

Output: (1 - 8)

Mains: (OK or Fault)

Battery: (OK or Fault)

Phone Line: (OK or Fault)

Output Status ???? status O

“5678 status O” =

Armed: (1 - 8 or A - P)

Alarm: (A - P)

Channels: (1 - 8)

Digi: (1 - 8)

Panel: (1 - 5)

Mains: (OK or Fault)

Battery: (OK or Fault)

Phone Line: (OK or Fault)

GSM/Radio-Pad

Status ???? status R

“5678 status R” =

Serial: ####### (only if Radio-Pad fitted)

NUA: ###### (only if Radio-Pad fitted)

FSS: ### (only if Radio-Pad fitted)

RSS: ### (only if Radio-Pad fitted)

BER: ### (only if Radio-Pad fitted)

CRC: ### (only if Radio-Pad fitted)

GSM-Signal: ###

GSM-BER: ###

ComGSM Module Installation Manual

INS315 7

What will be sent in the Text Message

The following information will be received in the text message:

3 W e s t e r n R o a d

12:45.58 01/12

Zone 003Alarm

The Detector in

the Lounge

Area:A.......

My Home

Up to 16 characters of text (this is the Printer Header)

Time and Date

EventType

Zone/Username text

Area that caused the event

Name programmed into phone

Specifications

Electrical

Supply: 9 to 14VDC

Current Consumption: 35mA quiescent; 100mA when active

Environmental

Operating Temperature: -10°C to +55°C

Maximum Humidity: 95% non-condensing

Physical

Dimensions: 170mm x 140mm x 35mm

Packed Weight: 200g (approx.)

Standards

The Premier ComGSM module conform to European Union (EU) Low Voltage Directive

(LVD) 73/23/EEC (amended by 93/68/EEC) and Electro-Magnetic Compatibility (EMC)

Directive 89/336/EEC (amended by 92/31/EEC and 93/68/EEC). The CE mark indicates

that this product complies with the European requirements for safety, health,

environment and customer protection.

This product is suitable for use in systems designed to comply with PD 6662: 2004

(prEN 50131-1: 2004) at Grade 3 and Environmental Class II.

Warranty

All Texecom products are designed for reliable, trouble-free operation. Quality is

carefully monitored by extensive computerised testing. As a result the Premier

ComGSM module is covered by a two-year warranty against defects in material or

workmanship. As the Premier ComGSM module is not a complete alarm system but

only a part thereof, Texecom cannot accept responsibility or liability for any damages

whatsoever based on a claim that the Premier ComGSM module failed to function

correctly. Due to our policy of continuous improvement Texecom reserve the right to

change specification without prior notice. Premier is a trademark of Texecom Ltd.

Texecom Limited, Bradwood Court, St. Crispin Way, Haslingden, Lancashire BB4

4PW, England.

Technical Support:

Tel: +44 (0)1706 234833; Tel: +44 (0)1706 234811; Fax: +44 (0)1706 213187

©Texecom Ltd 2006

INS315

Inhaltsverzeichnis

Andere Texecom Sicherheitssystem Handbücher

Texecom

Texecom Premier Elite Impaq Contact-W Bedienungsanleitung

Texecom

Texecom PREMIER 640 Bedienungsanleitung

Texecom

Texecom Speech Dialler Bedienungsanleitung

Texecom

Texecom INS555-3 Bedienungsanleitung

Texecom

Texecom PREMIER 640 Bedienungsanleitung

Texecom

Texecom Premier Elite Series Bedienungsanleitung

Texecom

Texecom Speech Dialler Bedienungsanleitung

Texecom

Texecom Premier Elite 8XP-W Bedienungsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Texecom

Texecom Azura 360 Bedienungsanleitung

Texecom

Texecom Ricochet Impaq Contact-W Bedienungsanleitung

Texecom

Texecom Premier 24 Bedienungsanleitung

Texecom

Texecom Premier Elite 8XP-W Bedienungsanleitung

Texecom

Texecom Premier Elite 8XP-W Bedienungsanleitung

Texecom

Texecom Premier Elite Series Bedienungsanleitung

Texecom

Texecom PrestigeCompact IR Bedienungsanleitung

Texecom

Texecom Premier Elite 8XP-W Bedienungsanleitung

Texecom

Texecom Premier Elite Impaq Contact-W Bedienungsanleitung

Texecom

Texecom Premier Elite iProx Bedienungsanleitung

Texecom

Texecom Ricochet Impaq Contact-W Bedienungsanleitung

Texecom

Texecom Veritas Excel Master Bedienungsanleitung

Texecom

Texecom Premier 412 Betriebsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Texecom

Texecom Premier Elite Series Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung