Textron Jacobsen SLF530 Betriebsanleitung

SLF530™

Super Lightweight

Fairway Mower

Repair Manual

WARNING: If incorrectly used this machine can cause severe injury. Those

who use and maintain this machine should be trained in its proper use,

warned of its dangers and should read the entire manual before attempting to

set up, operate, adjust or service the machine.



This manual may not re reproduced in whole or in part without the

express permission of TSV (Augusta) Technical Communications

Department.

673831-Rev A 3

Foreword

General

This manual provides detailed information and

procedures to safely repair and maintain the following:

Jacobsen SLF530 Super Lightweight Fairway

mowers and associated accessory attachments

This manual is intended to introduce and guide the user

through the latest factory-approved troubleshooting and

repair techniques and practices.

Before you attempt to troubleshoot or make repairs, you

must be familiar with the operation of this machine. Refer

to the operator’s manual and parts manual for specific

information on these topics.

THE INFORMATION CONTAINED IN THIS MANUAL IS

BASED ON MACHINES MANUFACTURED UP TO THE

TIME OF PUBLICATION. JACOBSEN RESERVES THE

RIGHT TO CHANGE ANY OF THIS INFORMATION

WITHOUT NOTICE.

California

Proposition 65 Warning



WARNING

Trademark Acknowledgement

Jacobsen acknowledges the following trademarks for

company names or products mentioned within this

publication:

Lubriplate®is a trademark of Fiske Brothers Refining Co.

Loctite®and Permatex®are trademarks of Henkel

Corporation.

Certain vehicle components contain or emit

chemicals known to the State of California to

cause cancer and birth defects or other

reproductive harm.

4673831-Rev A

FOREWORD

How to Use This Manual

This manual is designed to provide multiple ways to

locate and access repair information.

Read each section in entirety before beginning a

procedure. Proper understanding of machine operation

and components is the key to successful diagnostics and

repair.

Make use of special information features with in this

manual in order to be better prepared to perform repairs.

Always follow manual procedures and safety guidelines.

Never take shortcuts.

Table of Contents

Major machine components or topics of interest are

separated into specific chapters. Each manual lists these

chapters in a main Table of Contents.

Chapter Table of Contents

Each chapter begins with a detailed Table of Contents

related to the specific machine component or system.

Use the Chapter Table of Contents to find specific

component or procedural information.

Index

An alphabetical Index is located at the back of the

manual.

Use the Index to find specific components and related

procedures.

Required Tools and Materials

Some procedures will require the use of specific tools

and/or materials. These tools and/or materials will be

listed for reference, prior to beginning a procedure.

Specifications

Near the beginning of each chapter is a specifications

listing. This listing contains any specifications contained

within the chapter.

Quick Reference Specifications

A list of all machine specifications can be found in

Chapter 2 Specifications and General Information. This is

a list of all specifications from each chapter, combined

and listed in one place for easy reference.

Warnings and Cautions

Warning and Caution indicators are located throughout

the manual at specific points of interest. These notices

are given to prevent personal injury, death and/or

equipment damage. Always heed these notices, and

practice common sense when performing any

maintenance or repair procedure.

Notes

Special notes are given in order to draw attention to

detailed instructions. These notes are intended to give

further important information regarding the machine

and/or a step in a procedure.

Troubleshooting

Troubleshooting charts are provided in each chapter to

aid in the diagnostic process. Use these suggestions to

aid in identifying a potential mechanical or machine

adjustment problem.

Table of Contents

673831-Rev A 5

Safety

Specifications and

General Information

Engine

Electrical

Hydrostatic Power Train

Hydraulics

Steering

Cutting Units

Accessories and Miscellaneous

Repair

673831-Rev A 1-1

Chapter 1

Safety

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Prepare for the Job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Safety Label Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Inspect Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Keep Work Area Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Keep Work Area Well Ventilated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Use Proper Eye and Face Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Park Mower Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Use Lifting Equipment Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Support Machine Securely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Use Compressed Air and Air Tools Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Service Tires Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Handle Fuel Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Store Volatile and Hazardous Materials Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Handle Chemical Products Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Service Hydraulic System Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Service Cooling System Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Service Electrical Components Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Dispose of Waste Materials Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

1-2 673831-Rev A

SAFETY

Introduction

Safety is the most important element of any repair

procedure. Knowledge of the procedure to be performed

and safe work habits are essential to preventing death,

personal injury, or property damage. Use the following

statements as a common-sense guide to proper work

and tool-use habits.

Prepare for the Job

Preparation is essential to complete a procedure in a

safe and efficient manner.

• Wear proper clothing. Loose or baggy clothing could

become tangled in moving parts.

• Use eye/face protection. Always use proper eye/face

protection to protect your eyes from flying debris or

chemical splatters.

• Wear protective footwear. Wear safety shoes

(steel-toe) to protect your feet from falling objects.

• Use gloves when handling parts. Parts may have

sharp edges or may be hot.

• Remove jewelry prior to servicing electrical systems.

• Prepare proper tools and equipment. Always use the

correct tool for the job. Improper or homemade tools

can cause injury or machine damage.

• Prepare needed parts and materials. Gather the

needed parts and materials before beginning the

procedure.

• Allow machine to cool. Many components can get hot

during operation. Be sure to allow enough time for

components to cool before beginning service.

• Prepare proper work-space lighting. A well-lit work

area can make the job easier.

• Follow procedures and safety warnings. Service

procedures are written to be as safe and efficient as

possible. Never take shortcuts.

• Be prepared for emergencies. Accidents can happen,

even under the best conditions. Fire extinguishers

and first aid kits should be well maintained and easily

accessible.

Safety Notices

Throughout this manual, the following key safety words

will be used to alert the reader of potential hazards.

Become familiar with these words and their meaning.

Take all precautions to avoid the hazards described.



DANGER



WARNING



CAUTION

NOTICE

Safety Label Locations

Become familiar with machine safety labels and

locations. The following illustrations show safety label

locations on the machine.

See Figure 1-1.

This safety alert symbol is used to

alert you to potential hazards.

Indicates an imminently hazardous situation

which, if not avoided, WILL result in death or

serious injury.

Indicates a potentially hazardous situation which,

if not avoided, COULD result in death or serious

injury.

Indicates a potentially hazardous situation which,

if not avoided, MAY result in minor or moderate

injury and property damage. It may also be used

to alert against unsafe practices.

Indicates a potentially hazardous situation which,

if not avoided, MAY result in property damage. It

may also be used to alert against unsafe

practices.



SAFETY

673831-Rev A 1-3

Figure 1-1

MAR0230

1-4 673831-Rev A

SAFETY

009034880

4181865 REV B

2 3 4 6 7

20°+

4262591

S≤15 mg/kg

4324674

4397486

10 11

Inhaltsverzeichnis

Andere Textron Rasenmäher Handbücher

Textron

Textron JACOBSEN RC466 Einrichtungshandbuch

Textron

Textron BUNTON BZT 2000 Series Gebrauchs- und Pflegehandbuch

Textron

Textron RANSOMES FRONT-LINE 933 Technische Daten

Textron

Textron JACOBSEN G-PLEX III DN Leitfaden

Textron

Textron Jacobsen Super LF 1880 Fairway Mower with... Leitfaden

Textron

Textron Jacobsen Ransomes Parkway 3 Meteor LGNN344 Leitfaden

Textron

Textron JACOBSEN R-311 69166 Bedienungsanleitung

Textron

Textron Jacobsen R311T-T4I Leitfaden

Textron

Textron JACOBSEN GP400 Bedienungsanleitung

Textron

Textron Ransomes 933303H Bedienungsanleitung

Textron

Textron JACOBSEN PGM Series Bedienungsanleitung

Textron

Textron Jacobsen HR-5111 Bedienungsanleitung

Textron

Textron JACOBSEN GP400 Leitfaden

Textron

Textron Jacobsen PB Series Leitfaden

Textron

Textron Jacobsen DH Series Leitfaden

Textron

Textron Jacobsen Greens King VI 62376 Leitfaden

Textron

Textron Jacobsen Tri-King 67139 Bedienungsanleitung

Textron

Textron RANSOMES Bedienungsanleitung

Textron

Textron JACOBSEN MC400 Einrichtungshandbuch

Textron

Textron Ransomes Mastiff 91 Series Leitfaden

Textron

Textron Ransomes Jacobsen Super Certes 51 Leitfaden

Textron

Textron Jacobsen HR 9016 Turbo Bedienungsanleitung

Textron

Textron RANSOMES 933407 Leitfaden

Textron

Textron JACOBSEN R-311 Leitfaden

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

Craftsman

Craftsman 917.378461 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung