TGS DAISY Series Bedienungsanleitung

DAISY™

INSTALLATION INSTRUCTIONS

52-INCH INDOOR LED CEILING FAN

www.trulygreensolutions.com

Dimension Reference:

Hardware Package Included:

Fan Parts Included:

5-1/4 in

2-1/2 in

10-3/4 in

18-1/2 in

52 in

Hardware Package

16Paper Washers.

S11

S12

3Bracket Screw.

S11.

S12

3. Canopy

4. Coupler Cover

7. Glass

5. Fan Motor Assembly 1

Bulb

Blade Arm

10. Fan Blade 5

www.trulygreensolutions.com

Exploded View:

Support Rod

Safety Pin

Cotter Pin

Ceiling Canopy

Canopy Screws

Mounting Bracket

Motor Coupler

Fan Motor

Assembly

Switch Housing

Three Speed Switch

Pull Chain

Glass

Bulb

Light Switch Pull Chain

Coupler Cover

Blade Arm

Blade

Blade Arm Screws

Fiber Washer

www.trulygreensolutions.com

supplied by the person(s) installing, caring for and operating fan.

common sense, caution and care are factors which can not be built into this product. These factors must be

are not meant to cover all possible conditions and situations that may occur. It must be understood that

•

NOTE: The safeguards provided by these safety instructions and by any separate installation instructions

necessary.

grease and permanently sealed at the factory so that, under normal conditions, further attention is not

•

Lubrication of your new ceiling fan is not necessary. The ball bearings have been adequately charged with

refer to a do-it-yourself wiring handbook or hire a qualified electrician to install your fan.

You could however, encounter situations or problems not covered in this manual. Should this occur, please

•

Every effort has been made to provide you with proper instructions for the safe installation of this ceiling fan.

finish...and will VOID YOUR WARRANTY.

high humidity. Installation in this type of location could be UNSAFE, will most likely damage the fan and its

•

This ceiling fan was not designed for installation in any location where it might be exposed to moisture or

the ceiling.

any point in its rotation and a minimum of 7 feet from blade level to floor and 10 inches from the blades to

•

The location you choose should have a minimum clearance of 20 inches from any wall to the blade tip at

necessary

products for the proper and safe installation of your ceiling fan.

hardware and do-it-yourself centers. In most cases your Truly Green Solutions dealer will have all the

Support”. If you have any questions, outlet boxes and support systems for ceiling fans are available at most

it is securely attached and able to support at least 50 pounds of moving weight marked “Acceptable for Fan

•

If you plan to use an existing electrical location check to make sure that the outlet box is not PLASTIC, that

Support”

(Plastic outlet boxes are not recommended for ceiling fan installation).

box should be able to support a minimum moving weight of 50 pounds and marked “Acceptable for Fan

electrician to run the wiring and install an outlet box designed for ceiling fans or heavy fixtures. The outlet

•

If the location where you plan to install your fan does not already have an electrical outlet, hire a licensed

amp breaker or fuse. Make sure that your electrical system and choice of location meet these requirements.

•

Basic requirements for a ceiling fan installed with lights are 120V AC-60Hz on a grounded circuit with a 15

connections. Plastic electrical tape is not recommended.

of the codes and wire the fan accordingly. Never leave bare wire uncovered, use wire nuts to cap all

•

Make sure that all wiring conforms to national and local electrical codes. If you are in question obtain a copy

installing or servicing this fixture.

•

To avoid the risk of electrical shock be sure to shut off power at the main fuse or circuit breaker box before

INSTALL

YOUR NEW CEILING FAN. SAVE INSTRUCTIONS.

ELECTRICAL WIRING PROCEDURES WE RECOMMEND THAT YOU HAVE

QUALIFIED ELECTRICIAN

THE FAN. IF YOU ARE NOT FAMILIAR WITH NATIONAL AND LOCAL ELECTRICAL CODES AND BASIC

READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING

Safety

Instructions:

• To reduce the risk of fire, electrical shock, or personal injury, mount this fan to an outlet box marked

“Acceptable for Fan Support of 22.7 kg ( 50 lbs )” or less and use Mounting Screws provided with the outlet

box. CAUTION: Install the primary mounting means and use only the hardware provided with the fan.

• To reduce the risk of personal injury take care not to bend the blade brackets when installing the brackets,

balancing the blades or cleaning the fan. Be careful not to insert foreign objects in between rotating fan

blades.

• To reduce the risk of fire or electrical shock, do not use this fan with any solid-state speed control device.

• The important safeguards and instructions appearing in this manual are not meant to cover all possible

conditions and situations that may occur. It must be understood that common sense, caution and careful

attention to detail are factors which cannot be built into this product. These factors must be supplied by the

person or persons installing, caring for, and operating the unit.

Warning:

Installation Instructions:

Back off (loosen) the set screws (2) in the support rod coupler

until the inside of the channel is clear of the screw tip. Remove

and save the safety pin and washer on the end of the support

rod assembly. Slide the ceiling canopy onto the support rod,

followed by the support rod coupler cover (see figure 1). Feed

the electrical wires from the fan housing through the support rod.

Thread the support rod into the support rod coupler until the

safety pin can be inserted through the hole in both the rod and

coupler. Insert the safety pin through the hole in the support rod

coupler and support rod then attach washer into safety pin and

the retaining clip on the other side. Tighten both set screws and

safety screw on the support rod coupler.

Step 1 Assemble Fan Support Rod

Note: If support rod is already assembled in the box, skip this step.

FIG 1

Support Rod Coupler

Support Rod

Ceiling Canopy

Coupler Cover

Cotter Pin

Safety Pin

www.trulygreensolutions.com

Step 3 Hanging the Fan Body

Notice the half ball on the end of the support rod is grooved down one side (see

figure 5). This keyway fits over the small keyway pin on the inside of the mounting

bracket and keeps the ceiling fan from spinning on the mounting bracket.

Using your step ladder, lift the fan and place the half ball in the center of the

mounting bracket with the keyway pin inserted into the keyway on the ball. Turn the

fan left and right slightly to make sure it is seated on the bracket with the keyway

pin in the keyway (see figure 6).

FIG 5

FIG 6

Step 2 Install Mounting Bracket

Remove the two non-slotted mounting screws on the top of the canopy.

Back the two slotted screws out about half way. This will enable you to

remove the mounting bracket from canopy (see figure 2).

Install the mounting bracket onto the electrical junction box in the ceiling

using two machine screws, two washers and two lock washers (see figure

3).

The mounting bracket has slotted holes to enable it to move sideways for

proper alignment. Make sure the mounting bracket is centered over the

electrical junction box and that it is securely attached (see figure 4).

NO MOVEMENT SHOULD OCCUR BETWEEN THE MOUNTING

BRACKET AND THE ELECTRICAL JUNCTION BOX.

Pull the electrical wires in the junction box down and through the mounting

bracket.

Junction Box

Mounting Bracket

Non-Slotted

Screw

Slotted Screw

Canopy

FIG 3

FIG 4

FIG 2

Slotted Holes

Mounting Bracket

Keyway Pin

Ball Hanger

Support Rod

Mounting

Bracket

Keyway Pin

Ball Hanger

Support Rod

www.trulygreensolutions.com

FIG 7

Trim the lead wires, leaving about six inches of each wire extending from the

support rod (see figure 7).

Step 3 Hanging the Fan Body (continued...)

Ball Hanger

Ground Wire

Support Rod

Step 4 Making the Electrical Connections

To operate your ceiling fan with the pull chain(s) and switches mounted on your

fan, follow the instruction below (see figure 8-1).

Attach the GREEN wire (connected to the half ball) to the GROUND wire in the

junction box. The GROUND wire is usually a bare copper wire without plastic

insulation. It could also be covered in green plastic insulation.

Attach the BLACK wire and BLUE wire from the ceiling fan to the BLACK wire in

the junction box.

Attach the WHITE wire from the ceiling fan to the WHITE wire in the junction box.

Fold the connected wires (see figure 8-2) and push them up inside the electrical

junction box with the BLACK and BLUE wires to one side and the WHITE and

GREEN to the other side. Make sure the wire nuts do not come loose during this

operation.

FIG 8-1

FIG 8-2

Black

Blue

Green

White

Black

Blue

White

Green

Mounting

Bracket

Canopy

Step 5 Secure Canopy

Slide the ceiling canopy up into place over the ceiling mounting bracket. Loosen

up the canopy screws on the side of the mounting bracket. Line up the J Slots

with the canopy screws. Press the canopy against the mounting bracket and

turn it clockwise. Tighten screws on the J Slots and install the two screws in the

remaining holes (see figure 9).

FIG 9

www.trulygreensolutions.com

Maintenance:

Your fan requires very little maintenance. Cleaning of the housing should be done with a damp soft cloth (NO CLEANING AGENTS). On the

blades, use a duster or dry cloth because any moisture could cause the blades to warp.

Conforms To D.O.E. EPACT Regulation

Step 7 Installation of Lighting Fixture

If applicable, remove switch housing cover and attach light

fixture. Connect white wire to white wire and blue wire to black

wire with wire nuts.

Attach switch housing plate to switch housing shell using

supplied screws and tighten firmly .

Slide glass shade over sockets and tighten set screws until

snug to glass. Twist bulbs into socket, DO NOT over tighten.

(see figure 11).

FIG 10

Step 6 Blade And Blade Arm Assembly

Bulb

Light Switch

Pull Chain

Glass

Shade

Set Screws

FIG 11

White

Black

Blue

Forward/Reverse Switch

Switch Housing Shell

Fan Switch Pull Chain

Switch Housing

Screw

Fan Blade Screw

Motor Housing

Fiber Washer

Lightly attach each blade to the blade arm by using 3pcs

screws and fiber washers as shown in figure 10. Tighten each

screw. Make sure the blade is straight.

Attach each blade assembly to motor aeembly by using 2pcs

provided screws. Then securely tighten after the screws are

attached, Repeat this procedure for all blades. (see figure 10)

Be careful not to bend the blade arms during installation. This

will cause your fan to wobble while running.

www.trulygreensolutions.com

Operation:

The pull chain located on the switch housing controls the speed of your fan. When the fan is OFF, pull the chain once for HIGH

speed, twice for MEDIUM speed, three times for LOW speed and a fourth time to turn it off again.

Turn fan completely off before moving the reverse switch. Set

reverse switch to recirculate air depending on the season: UP

position in summer (1), OWN position in winter (2). IMPORTANT: If

the reverse switch is set in the (3) middle position the fan will not

operate. Attach the pull chain extensions supplied or custom pull

chains (sold separately) to ends of the pull chains.

2. 3.

Optional Wiring Diagrams:

Figure 12 illustrates the wiring used to control the fan with a wall

switch plus an optional light fixture controlled at the fixture.

Figure 13 illustrates the wiring used to control fan with the pull

chain on the electrical switch housing plus an optional light fixture

with a wall switch.

Figure 14 illustrates the wiring used to control the fan and optional

light fixture with separate wall switches.

Your dealer carries a number of different types of wall switches

that have been designed and tested for use with our products.

If you elect to control the motor of your ceiling fan from a wall

switch, remember that the wall switch will only turn your fan ON or

OFF. The speed is adjusted at the fan.

If you elect to control the speeds of your ceiling fan from a wall

switch, YOU MUST set the speed switch on the ceiling fan to

HIGH speed and leave it in that setting.

FIG 12

FIG 13

FIG 14

Reverse switch

www.trulygreensolutions.com

Troubleshooting Guide:

cases these installation errors may be mistaken for defects. If you experience any faults please check this troubleshooting guide.

Problem Suggested Remedy:

1. If fan does not start:

1. Check main and branch circuit fuses or circuit breakers.

2. Check line wire connections to fan and switch wire connections in switch housing. CAUTION:

switch is in the middle.

4. Make sure that the wall controller is turned “ON”.

2. If fan sounds noisy:

1. Make sure all screws in motor housing are snug (not over tightened).

2. Make sure the screws which attach the fan blade holder to the motor are tight.

3. Make sure wire nut connectors in switch housing are not rattling against each other or against

the interior wall of the switch housing.

4. If using an optional ceiling fan light kit check to be sure the screws securing the glass shade are

tight. Check to be sure the light bulb is tight on the socket and not touching the glass shade.

5. Some fan motors are sensitive to signals from solid state variable speed controls. DO NOT USE a

solid state variable speed control.

6. Your ceiling fan’s “break in” period is 24 hours of operation. Most noises associated with a new

fan will disappear after this period.

3. If fan wobbles:

All blades are weighed and grouped by weight. Natural woods vary in density which could

cause the fan to wobble even though all blades are weight-matched. The following procedures

should eliminate most of the wobble. Check for wobble after each step.

2. Check that all blade holders are tightened securely to motor.

3. Make sure that canopy and mounting bracket are tightened securely to ceiling junction box

4. Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades keeping measure within 1/8

in. Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. If

all blade levels are not equal you can adjust blade levels by the following procedure. To adjust a

blade tip down insert a washer (not supplied) between the blade and blade holder at the screw

closest to the motor. To adjust a blade tip up insert washer (not supplied) between the blade

and blade holder at the two screws farthest from the motor.

5. If blade wobble is still noticeable interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

4. If light does not work:

1. Check blue wire from fan to make sure it is connected to hot wire from the house.

2. Check for loose or disconnected wires in fan switch housing.

3. Check for loose or disconnected wires in light kit.

switch housing.

on power to the fan using the pull chain, wall switch, or remote control (whichever is installed

on the particular fan).

www.trulygreensolutions.com

Inhaltsverzeichnis

Andere TGS Lüfter Handbücher

TGS

TGS BEVERLY Series Bedienungsanleitung

TGS

TGS HELEN Series Bedienungsanleitung

TGS

TGS DIANA Series Bedienungsanleitung

TGS

TGS AVIO Series Bedienungsanleitung

TGS

TGS SALEM Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung