Thermaltake C240 Bedienungsanleitung

C240 DDC SOFT TUBE LIQUID COOLING KIT

Intel LGA 775,LGA115x,LGA1366

Intel LGA2011,2011-3

AMD

1.FM2/FM1/AM3/AM2

2.AM4

3.LGA1366

4.LGA1150/1151/1155/1156

5.LGA775

CPU Water Block Installation Guide

www.thermaltake.com

01 01

1 3

C240 DDC SOFT TUBE LIQUID COOLING KIT

Installation Guide

To ensure a clean loop, flush and rinse your radiators

and water blocks with distilled water before using.

Make sure the fittings are screwed securely when

placing them onto the radiator.

Attach the fittings to the inlet and outlet of the water block.

Radiator Water Block

Installation Walkthrough (Example: A500 TG)

Place the motherboard into the case. Position the radiator. Attach the pump and reservoir into

the chosen locations.

Attach the fans to the radiator

Case Fan

Connect the PWM

cable to motherboard. 31

Connect the fan power cable to PWM cable

2031

Connect the fan power cable when the liquid cooling system

is completely finished

CAUTIONS:

Make sure there is enough space when you start to set up the LCS product

12 12

Attach fittings onto the pump and reservoir

Pump / Reservoir

Choose the proper way to mount the pump and reservoir by referring to the manual

(suggest vertical placement)

C240 DDC SOFT TUBE LIQUID COOLING KIT

Thermaltake recommends the following steps to be taken after completing your water loop setup

1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance

while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.

2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.

3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately

4. Fill the reservoir to the top as it will prevent air from going into the pump

5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.

6. Place some paper towels under fittings and joining points to test for leaks.

7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.

Cutting and Attaching the Tubing

Filling the System

CAUTIONS:

1. Before filling the system, please make

sure that each fitting as well as unused

ports are completely sealed.

2. If there is any case of leaking,

immediately turn off the power and

clean the leak

3. If there is any related electronic parts

stained on liquid coolant, make sure to

completely clean and dry the

components. And then make sure they

all work well.

After switching off the power supply,

connect the PSU power cord and

product cables.

Use the refill bottle to fill coolant into the reservoir

Place your PSU outside of the case and attach it to

the pumps 4pin molex connector, turn on the power

of PSU and make the rest of the system fills up.

34 35

Take out the cap from the fittings and place

the cap of the compression fitting over the

tubing. Push the end of the tubing over the

barb; make sure the tubing is a tight fit.

Slide the cap over the fitting and rotate it

clockwise until the tubing is sealed in place.

Measure the tube length based on the fitting,

and make (cut) the tubes. The loop order :

Pump Outlet > Water Block

Measure the tube length based on tfitting,

and make (cut) the tubes. The loop order :

Water Block > Radiator

Measure the tube length based on the

fitting, and make (cut) the tubes.

The loop order : Radiator > Reservoir inlet

C240 DDC SOFT TUBE LIQUID COOLING KIT

Motherboard SYNC installation Guide

CAUTIONCAUTION

1. Light Mode:

Switch over between 7 LED modes.

3. Light Speed:

Switch over between 4 light modes.

When light mode is in RGB Spectrum:

Click to memorize and lock the color you want, click again to unlock the 256

colors auto rotation.

Red → Yellow → Green → Teal → Blue → White → Purple

When light mode is in Ripple :

Switch over 7 LED colors .

When light mode is in Wave and Flow :

LED color can not be adjusted.

Red → Yellow → Green → Teal → Blue → White → Purple → Rainbow

2. Color Mode:

When light mode is in Full Lighted, Pulse and Blink :

Switch over 8 LED colors .

Wave → Full light → RGB Spectrum → Off → Flow → Ripple → Pulse → Blink

Slow → Normal → Fast → Extreme

Connect the Motherboard Signal Bridge Cable to fan led cable

Please power off the PC and check

the Positive and Negative ends on

the connector before connecting

the cable to motherboard. Connecting

the wrong end can damage the LEDs.

Aura Addressable Strip Header(s) Addressable RGB LED Header(s) AORUS RGB Fusion with Digital LEDs

ASUS ASROCK GIGABYTE

JRGB-strip Header(S)

MSIMSI

+5V D G

JRAINBOW

Connect the ARGB controller to the Fans.

Connect the ARGB controller to the SATA connector.

ARGB Controller Installation Guide

29 29 29 30

Andere Thermaltake Computerhardware Handbücher

Thermaltake

Thermaltake Floe RC Ultra 360 Bedienungsanleitung

Thermaltake

Thermaltake Divider 370 TG ARGB Bedienungsanleitung

Thermaltake

Thermaltake CL-P0540 Bedienungsanleitung

Thermaltake

Thermaltake Pacific MX2 Plus Bedienungsanleitung

Thermaltake

Thermaltake Riing Silent 12 Sync Bedienungsanleitung

Thermaltake

Thermaltake TH240 ARGB Sync Bedienungsanleitung

Thermaltake

Thermaltake Floe RC240 Bedienungsanleitung

Thermaltake

Thermaltake Floe Riing RGB 240 Bedienungsanleitung

Thermaltake

Thermaltake TH240 ARGB Sync Bedienungsanleitung

Thermaltake

Thermaltake TH360 V2 Ultra ARGB Sync Bedienungsanleitung

Thermaltake

Thermaltake A1827 Bedienungsanleitung

Thermaltake

Thermaltake Pacific A2 Ultra Bedienungsanleitung

Thermaltake

Thermaltake Pacific V-RTX 4090 Plus Bedienungsanleitung

Thermaltake

Thermaltake Pacific CL360 Plus Bedienungsanleitung

Thermaltake

Thermaltake A2016 Bedienungsanleitung

Thermaltake

Thermaltake Water 3.0 Ultimate Bedienungsanleitung

Thermaltake

Thermaltake Pacific W5 Bedienungsanleitung

Thermaltake

Thermaltake Toughpower 850 B Bedienungsanleitung

Thermaltake

Thermaltake FANLESS VGA Bedienungsanleitung

Thermaltake

Thermaltake TH360 ARGB Sync Bedienungsanleitung

Thermaltake

Thermaltake TOUGHLIQUID 240 ARGB Sync Bedienungsanleitung

Thermaltake

Thermaltake V3 Black Edition VL8000 Series Bedienungsanleitung

Thermaltake

Thermaltake CLP0538 Bedienungsanleitung

Thermaltake

Thermaltake TOUGHLIQUID 360 ARGB TRX40 Edition Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung