Thermaltake Toughpower 1500W Bedienungsanleitung

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

~Build for Extreme~

ATX 12V 2.3 & EPS 12V 2.91 Version

www.thermaltake.com [email protected]

E161451

Toughpower

CableManagement 1500W

14cm Fan14cm Fan

230V Edition230V Edition

297X 210 mm

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

Table of contents

1.Introduction 02

2.Product Features

3.Components Check

4.Connectors & Cables

5.Installation Steps

6.+12V Rail Distribution

7.SPEC Table

8.Other Specification

9.Trouble Shooting

10.Contact Us

297X 210 mm

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

1.2 Warnings and Cautions

1.2.1 Do not unplug the AC power cord when the power

supply is in use. Doing so may cause damages to your

components.

1.2.2 Do not place the power supply in a high humidity and

temperature environment.

1.2.3 When usin

power supply under testing conditions where the power

supply unit is not installed in a PC with its components,

please follow the steps below:

1) Please take a paper clip and untwist it.

2) Make sure the power supply unit is in the "OFF"

position.

3) Locate the 20+4 pin motherboard connector from the

power supply unit.

4) Plug one side of the paper clip into the green wire hole.

5) Plug the other side of the paper clip into any of the

black wire holes.

6) Turn on the PSU to see if the power supply fan(s)

turn(s) on.

1.2.4 High voltages exist in the power supply. Do not open the

power supply case unless you are an authorized service

technician or electrician.

1.2.5 All warrantees and guarantees will be voided, if failure

to comply with any of the warnings and cautions

covered in this manual.

g Toughpower Cable Management 1500W

02 03

1. Introduction

We live up to the promise of Thermaltake logo in our unending

quest for excellence. Shall you have any suggestion or

comments, please access our website:

Http://www.thermaltake.com

or e-mail to:

[email protected]

We appreciate your kindly feedback and you will receive the

prompt response from our customer service team.

Please take the time in familiarizing yourself with the power

supply, its connectors and the contents of this manual before

proceeding with the installation of the power unit. You will need

a Philips crosshead screwdriver, perhaps your PC case manual

and most certainly your motherboard manual.

Should you have any questions regarding the content of the

manual, please contact Thermaltake directly. Failure to follow

the proper procedures may cause severe bodily harm or PC

component damage.

1.1 Statement

297X 210 mm

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

04 05

2. Product Features

2.1 Four 8pin & Four 6pin PCI-E Connector

Toughpower 1500W power supply comes with four 8pin and

four 6pin PCI-E connectors. This combination of PCI-E

connectors makes Toughpower 1500W be able to support

NVIDIA SLI & ATI CrossFire technology and multiple high-

end graphic cards.

2.2 Excellent Efficiency (up to 87%)

Toughpower 1500W provides excellent efficiency and hence

reducing energy consumption. That in return reduces

customers electricity bill.

2.3 140mm Ball-Bearing Fan

The 140mm ball bearing fan effectively increases the airflow

inside the PSU and decreases the ambient temperature.

2.4 Extremely Good Voltage Regulation ( 3%)

This feature allows tighter load regulation ( 3%) than other

power supplies ( 5%) and increase system voltage stability.

2.5 MTBF > 120,000 Hours (Highly reliable)

120,000 hours of MTBF (Mean Time between Failures) goes

above and beyond all ATX specifications.

2.6 Four Independent +12V rails

FOUR independent & powerful +12V rails provides stable

voltage output for whole system and graphic cards. The total

combined load can reach 120 A.

2.7 Cable Management

Cable Management enables users to remove unused cables

and significantly improves the airflow in the chassis.

2.8 Industrial Grade Components (capacitor,

transformer, etc)

All components are specially designed for industrial

environment and extreme conditions.

2.9 Hi-Tech Black Coating

With special Hi-Tech Black coating, Toughpower 1500W

PSUs transmit professional, elegant and unique image.

2.10 High +5VSB Output

Built-in higher +5VSB supports up to 12 USB devices. Also,

even the system is power off, USB devices can still be

charged by the 3Asustained output.

297X 210 mm

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

06 07

4mounting screws

3. Components Check

2Three sets of wirew/ 8pin

PCI-E connector

6One AC Input power cord

4Two sets ofwire w/ 4pin

peripheral connector

3Two sets ofwires w/ 5pin

SATA connector

8User manual

5One set of8-pin to 6-pin

PCI-E adapter

One Toughpower1500W power

supply uni t

(W/one 20+4pin mainpower connector,

one 4+4pin +12Vpower connector,one

8pin power connector, and one

8pin/6pin PCI-E connector)

2Three sets of wirew/ 6pin

PCI-E connector

4. Connectors & Cables

4.1 Connectors

4.1.1Main Power Connector (20+4 pin)

Support the latest ATX 12V 2.3 system motherboard

Voltage

+3.3V

GND

+5V

GND

+5V

GND

+5Vsb

+12V1

+3.3 V

Voltage

+3.3 V

-12 V

GND

PS_ON

GND

N/C

+5 V

GND

Color

Orange

Black

Red

Black

Red

Black

Purple

Yellow

Orange

Color

Orange

Blue

Black

Green

Black

N/C

Red

Black

Gray

297X 210 mm

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

08 09

4.1.3 CPU Connector (8 pin)

Support the 8-pin EPS 12V system motherboard

Color Signal Pin

Black

Yellow

GND

Black GND

+12V2

Yellow

+12V2

+12V3

Yellow

4.1.2 CPU Connector (4+4 pin)

Support both dual CPU and single CPU systems by simply

combining (8 pin) or splitting (4 pin X 2) the connectors

Color Signal Pin

Black

Yellow

GND

Black GND

+12V2

Yellow

+12V2

4.1.5 PCI-E Connector (6 pin)

Support the latest high-end graphic cards with 6 pin socket

Color Signal Pin

Yellow +12V3/+12V4 1

Yellow +12V3/+12V4 2

Yellow +12V3/+12V4 3

Black GND 4

Black GND 5

Black GND 6

4.1.4 PCI-E Connector (8 pin)

Support next generation 8 pin sockets on high-end

graphic cards and can support the existing 6 pin sockets

by connecting to the 8 pin to 6 pin converter.

Color Signal Pin

Yellow/Blue

Black

+12V3/+12V4

Black GND

GND

Black

GND

Black

297X 210 mm

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

10 11

4.1.7 Peripheral Connector (4 pin)

Support IDE/SCSI (HDD/CD/DVD..etc) devices

Color Signal Pin

Yellow

Black

Red

+12V1

GND

+5V

4.1.6 SATAConnector (5 pin)

Support the new generation high-speed SATAdevices

Yellow

+12V1

Black

GND

Red

+5V

Black

GND

Orange 3.3V 5

Color Signal Pin

4.1.8 Floppy Disk Connector (4 pin)

Support Floppy Disk and some other additional devices

Color Signal Pin

Red

Black

Black GND

GND

+12V1

Yellow

+5V

4.1.9 8 pin PCI-E to 6 pin PCI-E converter

Enable 8pin PCI-E connector connect to the graphic card

that only has 6pin PCI-E socket.

297X 210 mm

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

12 13

4.2 Cables

Users can optimize the cables arrangement within the chassis

by using only what users need. This feather increases the

airflow and reduces the overall ambient temperature within the

chassis, also improves the overall look and tidiness of the

system.

Embedded Socket and Modularized Cable Management Design:

4.2.1 Inside the box, you will find the following wires and

connectors

PCI-Express

Connector

SATA, Peripheral, and

Floppy Connector

1 x 20+4pin motherboard connector

Modular Cables

2 x quad SATA power connectors

2 x quad 4pin IDE & single floppy power connectors

500mm + 150mm

500mm

500mm+150mm+150mm+150mm

500mm+150mm+150mm+150mm+150mm

Wires & Connectors

Native Cables

1 x 8pin EPS12V connector

500mm

550mm

1 x 4+4pin EPS12V connector

1 x 8pin/6pin PCI-E connector

3 x 6pin PCI-E connector

3 x 8pin PCI-E connector

5. Installation Steps

To prevent electrical shocks, please disconnect the power cord

from your existing power supply unit.

StepStepStep 1

After install the power supply unit into the chassis and then

connect the 20+4 pin main power cable to motherboard 20pin

or 24 pin socket.

StepStepStep 2

Connect the 4+4 pin / 8 pin +12V power connector to

motherboard (User can use either 4-pin or 8-pin to connect

motherboard socket, please check your motherboard user

manual for detail information)

297X 210 mm

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

14 15

StepStepStep 3

Connect the 6pin or 8pin PCI-E connectors to your graphic

card(s) as needed.

StepStepStep 4

Connect the 4 pin power connector to peripheral devices such

as DVD-Burner, hard drive, and etc. In addition, user can

connect the 4-pin floppy power connector to connect the floppy

drive.

If your devices are S-ATA interface, there are also S-ATA

connectors available.

6. +12V Rail Distribution

20+4pin Main Power

4+4pin CPU Power

8 pin CPU Power

Peripheral & Floppy

S-ATA

6 pin standard PCI-E

6 pin Modular PCI-E

8 pin standard PCI-E

8 pin Modular PCI-E

Connector +12V1 +12V2 +12V3 +12V4

W0171 - 1500W PSUW0171 - 1500W PSU

297X 210 mm

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

Toughpower CableManagement 1500W

ATX 12V 2.3 & EPS 12V 2.91 Version

16 17

7. SPEC Table

Model

W0171

SPECIFICATION

Power

Dimension

Switches

PFC

Cooling System

Noise

P. G. Signal

Efficiency

INPUT

Input Voltage

Input Frequency Range

MTBF

Input Current

Hold-up Time

1500W

200mm(L)x150mm(W)x86mm(H)

ATX Logic on-off additional power rocker switch

Active PFC (PF> 0.9)

140mm Fan, 2300RPM 10%

16 dBAat 1300 RPM

100-500 ms

up to 87%

16ms

230 VAC

47 ~ 63 H z

120,000 hrs minimum(at 25 )

10A

OUTPUT

Max/Min Regulation *1

Ripple & Noise Output

+12V1

+12V3

+12V2

+5V

+3.3V

-12V

+5Vsb

Total Power 1500W

20A/1.0A +3,-3% 240mV

750W

9.6W

240mV

100mV

240mV

100mV

+3,-3%

+10,-10%

+3,-5%

40A/1.0A

30A/0.5A

20A/1.0A

40A/1.0A

0.8A/0.0A

3.5A/0.0A

*1. Add 0.1uF and 47uF capacitors across output terminal during ripple & noise test.

ENVIRONMENT

Operating Temp.

Storage Temp.

Operating Humidity

Storage Humidity

10 to 50

-20 to 70

20% to 90%, non-condensing

5% to 95%, non-condensing

PROTECTION

DC rail Trigger Point/Range

Over Voltage Protection

Over Current Protection

Short Protection All output to GND

+3.3V trip point

+5.0V trip point

+12.0V trip point

+3.3V

+5.0V

+12V1 & +12V2 22A ~35A

33A ~50A

15.6 Vmax

4.5 Vmax

7.0 Vmax

Peak Power 1600W

17.5W

+12V4

100mV

+3,-3%30A/0.5A

+12V3 & +12V4

Under Voltage Protection

+3.3V trip point

+5.0V trip point

+12.0V trip point

42A ~60A

2.0 Vmin

3.3 Vmin

8.5 Vmin

8. Other Specification

8.1 Inrush Current:

AC input 230Vac at 25 C cold start power no damage

8.2 Power Efficiency

80%(min.) at full load(typical)

8.3 CE Requirements

8.3.1 Conducted EMI

1. Meet FCC: ClassB

2. Meet CISPR 2 2: ClassB

3. Meet BSM I: ClassB

8.3.2 Safety Standards

1.Meet CUL (U L6095 0 )

2.Meet TUV EN60950

3.Meet CB (IE C 950)

4.Meet CE

8.3.3 Harmonic

Meet IEC1000-3- 2, Class D

297X 210 mm

Andere Handbücher für Toughpower 1500W

Inhaltsverzeichnis

Andere Thermaltake Stromversorgung Handbücher

Thermaltake

Thermaltake Toughpower Grand TPG-850M Bedienungsanleitung

Thermaltake

Thermaltake Toughpower Grand Bedienungsanleitung

Thermaltake

Thermaltake W0104 Toughpower 650 AP Betriebsanleitung

Thermaltake

Thermaltake W0132 Bedienungsanleitung

Thermaltake

Thermaltake TR2 RX 700w Bedienungsanleitung

Thermaltake

Thermaltake W0172 Toughpower 850 AP Bedienungsanleitung

Thermaltake

Thermaltake ATX 12V 2.2 Bedienungsanleitung

Thermaltake

Thermaltake TR2-550W Bedienungsanleitung

Thermaltake

Thermaltake TR2 Bedienungsanleitung

Thermaltake

Thermaltake TWV 500W Bedienungsanleitung

Thermaltake

Thermaltake SMART 700W Bedienungsanleitung

Thermaltake

Thermaltake W0163 Toughpower QFan 650 A Bedienungsanleitung

Thermaltake

Thermaltake Purepower W0328 Bedienungsanleitung

Thermaltake

Thermaltake TOUGHPOWER PF3 1200W Bedienungsanleitung

Thermaltake

Thermaltake W0156 Bedienungsanleitung

Thermaltake

Thermaltake W0151 Bedienungsanleitung

Thermaltake

Thermaltake TR2-430W Bedienungsanleitung

Thermaltake

Thermaltake Toughpower Grand Bedienungsanleitung

Thermaltake

Thermaltake W0158 Bedienungsanleitung

Thermaltake

Thermaltake Toughpower 800W Bedienungsanleitung

Thermaltake

Thermaltake LITEPOWER PRO 550W Bedienungsanleitung

Thermaltake

Thermaltake TR2 RX 700w Bedienungsanleitung

Thermaltake

Thermaltake W0157 Bedienungsanleitung

Thermaltake

Thermaltake Litepower 400W Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung