Thomas&Betts Steel City 54151CFB-BHL Bedienungsanleitung

Individual Cat. No

54151CFB-BHL...............

New Work Bar Hanger with 1-1/2" Deep Box. (Metallic Ceiling Fan Box)

WARNING

DISCONNECT THE ELECTRICAL CIRCUIT SUPPLYING POWER

TO THE OUTLET PRIOR TO INSTALLATION.

CAUTION

TO PREVENT INJURY, THE HANGER MUST BE SECURELY

INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS

BEFORE MOUNTING OR CONNECTING A CEILING FAN OR

LIGHT FIXTURE.

AFTER INSTALLATION OF THE HANGER, BE SURE TO

FOLLOW ALL MOUNTING INSTRUCTIONS WITH THE CEILING

FAN OR LIGHT FIXTURES.

READ ALL INSTRUCTIONS AND WARNINGS CAREFULLY BEFORE PROCEEDING!

INSTALLATION INSTRUCTIONS:

TA04763 D Page 1 of 2

NEW WORK CEILING FAN

AND LIGHT FIXTURE BAR HANGER

INSTRUCTION SHEET

Figure 1

1. Expand the bar hanger to the length of spacing between the wood

ceiling joists. If the drywall is 1/2" thick, the locating tabs on the

end-plates can be used to position the hanger. If the drywall is

thicker than 1/2", the locating tabs need to be broken off and the

end plate is positioned to make the bottom of box ush with

drywall. (See Figure 1).

END-PLATE

Reference drywall ush with bottom of box.

LOCATING

TAB

—CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY QUESTIONS. —

IMPORTANT SAFETY NOTICE: USE ONLY METALLIC BOX AND SCREWS PROVIDED IN KIT. DO NOT SUBSTITUTE!

CAUTION

O NOT EXCEED MAXIMUM WEIGHT RATINGS

FOR 16” SPANS

MAX LIGHT FIXTURE = 200 LBS.

MAX CEILING FAN = 70 LBS.

FOR 24” SPANS

MAX LIGHT FIXTURE = 90 LBS.

MAX CEILING FAN = 70 LBS.

INSTALL THIS BAR HANGER SUPPORT ONLY IN

ACCORDANCE WITH APPLICABLE NATIONAL AND LOCAL

BUILDING AND ELECTRICAL CODES.

2. Use a hammer to strike the engaging spurs into the wood ceiling joist. This will provide temporary support for

the hanger.

3. Using the holes in the end plates of the hanger as a template, drill (4) 7/64˝ diameter pilot holes 3/8˝ deep

(MAX.). Use the wood screws provided and install securely through holes of the end plates. (See Figure 2).

4. Align and fasten the box support bracket along the hanger where the outlet box is to be mounted on the hanger.

5. Attach the ceiling fan box by aligning the two holes on either side of the bottom center knockout with the two

holes in the box support bracket.

•Drive the provided #10-32 x 5/8" fan mounting screws with lockwashers into each of the two holes through

the box fastener (See Figure 2).

IMPORTANT SAFETY NOTICE: MOUNTING OF METALLIC AND NON-METALLIC CEILING FAN BOXES REQUIRES DIFFERENT

SCREWS. IF INCORRECT SCREWS ARE USED, THE BOX MAY DISLODGE FROM THE HANGER ASSEMBLY. ONLY USE #10-32 x 5/8"

SCREWS WITH LOCKWASHERS FOR STEEL CITY METALLIC CEILING FAN BOXES. ONLY USE #10-32 x 5/8" SCREWS WITHOUT

LOCKWASHERS FOR UNION®NON-METALLIC CEILING FAN BOXES. DO NOT INTERCHANGE SCREWS.

INSTALLATION INSTRUCTIONS - continued

WARNING

DO NOT USE THE SPURS AS SOLE MEANS OF SUPPORT FOR THE HANGER.

WARNING

THE BOX SUPPORT BRACKET MUST BE POSITIONED WITHIN THE OVERLAP

OF THE TWO CHANNELS (SEE FIGURE 2).

Thomas & Betts Corporation

Memphis, Tennessee

www.tnb.com

WARRANTY: Thomas & Betts sells this product with the understanding that the user will perform all necessary tests to determine the suitability of this product for the user's intended application.

Limitations and Exclusions: THE ABOVE WARRANTY IS THE SOLE WARRANTY CONCERNING THIS PRODUCT, AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED,

INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE SPECIFICALLY DISCLAIMED. LIABILITY