THOMSON 14MG10U Bedienungsanleitung

User

manual

User

manual

User

manual

14MG10U

Mains connection and remote batteries

Mains connection

The TV is suitable for use on a.c. mains supply, 220-240V, 50 Hz only.

It must not be connected to d. c. mains.

The mainsleadoftheTVisfitted witha moulded plug.Ifthemains

sockets are not compatible or if for any reason the plug is

removed please follow these directions:

The moulded plug cannot be rewired and if removed must be disposed of safely.

DO NOT under any circumstances plug the severed plug into any mains socket as this could

result in electric shock.

IMPORTANT:Iftheplug is removed rewirenew plugas follows:The wires in themains plugare

coloured in accordance with the following code: BLUE - NEUTRAL / BROWN - LIVE.

As the colours of the wires in the mains lead of this apparatus may not correspond with the

coloured markings identifying the terminals in your plug, proceed as follows:

- BLUE wire to the terminal coded N (Neutral) or coloured black.

- BROWN wire to the terminal coded L (Live) or coloured red.

DO NOT make any connection to the terminalin the plug which is marked by the letterE orby

the safety earth symbol or coloured green or green and yellow.

Afusedplugmustbefittedwitha5AfuseapprovedbyASTAorBSItoBS1362andfusecovers

must always be securely replaced.

Remote control batteries

The remote control requires two batteries size AA as supplied with the unit.

Unclip the cover at the rear and insert the batteries the correct way round as

shown. The ends are usually market + and -.

Replace the batteries when the unit no longer operates at normal viewing distances.

When replacing batteriesdo notmix oldand new -donot mix makes andtypes.

alkaline types are recommended forlong life.Never risk damage to theremote

control by extreme heat - do not leave close to a radiator or on a window ledge

in direct sunshine.

Connections

220- 240V ~50Hz

1. Aerial Socket

Enables connection of the aerial and, if required, a video recorder (see manual for latter).

To tune the channel reserved for your video recorder, start up the recorder then carry out

MANUAL CHANNEL SETTING operations.

Store at any programme ending with a 9 (9,19,29, etc.)

Each time you use the video recorder, switch to the channel assigned to it.

2. SCART Socket

This is used to connect:

– a VHS, 8 MM, S–VHS or Hi–8 video recorder or camcorder,

– a PAY TV decoder,

– a video games console.

To use the connected device, select the audiovisual programme by pressing the button.

This selection is automatic for some devices.

AV is displayed at the bottom of the screen.

IfyouhaveanS-VIDEOdevice,pressthe button again. S-VIDEO is then displayed at the bottom

of the screen for a few seconds.

When you switch off the device and if you have not changed channel during play, the TV set

automatically returns to the previous channel.

If the TV set has been switched on by the video recorder, it will be placed on stand–by when the

video recorder is switched off.

Batteries: Remove the lid at the back of the remote control and insert two 1.5

V, LR06 batteries.

Display programme No.

and sleep timer (Yellow

button)

Display Timer Menu

(Green button)

Call up personal

adjustments

(Red button)

Confirmanactionor

validate a menu

option

To switch to connected

equipment (e.g.: video recorder)

Toleaveamenu

Sound mute

Volume level

Stand-by

Inactive

Adjustment: move to

Right/Left in menus and

select one of the proposed

options

Move Up and Down in

the menus

To go to Picture and

Channel Adjustment

menus

Direct access to

programmes and entering

numerical values in

menus

To change programme

”Please respect the environment! Before throwing any batteries away, consult

your distributor who may be able to take them back for specific recycling..”

Remote Control

AUTO INSTALL.

PR01

AUTO INSTALL.

Automatic Channel Setting

This set is equipped with an automatic search system which will search for and store all

channels available in your region. To help identify the programmes, we suggest that you have to

hand a TV guide or daily newspaper.

Ensure that the aerial lead is connected to the TV set.

Check that any equipment connected only via the aerial (video recorder or satellite equipment) is

operating.

Switch off any equipment connected via the SCART socket.

Installation

Press the ON/OFF button, the indicator lamp lights up.

If the television set remains on stand–by, press one of

the buttons on the remote control numerical keypad.

When the television set is turned on for the first time, the

Installation menu appears automatically.

If this is not the case, you can call it up by:

– pressing the button on the remote control three

times.

Press to confirm.

A new menu appears. Automatic search begins. The cur-

sor moves from left to right on the VL line, then on the VH

line and then on the U line. The channels found are stored

in memory in order starting from programme PR 01.

You can stop the automatic search at any time by pressing

the button.

The search stops automatically at the end of the U band

or when 99 channels have been found.

The Programme Organizer menu then appears automatically.

The channel stored on programme PR 01 is selected (see next page).

PR01

AUTO INSTALL.

Changing a Programme Number

Select the channel number to be changed using the

button.

Using the numerical keypad on the remote control, enter the

new programme number.

You can also use the buttons on the remote control.

Press the button to confirm the change.

The programmes stored under the old and new numbers are then swapped.

Repeat this operation to change other programme numbers.

Erasing a Programme

Select the programme to be erased using the button.

Enter 0 or 00 on the numerical keypad of the remote control.

Press to confirm. The programme is erased.

Check that all the programmes are in the required order using the button, then press

to leave the menu.

Manual Channel Setting

Press the button twice to call up the channel setting menu.

1. Channel Search

Select the 2nd line of the menu using the button.

Start the search by pressing:

– the button for a forward search,

– the button for a backward search.

The search fully covers the VL, VH and U bands starting

from the channel on the screen. The cursor moves and

as soon as a channel is found, the picture appears on

the screen.

Wait for the menu to go to the bottom of the screen for optimum reception.

If the picture corresponds to the channel required, go to the 4th line (PR), otherwise

continue the search.

If you wish to stop the automatic search, press the button.

2. Programme Number and Storing in Memory

Select the 4th line of the menu using the button.

If fine tuning is necessary, see Fine Tuning

Enter a programme number using the numerical buttons of the

remote control.

You can also use the

buttons

Store the programme number you have allocated to the channel by pressing the button.

The 2nd line of the menu is then selected again.

Restart the search using

the buttons

3. Fine Tuning

Only necessary in the event of interference

If fine tuning is necessary, select the 3rd line of the menu

using the button.

If necessary, adjust the picture using the buttons.

Select the 4th line (PR)usingthe button to allocate a programme number to the channel

and store it in memory (see Programme Number and Storing in Memory)

If a channel has required fine tuning, it will be stored in memory with the AFC (Automatic

Frequency Control) deactivated.

Press the button to leave the menu.

Picture Adjustments

Press the button to call up the Picture Menu.

===

=SHARPNESSCONTRASTCOLOURBRIGHTNESS TINT

Select the function to be adjusted using the buttons.

The tint function is only active in NTSC mode.

Adjust as required using the buttons.

Storing Personal Adjustments

You can store the adjustments you have just made and call

them up at a later stage. Caution: these personal adjustments

will replace and delete the standard settings made at the

factory.

With the Picture Menu displayed, press the red button.

Press the button to leave the menu.

Sleep Timer

Press the green button to call up the Stand–by

Menu.

Set the stand–by time in 10–minute steps (up to 4 hours) using

the buttons

Press the button to leave the menu

The television set is child locked when the programmed time

period has elapsed. The stand–by indicator will flash (see Day to

Day Operation).

To cancel the sleep time function:

–pressthegreen button to call up the menu.

–pressthe button once or several times to return to: –:––

When the display indicates –:––, the sleep timer function is deactivated.

The sleep timer function is also deactivated when the television set is switched to stand–by from

themainON/OFFswitch.

The television is then child locked and the stand–by indicator flashes (see Day to Day

Operation).

Inhaltsverzeichnis

Andere THOMSON Röhrenfernseher Handbücher

THOMSON

THOMSON 72DF89L Bedienungsanleitung

THOMSON

THOMSON SABA M5115GT Bedienungsanleitung

THOMSON

THOMSON Spectra SC 63 TH Bedienungsanleitung

THOMSON

THOMSON 21MS76CT Bedienungsanleitung

THOMSON

THOMSON 2 0 D G 7 6 C Bedienungsanleitung

THOMSON

THOMSON 32VT68NV Bedienungsanleitung

THOMSON

THOMSON 32VT68NV Bedienungsanleitung

THOMSON

THOMSON 20DG76CT Bedienungsanleitung

THOMSON

THOMSON M8521E Bedienungsanleitung

THOMSON

THOMSON 1 4 M S 1 5 F T Bedienungsanleitung

THOMSON

THOMSON 2 0 M F 1 5 G T Bedienungsanleitung

THOMSON

THOMSON 14MG10F Bedienungsanleitung

THOMSON

THOMSON 29DU78NV Bedienungsanleitung

THOMSON

THOMSON 29DL25UD Bedienungsanleitung

THOMSON

THOMSON 29DU78NV Bedienungsanleitung

THOMSON

THOMSON 25DH55N Bedienungsanleitung

THOMSON

THOMSON 2 5 D G 1 6 E T Bedienungsanleitung

THOMSON

THOMSON TX807C Bedienungsanleitung

THOMSON

THOMSON 21 MS 77 CX Bedienungsanleitung

THOMSON

THOMSON 2 4 W K 2 3 U Bedienungsanleitung

THOMSON

THOMSON 15LB020S4 Bedienungsanleitung

THOMSON

THOMSON 14MS15GT Bedienungsanleitung

THOMSON

THOMSON 29DU78NE Bedienungsanleitung

THOMSON

THOMSON 14MG76C Bedienungsanleitung

Beliebte Röhrenfernseher Handbücher anderer Marken

JVC

JVC AV-21QS5SP Bedienungsanleitung

Philips

Philips COLOR TV 25 INCH TABLE TR2517C Bedienungsanleitung

Hitachi

Hitachi 27CX01B Bedienungsanleitung

LG 30FZ1DC Bedienungsanleitung

Sony

Sony FD TRINITON WEGA KV-24FS120 Bedienungsanleitung

RCA

RCA F19442 Bedienungsanleitung

Samsung

Samsung CS761 Bedienungsanleitung

Philips

Philips 29PT4973 Bedienungsanleitung

Panasonic

Panasonic TC-29P100 Series Bedienungsanleitung

RCA

RCA F19422 Bedienungsanleitung

Sony

Sony WEGA KV 32HS20 Bedienungsanleitung

Samsung

Samsung SlimFit TX R3079WH Bedienungsanleitung

Palsonic

Palsonic MODEL 5179G Bedienungsanleitung

Toshiba

Toshiba CF13H22 Bedienungsanleitung

Magnavox

Magnavox MS3650C - 36" Smart Ctv Handbuch

Toshiba

Toshiba 14AF41 Bedienungsanleitung

Philips

Philips 21PT9469 Bedienungsanleitung

Mitsubishi

Mitsubishi CS-35305 Bedienungsanleitung