THOMSON VS 650 Bedienungsanleitung
1
Wireless video transmitter
Precautions
• Safety
This equipment contains heat sensitive components. Maximum ambient
temperature must not exceed 35° Celsius.
Humidity in rooms where this equipment is situated must not exceed a hygrometric
level of 85 %. If you have to use your equipment outside, avoid exposing it to rain
water or to splashes. The transition from a cold environment to a hot one may cause
condensation. Allow it to dry by itself before re-starting the equipment.
In the event of prolonged absence, switch off the equipment by means of the on/off
switch. Even when switched off, certain components remain live. In order to insulate
it completely you must remove the plug from the main electricity supply.
In the event of an electrical storm, it is advisable to disconnect the equipment from
the electricity supply so as to avoid potentially damaging electrical or
electromagnetic surges. To this end, make sure that the mains plug is easily
accessible for disconnection.
Disconnect the equipment immediately if you detect a smell of burning or smoke.
Under no circumstances must you open the equipment yourself; you run the risk of
electrocution.
• Maintenance
Clean the equipment with a soft cloth and a neutral detergent. The use of solvents,
abrasive products or alcohol-based products is likely to damage the equipment.
• Regulations
This equipment must only be installed inside. Its use is restricted to private radio
transmission. Connection to a public or independent network, or to an outside aerial
is prohibited.
Under no circumstances should this appliance be put to industrial use. It is designed
solely for domestic operation.
THOMSON multimedia disclaims all responsibility in the event of use that does not comply
with the present instructions.
EN
VS650 22/02/02 16:36 Page 1
2
LIVING ROOM BEDROOM
Transmitter
Video recorder,
satellite receiver,...
Receiver
Remote control
for video recorder,
satellite receiver,…or
universal remote control.
Principles of operation
Technical characteristics
Power supply: 12V DC
VS 650 : 4 channels (A : 2.411 GHz - B : 2.434 GHz - C : 2.454 GHz - D : 2.473 GHz)
VS 650 U : 4 channels (A : 2.411 GHz - B : 2.434 GHz - C : 2.454 GHz - D : 2.473 GHz)
VS 650 E : 3 channels (A : 2.421 GHz - B : 2.449 GHz - C : 2.477 GHz)
Remote control return: 433,92 MHz
Transmitter power: 10 mW
VS650 22/02/02 16:36 Page 2
3
The Video Sender VS 650 permits the relay of an Audio-Video signal from your
main set-up to a second television set located in another room and equipped with a
scart connection (or RCA/Cinch). The main set-up is the place in which you have
chosen to install the majority of your equipment (television set, video recorder,
satellite receiver, DVD player,..) you can operate the units from the room with the
second television set by using their remote controls, or with a universal remote
control.
You can play and hear music if you connect the transmitter to a suitable outlet
(AUDIO OUT), and the receiver to an amplifier (AUDIO IN) placed in another room.
In that case, you will need to get a SCART/Cinch adapter (not supplied).
What is this equipment for?
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
STANDBY
SOURCE
AUTO
ADJUST
PCCARD
ACCESS
DVD player
Television set
Video recorder
Camcorder
Video disc player
Satellite/Cable receiver
and decoder
Video projector
A/V Amplifier
EN
VS650 22/02/02 16:36 Page 3
4
The connection setup depends on the devices you have. Here is an example of how
to connect the transmitter in a setup comprising a television set and another device
(DVD player).
Follow the instructions below and the diagram opposite.
Also refer to the operating diagram printed on the inside cover of this manual.
1. Place the transmitter (1) near the device (video recorder, DVD player, etc.) from
which you wish to transmit pictures and sound and connect it using the mini DIN
cord and extension box (2Aand 2 B). Connect the SCART cable (2 C) to socket 1
of the extension box.
With a SCART cable (not supplied), connect the TV set to the extension box
(socket 2) already connected to the video recorder or DVD player.
The red light on the extension box indicates that the transmitter is turned on.
2. Carefully extend the antenna of the transmitter (1) and orient it towards the room
where your second TV set (TV2) is located. Turn on (position ON) the transmitter
and receiver, using the ON/OFF switch located on its lower side. Place the
channel selectors of the transmitter and the receiver on the same channel (same
letter).
3. Fit the lead (4) following these stages:
- connect the jack plug to the IR EXTEND socket,
- unwind the lead and place one cell near the infrared window of the unit to be
operated (video recorder or other),
- after installing the receiver (see Pages 6 and 7), ask someone to use the remote
control of that equipment item to be controlled from the room where the second
(TV2) is located,
- by moving the cell around in front of the unit to be operated you will find the
location that permits its control from the other room. You must fix the cell in that
position. Usually, this will be a more or less large, transparent area located on the
front of the unit.
4. Remove the protective self-adhesive film from the infrared cell of cord (4) and affix
it to the infrared-sensitive panel of the equipment to be remote controlled. The
cordon has 3 cells in order to let you play video and audio from 3 equipment items
connected to the (TV1) set (see Diagram on Page 10).
5. Fit the mains supply lead (3) to the transmitter and plug it into a 220/240 V ~ 50 Hz
mains power supply.
Installation of transmitter
VS650 22/02/02 16:36 Page 4
5
DC 12V IR EXTEND
DC12V VIDEOIN IR EXTEND
2
1 3
4
220/240V ~ 50 Hz
VS 650 U
VS 650
VS 650 E
TV1
TV2
AB C
EN
1
2
VS650 22/02/02 16:36 Page 5
6
Receiver
Receiver
AUDIO OUT
L R DC 12VVIDEO OUT
6
TV2
5 7
1. Place the receiver (5) on, or near, the second television set.
2. Connect the receiver (5) to the second television set using the lead (6) following
the same instructions as for the transmitter.
3. Extend the antenna on the receiver (5) and orient it toward the main TV set (TV1).
4. Raise and extend the telescopic aerial of the receiver (5).
5. Fit the mains supply lead (7) to the receiver and plug it into a 220/240 V ~ 50 Hz
mains power supply.
! THE ANTENNA allows you to transmit and receive audio and video signals over a
maximum range of 30 meters in free air environments. Inside a typical lodgment the range
will be less because of signal attenuation by building material absorption.
! THE TELESCOPIC AERIAL permits the control of the unit whose pictures you wish to
see in the room containing the second television set (TV2).
! THE POWER SUPPLY plug fitted to the transmitter (1) is not the same as the one fitted
to the receiver (7).
Installation of receiver
220/240V ~ 50 Hz
VS 650 U
VS 650
VS 650 E
VS650 22/02/02 16:36 Page 6
7
1. Switch on the transmitter (1) and the receiver (5) by switching their ON/OFF
buttons to the ON position.
2. Make sure that the transmitter and the receiver are set to the same
channel by checking the position of the selectors located under the
casing. They must be set to the same channel (same letter).
3. Switch on your equipment (television sets, video recorders ...) in both rooms.
4. Using the remote control of the unit whose pictures you wish to see, and from the
room containing the second television set (TV2), select the channels or video
functions (or others) according to the unit you are controlling.
Special operating details:
No picture on TV2? If you fail to obtain the desired picture on the second television
set TV2, select the AV socket, to which the receiver (5) is connected, using the
television’s remote control.
Using a decoder (in France: Canal +, TPS, etc.) on your TV2? To have clear
images on your second TV set (TV2), output from the decoder must pass through a
VCR player, placed in (AV2) mode or set to the channel number assigned for the
encrypted TV channel.
Use of a monitor? If your second television set does not have a connection for an
outside aerial (terrestrial reception), or if it is a monitor, you will be able to see the
channels in the room containing the second television set by selecting those of the video
recorder with its remote control.
The picture is scrambled? The running of certain equipment (micro-wave ovens,
digital telephone DECT, un-shielded acoustic loudspeakers, etc ...) may interfere with
signal transmission. Ensure that they are kept away from the transmitter and the
receiver or switch them off.
Make sure that you point the
remote control directly at the
receiver’s (5) infrared window.
Receiver
Instructions for use
EN
VS650 22/02/02 16:36 Page 7
8
You will obtain optimal service operation of your Video Sender by correctly
orienting the antennae (A). However, reflected signals or other signal degrading
factors can affect good quality signal transmission. In this case, readjust antennae
positions or slightly move the transmitter or receiver until you get crystal clear
reception.
DC 12V
ON OFF
VIDEO IN IR EXTEND
ONOFF
off
on
If no picture is obtained,
check that the transmitter and the receiver have not been installed in the reverse
order (each unit corresponds either to the input or to the output of the Audio-Video
signal). Check that they have been properly connected and that they are switched on
(ON position). Ensure that the channel selector is set to the same letter on both units.
If transmission is blurred or scrambled,
choose another channel but make sure that it is identical on both units.
....
a.b.c.d.
Transmitter Receiver
Transmitter
(A)
Receiver
Improvement of picture and sound
(A)
1/2
AUDIOOUT
LRDC12V
VIDEOOUT
....
d.c.b.a.
VS650 22/02/02 16:36 Page 8
9
If your main setup comprises several devices (video recorder, satellite receiver /decoder,
DVD player, etc.) from which you want to transmit pictures and sound to another TV set,
connect them according to the diagram (transmitter side) shown on page 10. In general,
the devices are connected in series.
Connect the devices you use the most (Group 1) to socket 1of the extension box (2A). This
is the default live socket for transmission to the second TV set.
Operation
In addition to the instructions given on pages 7 and 8, it is essential that you switch off all
unused equipment (put them on standby).
For group 2 equipment, you have to use socket 2of the extension box from the receiver
(by pressing button 1/2) or by pressing one of the keys on the remote control of one the
units (in this case the VCR or DVD player) for more than 8 seconds. The remote control
must be aimed at the infrared window on the receiver.
Some remote control units may not be able to perform this function. In that case, use key
1/2 on the receiver.
!
As a general rule, remember to switch off units not in use. Also, refer to the manufacturers’
instructions to see if there are any particularities regarding connection or use. Certain units
may need to have their input scart connection “programmed”.
! In all cases the transmitter must be connected to a scart connection that produces an Audio-
Video signal Out. Refer to the manufacturer’s instructions for confirmation of this.
! These diagrams show a few connection possibilities whose operation depends on
the devices you have, their sockets and the signals they deliver. There are therefore
other connection setups that you may need to try if the setup shown does not meet
your requirements. In that case, ask your reseller for assistance or contact our
customer service (Helpline).
Relay of pictures from several units
You can contact THOMSON by dialing: 0845 601 3093
(For Great-Britain, all calls will be charged at local rate)
www.thomson-europe.com
EN
VS650 22/02/02 16:36 Page 9
10 VS 650-650U-650E/EN/IC-RST/02-02
General information on connections...
GROUP 1
GROUP 2
TV1
DVD
VCR
TV
TV
1
2
AUX
Satellite/Cable Receiver/Decoder
(Canal+, Canal Sat,TPS, Premiere,Telepiu,Via Digital…)
Transmitter
Extension
box
Pictures you will be able to see on
TV1 TV2
VCR or SAT DVD VCR or SAT DVD
Recording
through a video recorder
of the unit marked with an X
Unit on
Video Recorder
Satellite Decoder
or
Satellite Demodulator
DVD Player
✗ ✗ ✗ ✗
✗ ✗ ✗
✗ ✗
✗
✗✗✗ ✗
✗ ✗
✗
✗✗
✗
Only one device per group is available for the transmission and/or viewing of the pictures on TV1 or TV2.
To view/record the pictures transmitted by a DVD player, the other connected devices must support and
retransmit RGB signals on their SCART sockets.
VS650 22/02/02 16:36 Page 10
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Sprachen:
Andere THOMSON Sender Handbücher
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
