Thorsis Technologies IsCAN USB Bedienungsanleitung

isCAN USB

User Manual

isCAN USB

Content

I Certicate of conformity ...................................................................1

1 isCAN USB..............................................................................................2

2 Installation and commissioning....................................................3

2.1 Installation of the driver software..........................................3

2.2 Installation of the Hardware.....................................................4

2.3 Conguration and Commissioning .......................................5

2.3.1 Add a device............................................................................6

2.3.2 Empty-Slot................................................................................7

2.3.3 Removal of a device..............................................................8

2.4 Test Software..................................................................................8

isCAN USB

I Certicate of conformity

according to EC Directive 2014/30/EU (electromagnetic compatibility) of February 26th, 2014.

We hereby declare, that the device indicated below in its design and construction, is in conformity with the essential

safety and health requirements of the EC Directive 2014/30/EU. Changes or modications not approved by Thorsis

Technologies void the validity of the declaration.

Manufacturer: Thorsis Technologies GmbH

Oststr. 18

39114 Magdeburg

Germany

Product designation:

Device type: isCAN USB

Order number: 11300 - 0201

Standards used:

EN 61326-1:2013

Magdeburg, 2017-06-26 Dipl.-Ing. Thorsten Szczepanski, Managing director

isCAN USB

1 isCAN USB

The CAN dongle isCAN USB with the universal USB interface grants a fast ac-

cess to any CAN/CANopen based network. The isCAN USB interface standard

type supports the CAN specication 2.0A (11 bit ID) and 2.0B (29 bit ID). It is

connected with a 9 pin D-Sub connector according to the CiA specication DS-

102. LED‘s indicate the actual working condition. The opto-isolated interface

supports a transmission speed of up to 1 MBit/s.

Technical Data

Interface USB

Controller CY7C68014A, Asic SJA1000

Identier length 11/29 Bit

Transmission rate 10 kbit/s – 1 Mbit/s (CAN)

CE-Certicate isCAN USB

Driver software Windows XP, Vista, 7, 8, 10

Delivery content Hardware, Driver-, Conguration- and Testsoftware;

Documentation german and english on CD

Available software isCAN/CANopen Comm DTM,

isCAN/CANopen Server (OPC),

RP1210 interface Dll with J1939 support,

API interface Dll with examples in C/C++ and C# source code

isCAN USB

2 Installation and commissioning

2.1 Installation of the driver software

The driver software must be installed before connecting the device. Otherwise, the operating system can not nd

the interface to the associated driver.

The driver software package isCAN Multidriver contains a Dynamic Link Library (DLL) which allows the access to the

rmware under the operating systems Windows XP, Vista and Windows 7, 8, 10. The actual operating system is detec-

ted automatically by the driver DLL.

The conguration of the interface can be done with the conguration software isCAN Driver Congurator which

is installed into the Thorsis directory of the Start Menu.

Installation process:

Insert the installation CD-ROM.

The setup starts with an autoroutine; proceed according to the instructions displayed on the screen.

Should Autorun be disabled on your machine, run the setup.exe on the installation CD.

The installation is done in the standard program directory of the target machine under

C:\Program Files\Thorsis\isCAN Multidriver\

isCAN USB

2.2 Installation of the Hardware

The Interface can be connected to the CAN/CANopen network with its D-Sub 9 pin connector directly. With the

integrated USB cable the interface can be connected with the PC/notebook.

Two LEDs indicate the actual operation mode. The green LED indicates that the CAN controller is powered up and

running. It is switched on as soon as a software application initializes the adapter and starts communication on the

CAN bus. The red LED indicates an error condition on the CAN bus by ashing three times.

isCAN USB

To ease the task of hardware conguration the con-

guration software isCAN Driver Congurator is provi-

ded. It is installed in the Start Menu. This simple dialog

based program allows the easy addition and removal

of the CAN interfaces. It also checks the available

resources of the system. Each device is assigned to a

certain number which enables the software to address

the device. Empty devices can be included in order to

allow gaps in the enumeration of devices.

While the conguration software is running the device

drivers of the hardware are stopped. All applications

requiring access to the devices should be terminated

before the start of the conguration software. After the

termination of the conguration software the device

drivers are started again. The new parameters are

available at once for all PCI and USB interfaces.

2.3 Conguration and Commissioning

isCAN USB

Please press the button , choose the device

type you would like to add. Press OK, then make your

settings.

Every isCAN USB adapter is identied by a serial num-

ber. This number ensures that the software is commu-

nicating with the correct hardware in case that there

are more adapters attached to the PC simultaneously.

The number is printed on a label located at the bottom

of the isCAN USB device. Enter the serial number and

conrm the settings by clicking OK. The conguration

software can also detect the serial number automati-

cally by searching for all isCAN USB devices attached to

the PC.

2.3.1 Add a device

isCAN USB

The empty device does not contain any resources. It

serves as a substitute for device numbers not assig-

ned. Using this devices enables a free enumeration of

devices by inserting empty devices between the real

ones.

2.3.2 Empty-Slot

isCAN USB

Mark the device you wish to remove and press the button .

You can then remove the device from the USB port.

The correct operation of isCAN interfaces which have

been added with the isCAN Driver Congurator can be

checked with the help of the test program isCAN Test.

It is installed in the Thorsis folder of the Start Menu.

The following functions are provided by the application:

Choice of congured interfaces (isCAN USB,

isCAN PCI)

Baudrate settings

Transmisson of messages

Display of received messages

2.3.3 Removal of a device

2.4 Test Software

Andere Handbücher für isCAN USB

Inhaltsverzeichnis

Andere Thorsis Technologies USB-Schnittstelle Handbücher

Thorsis Technologies

Thorsis Technologies isPro USBx12 Bedienungsanleitung

Thorsis Technologies

Thorsis Technologies isHRT USB Bedienungsanleitung

Thorsis Technologies

Thorsis Technologies isDNet USB Bedienungsanleitung

Beliebte USB-Schnittstelle Handbücher anderer Marken

PASCO

PASCO SCIENCEWORKSHOP 750 Bedienungsanleitung

Phonic

Phonic FIREFLY 302 USB Bedienungsanleitung

OHAUS

OHAUS Scout STX Series Bedienungsanleitung

Denon

Denon DN-HC4500 - DJ Mixer USB Controller Bedienungsanleitung

Lutron Electronics

Lutron Electronics Stanza SZ-CI-USB-CPN5138 Bedienungsanleitung

Paradox

Paradox PMC5-TI00 Bedienungsanleitung

System Sensor

System Sensor M200WC-RF Leitfaden

Philips

Philips PDIUSBD12 Bedienungsanleitung

KNX

KNX Module IC-USB-S.1 Bedienungsanleitung

Velleman

Velleman KSR10/USB Bedienungsanleitung

NIEUWKOOP

NIEUWKOOP RG7100 Installationsanleitung

Alldaq

Alldaq ADQ-USB 2.0-ISO Bedienungsanleitung

microHAM

microHAM DigiKeyer Bedienungsanleitung

Apogee

Apogee Jam X Bedienungsanleitung

RigExpert

RigExpert TI-3000 Bedienungsanleitung

microHAM

microHAM USB Interface II Bedienungsanleitung

Yamaha

Yamaha i-UX1 Bedienungsanleitung

Mastervolt

Mastervolt USB Interface for Solar ChargeMaster Bedienungsanleitung

Thorsis Technologies isCAN USB Bedienungsanleitung

Beliebte USB-Schnittstelle Handbücher anderer Marken