Thrane&Thrane Explorer 300 Bedienungsanleitung

EXPLORER®300

GETTING STARTED

Congratulations on the purchase of your EXPLORER 300.

Before you start, please check that the following items are present:

• EXPLORER 300 terminal with built-in antenna

• Battery

• AC/DC adapter

• LAN cable

• Getting Started kit including Quick Guide, electronic manual, etc.

1Insert the SIM card (provided by your Airtime Provider)

a. Insert the SIM card into the SIM slot and press

gently until it locks.

b. Slide the lock to secure the SIM card.

2Insert the battery

Insert the battery and press gently until it locks.

NOTE: You can use the battery as power source, or

connect the DC input to one of the following power

sources:

• 100-240 V Mains using the AC/DC adapter

• 12 V DC in a car using the car charger cable

available from Thrane & Thrane

For further information, refer to the User Manual.

3Connect the cables

Connect the cables to the relevant

connectors on the EXPLORER 300.

The connector panel is located on the side

of the EXPLORER 300.

One connector, the Bluetooth phone charging connector marked DC OUT, is

placed at the back of the EXPLORER 300.

4Switch on the EXPLORER®300

Push the power button next to the display and hold it for 1-2 seconds until

the green power indicator lights up.

5Enter the PIN

a. When you are asked for a PIN, press OK.

b. Press or a number of times until the

ﬁrst digit is correct.

c. Press OK to go to the next digit.

The previous digit is indicated by a *.

d. After pressing OK to enter the last digit, press OK again to apply the PIN.

e. If you want to turn off the pointing sound, press or .

6Point the antenna

Important! To obtain optimum bandwidth and operating time, adjust the

position of the antenna with great precision. Do not adjust the antenna

position until all cables are connected and the PIN entered.

Power

Phone LAN

a. Using the built-in compass of the EXPLORER 300 as reference, rotate

and tilt the antenna so that it points in the approximate direction of the

BGAN satellite.

b. Use the displayed signal strength and the pointing sound to ﬁnd the

highest possible signal strength, while slowly rotating and tilting the

EXPLORER 300.

c. Press OK when you have obtained

the highest possible signal strength.

The EXPLORER 300 now starts to establish a connection to the BGAN

network.

The display shows the progress as follows:

• SEARCHING: The EXPLORER 300 searches for the network operator.

Note that the search procedure can be very short, so you may not see

this text.

•

REGISTERING: When the network operator is found, the display shows

REGISTERING to show that the EXPLORER 300 is registering itself on the

network.

• READY: The EXPLORER 300 is registered on the network.

The display may show a different text, for example if an error has occurred.

For further information, refer to the User Manual.

NOTE: When the display shows READY, the terminal automatically activates

the LAN interface if the cable is connected and the interface is enabled. If

you are not going to use the LAN connection, remove the cable or disable

the LAN interface to avoid being charged for any transmission through this

interface.

You are now ready to make phone calls, browse the Internet or check your

e-mails, send ﬁles, run a video conference and much more.

MAKING A CALL FROM THE EXPLORER®300

If you are using a Bluetooth handset, the handset must be paired and placed close

to the EXPLORER 300. For information on pairing, see the section BLUETOOTH

PAIRING at the end of this document.

To make a call from the EXPLORER 300, dial

00 <country code> <phone number> followed by # or off-hook key.

Example: To call Thrane & Thrane in Denmark: (+45 39558800), dial

00 45 39558800 followed by # or off-hook key.

MAKING A CALL TO THE EXPLORER®300

To make a call to the EXPLORER 300, dial

+870 <mobile number>

+ is 00 for Europe and many other countries.

CHOOSING AN INTERFACE FOR DATA CONNECTION

The EXPLORER 300 has two types of interface for data connection: LAN interface

and Bluetooth interface.

The following table shows some characteristics of each interface, to help you

choose the right interface for your application.

Interface Power Consumption Range

LAN High Up to 100 m of cable

Bluetooth Medium Wireless connection.

Up to 25 m depending on the transmitter in the

computer and on the transmission conditions.

MAKING A LAN CONNECTION

To make a LAN connection, simply connect the LAN cable between your computer

and the LAN connector on the EXPLORER 300, and start up the EXPLORER 300 as

described in the beginning of this document.

As soon as the display of the EXPLORER 300 shows READY, the connection is

established automatically.

You are now ready to browse the Internet, check e-mails, send ﬁles etc.

NOTE: For information on conﬁguration, refer to the User Manual.

MAKING A BLUETOOTH DATA CONNECTION

To make a Bluetooth connection, place the computer close to the EXPLORER 300

and start up the EXPLORER 300 as described in the beginning of this document.

If the computer is already paired with the EXPLORER 300, the connection is

established automatically when both devices are ready and have discovered each

other. Note, however, that if your Bluetooth connection is deﬁned as a dial-up

connection, you have to open the dial-up connection to activate the connection.

You are now ready to browse the Internet, check e-mails, send ﬁles etc.

NOTE: For information on conﬁguration, refer to the User Manual. For information

on Bluetooth pairing, refer to the next section.

BLUETOOTH PAIRING

NOTE: This section only describes how to pair devices in which you can enter a

passkey. For information on devices in which you cannot enter a passkey, such as

headsets, refer to the User Manual.

To pair a Bluetooth device, do as follows:

1. Start up the EXPLORER 300 as described in the beginning of this document.

2. Place your Bluetooth device close to the EXPLORER 300.

3. On your Bluetooth device, search for new devices and select the EXPLORER 300

when it is found.

The default Bluetooth name of the EXPLORER 300 is EXPLORER 300.

If there is more than one EXPLORER 300 in the list, you can use the MAC address

to locate the correct one. To see the MAC address of your EXPLORER 300, enter

the display menu system and select

PROPERTIES > TERMINAL > HARDWARE > MAC.

4. On your Bluetooth device, enter the passkey of your EXPLORER 300.

The default passkey is the serial number of your EXPLORER 300.

To see the serial number, look at the label on the back of the EXPLORER 300 or

enter the display menu system and select

PROPERTIES > TERMINAL > HARDWARE > UNIT SER. NO.

The new Bluetooth device is now paired and ready to communicate with the

EXPLORER 300.

NOTE: Maximum 2 devices can be paired with the EXPLORER 300. If you have

already paired 2 devices you have to unpair a device before you can pair a new

one. For information on how to unpair devices, refer to the User Manual.

ACCESSING THE WEB INTERFACE

To access the web interface, do as follows:

1. Connect a PC to the EXPLORER 300.

2. Start your Internet browser.

3. Enter the IP address of the web interface in the address ﬁeld.

The default IP address is 192.168.0.1.

To see the IP address in the menu system, select

PROPERTIES>TERMINAL> IP ADDRESS.

The web interface now opens in your browser. For information on how to use the

web interface, refer to the User Manual.

Andere Handbücher für Explorer 300

Inhaltsverzeichnis

Sprachen:

Andere Thrane&Thrane Touch-Terminal Handbücher

Thrane&Thrane

Thrane&Thrane TT-3000LRIT mini-C Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane TT-3710A EXPLORER 500 Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane TT-6007A Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane Explorer 727 Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane EXPLORER 122 Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane BGAN Thrane&Thrane Explorer 700 Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane Sailor 250 FleetBroadband Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane TT-3606E Handbuch

Thrane&Thrane

Thrane&Thrane Explorer 300 Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane EXPLORER 500 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung