Timeguard LED200WFB Handbuch
I n s t a llation & Ope r ating Instruction s
2x 10W LED Wi-Fi PIR
Twin Floodlight - Black
Model: LED200WFB
1
1. General Information
These instructions should be read carefully and retained for further
reference and maintenance.
Timeguard reserve the right to alter these instructions at any time.
Up to date instructions will always be available for download at
www.timeguard.com
2. Safety
• Before installation or maintenance, ensure the mains supply to the
luminaire is switched off and the circuit supply fuses are removed or the
circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or used for the
installation of this luminaire and install in accordance with the current
IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this luminaire is
fitted does not exceed the rating of the circuit cable, fuse or circuit
breaker.
• To clean use a clean dry cloth only. Do not use liquid cleaners.
3. Technical Specifications
• This luminaire is of class II construction
Note:
• Energy Usage: 17 Kwh/1000h
• Beam Angle (Per Spotlight): 120˚
• Lamp Adjustment Pan and Tilt: Left and Right 35°
,Downward 80°
• Mains Suppply: 230V AC 50Hz
• Lumen Output: 2000lm
• Colour Temperature: 3000K - 6500K
• Operating Temperature: -20°C to +50°C
• Back Box Mounting Hole Centres: 84mm
• IP Rating: IP55
2
•Motion Detection Range: Up to 10m at a 2.5m
mounting height
• Detection Angle: 140˚
• Full Light Time On Adjustment: 5 seconds to 60 minutes
• 2nd Stage Time On Adjustment: 1 minute to 8 hours
• Lux Adjustment: 10 to 1000 lux
• Standby Power Consumption: 0.5W
• PIR Warm Up Duration: 5-10 seconds (approx)
• Manual Override: Yes (App Based)
• Hi-Lo Dimming (2nd Stage Lighting): Yes (In App Configuration)
• CE / UKCA Compliant
• Construction: Polycarbonate
• Product Dimensions (H x W x D): 205mm x 195mm x 78mm
With Corner Bracket (H x W x D): 205mm x 195mm x 95mm
4. Operating Modes (Tuya Smart App)
Manual Override: Turn the light ON / OFF as required.
Temperature Wheel: Sets the colour temperature of the luminaire.
Delay Setting: Delay either the startup or shutdown times of the
luminaire.
Schedule: Setup timed ON/OFF parameters for the luminaire to
switch on/off during a 7 day period.
PIR Options: Enable or Disable the PIR.
Motion Distance: Change the PIR’s sensitivity settings.
Lux Adjustment: Change the PIR activation triggers based on the
ambient light i.e. trigger light when dark, after evenings or
after dusk.
Light Duration: ON time of the luminaire after triggered via the PIR.
Hi-Lo Dimming (2nd Stage Lighting): Set the brightness and
duration of the luminiare once there is no movement detected.
3
3
6. Selecting a location
A
5. Tuya Smart App Requirements
• Smartphone/Tablet with at least iOS 11.0 or Android 7.0.
Minimum requirements subject to Tuya Inc. and not Timeguard.
• WLAN-enabled router: 2.4GHz (Separate Band)
B
• The PIR has a number
of detection zones, at
various vertical and
horizontal angles as
shown. See image A
• The best all-round
coverage is achieved with the floodlight mounted at the optimum
height of 2.5 metres. See image B.
• Appropriate positioning of the PIR is
required to ensure optimum performance.
• The PIR is more sensitive to movement
across its field of vision than directly
towards it. Therefore position the floodlight so
that its PIR looks across the likely approach path where possible.
• Avoid positioning the floodlight where there are any sources of
heat in the detection area of its PIR (extractor fans, tumble dryer
or boiler exhausts etc.) including opposite any other light sources
such as other security floodlights.
• Reflective surfaces (e.g. pools of water or white painted walls) and
overhanging branches may cause false activation under extreme
conditions.
• During extreme weather the PIR may exhibit unusual behaviour.
This does not indicate a fault with the product. Once normal
weather conditions return, the PIR will resume normal operation.
4
7a. Installation
2
84mm
MOUNTING
SCREW x 2
1
This section covers installation without the use of the corner
bracket. If the corner bracket is required for installation refer
to section 7b Installation (Corner Bracket).
• Mark the position of the mounting holes on the wall
using the back box as a template (See image 1).
Drill the holes ensuring not to infringe
with any gas/water pipes or electrical
cables that may be hidden below the surface.
• Insert the rawl plugs into the holes.
• Pass the mains supply cables through the back box, using the
appropriate knockouts and cable entry points to prepare for
termination. Ensure the grommets are used to maintain the IP
rating of the luminaire.
• Fix the back box to the wall using the two mounting screws,
making sure it
is the correct
way up. Take care
not to over-tighten the
screws to prevent damage to
the back box. (See Image 2).
• The mains supply cable can now be terminated. Please refer to
section 8 (Connection Diagram).
5
7b. Installation (Corner Bracket)
3
• Mark the position of the mounting holes on the wall using the
corner bracket as a template (See image 3).
Drill the holes ensuring not to infringe with any
gas/water pipes or electrical cables that may be
hidden below the surface.
• Insert the rawl plugs into the holes. If mounted
to an external corner, as shown, there is a thin web of plastic
that needs to be removed with cutters before installation. The
corner bracket can also be used for internal corners (not shown).
• Fix the corner bracket to the wall using the two mounting screws,
making sure it is the correct way up. Take care not to
over-tighten the screws to prevent damage to the corner bracket.
• Pass the mains supply cable through the
back box, using the appropriate knockouts
and cable entry points to prepare
for termination. Ensure the
grommets are used to maintain
the IP rating of the luminaire.
(See Image 4)
• The back box can then be secured to the
corner bracket using the x4 Philips
screws. (See image 5).
• The mains supply cable can now
be terminated. Please refer to
section 8 (Connection Diagram).
5
Install
Mounting
Screws x4
Pass Through
Mains Supply Cable
4
Knockout
6
8. Connection Diagram
LE
ISOLATION
SWITCH
LN
E
230V AC 50Hz
MAINS SUPPLY
Note terminal E is for earth continuity only.
230V 50Hz Mains Supply
Live Supply (Brown or Red)
Neutral Supply (Blue or Black) to
Earth (Green/Yellow) to
L
N
E
N
• After the mains supply cable has been terminated.
Re-connect the luminaire to the back box ensuring that the
two lugs firmly latch on the left and right hand side,
indicated by a ‘click’.
5
7
9. Downloading App & Registration
Note: the mobile or tablet device must be connected to a 2.4GHz band
on the router. Pairing on the 5GHz band will result in pairing timing out
or being unsuccessful. Refer to your ISP (Internet Service Provider) on
separating the bands if required.
• Ensure your phone or tablet is connected to your local Wi-Fi
network.
• Download the Tuya Smart App onto your phone or tablet by
searching for ’Tuya Smart’ on Google Play or the App Store.
You can also scan the QR code below applicable to your device.
• Install the App and open it to the registration screen. Click on the #
’Register’ button.
• Tap ‘Agree’ to accept the privacy policy.
• Choose your region by selecting your ‘Country Code’. Enter your
email address and phone number and click ‘Get Verification Code’.
• Enter the verification code sent to the email address or phone
number that you provided. Once you have successfully entered the
code, the app will automatically move you to the password screen.
3
8
• Assign a password (this must be between 6 to 20 characters
including letters and digits) and click ‘Done’. The App home page
will now appear.
10. Pairing Your Device(s)
Note: if you are using a VPN, make sure this is disabled before
continuing, and ensure that the 2.4GHz Wi-Fi band is enabled for this
device, separate from the 5GHz band.
• Once you are on the home page of the Tuya Smart App press the
plus button ‘ ’ on the top right hand side of the app.
• Under the ‘Add Manually’ menu, select the ‘Lighting’ category on
the left hand side of the app. Then select ‘PIR Light (Wi-Fi+BLE)’
from the devices list.
• Turn the isolation switch off,on,off,on,off,on. The luminaire will
begin breathing (dim up/down) indicating pairing mode is active.
• Select the ‘Confirm the indicator is blinking or breathing’
option on the App, then press the ‘Blink quickly’ button to begin
the pairing process.
• Enter the Wi-Fi password for the network your mobile or tablet is
currently connected to and then press the ‘next’ button.
• Shortly into the pairing process, the luminaire will stop breathing
and become stable. This indicates that the device has joined the
network.
• Once the device has been added to your account you may assign it
a name or allocate it to a room location setup in the app.
11. Smart Home Assistant
For Smart Home Assistant services such as Google Home or Amazon
Alexa, follow the on-board instructions on the TuyaSmart App. This
can be found under the ‘Me’ section on the home page of the App.
Note: The Smart Home Assistant services supported by the TuyaSmart
App may change as it is a 3rd party App Service. Any services that may
be removed are the responsibility of TuyaSmart developers and not
Timeguard.
9
12. Controls Screen
1
1
2
3 4
2
Temperature Wheel: Sets the colour temperature of the
luminaire.
Manual Override: Switch ON/OFF the luminaire as
required. Note this is a permanent state.
3
Delay Setting: Delay either the startup or shutdown times
of the luminaire. Note this function reverses the current
state of the luminaire after a certain amount of time.
4
Schedule: Setup timed ON/OFF parameters for the
luminaire to switch on/off during a 7 day period.
Left: Warm White Right: Cool White
1
2
PIR Options: Enables or Disables the PIR.
Motion Distance: Change the PIR’s sensitivity settings.
3
Lux Adjustment: Change the PIR activation triggers based
on the ambient light i.e. trigger light when dark, after
evenings or after dusk.
4
Linked Devices: Trigger other Wi-Fi lighting when the PIR
is activated. (Device Grouping).
4
Event Records: Review when the luminare has been
triggered. (Log of events)
1
2
3
4 5
Inhaltsverzeichnis
Andere Timeguard Scheinwerfer Handbücher
Timeguard
Timeguard Sure time STFL10PIRB Handbuch
Timeguard
Timeguard LEDPRO10WH Montageanleitung
Timeguard
Timeguard LEDX10PIR Handbuch
Timeguard
Timeguard MLB500C Bedienungsanleitung
Timeguard
Timeguard LEDCST10PIRB Handbuch
Timeguard
Timeguard LEDPRO70B Handbuch
Timeguard
Timeguard LEDX10PIRWH Handbuch
Timeguard
Timeguard ECO42F Bedienungsanleitung
Timeguard
Timeguard MLW3000 Handbuch
Timeguard
Timeguard LED100PIRBE Handbuch
Timeguard
Timeguard LED88PIR Handbuch
Timeguard
Timeguard ECO Series Handbuch
Timeguard
Timeguard LED200PIRBE Handbuch
Timeguard
Timeguard LEDX20PIRBN Handbuch
Timeguard
Timeguard LEDSF10B Bedienungsanleitung
Timeguard
Timeguard LED100PIRBP Handbuch
Timeguard
Timeguard LEDX10PIRB Handbuch
Timeguard
Timeguard ECO36F Bedienungsanleitung
Timeguard
Timeguard ECO1FL Bedienungsanleitung
Timeguard
Timeguard MLB98 Handbuch
Beliebte Scheinwerfer Handbücher anderer Marken
VIZULO
VIZULO Micro Martin Benutzerhandbuch
EuroLite
EuroLite LED IP FL-100 SMD Bedienungsanleitung
Cooper Wheelock
Cooper Wheelock XB12 Bedienungsanleitung
Allen + Roth
Allen + Roth 17624-000 Bedienungsanleitung
ADJ
ADJ 4 STAGE PAK Bedienungsanleitung
Cooper Lighting
Cooper Lighting EGL91SW233 Bedienungsanleitung
