Timewatch TW6000DCLD Bedienungsanleitung
3
catalogue
1. Brief Introduction to the road gate machine................................................................ 4
1.1 Functional Features.......................................................................................................4
1.2 Product parameters.........................................................................................................4
2. Appearance size of the gate.................................................................................................5
3. Installation of the road gate machine............................................................................ 6
3.1 Construction preparation:...........................................................................................6
3.2 Circuit gate installation:.........................................................................................6
3.3 Gate bar installation (straight bar):.................................................................. 7
3.4 Spring balance:...............................................................................................................8
4. Introduction of the gate controller................................................................................ 9
4.1 Wiring instructions:.....................................................................................................9
4.2 Explanation of operating terms:............................................................................ 10
4.3 Key button function explanation:.......................................................................... 10
4.4 Display:...........................................................................................................................10
4.5 Parameter setting steps:...........................................................................................11
4.6 Learning and deletion of remote control coding:............................................ 11
4.7 DC brushless gate controller command list:...................................................... 11
4.8 Functional schematic diagram...................................................................................16
5. Road gate test.........................................................................................................................19
5.1 Gate bar position (levelness, verticality) adjustment:.............................. 19
7. Meaning of the digital pipe code.....................................................................................20
8. Appendix: Spring ratio table.............................................................................................21
4
1. Brief Introduction to the road gate machine
1.1 Functional Features
* Left and right movement is adjustable
* Road gate movement adopts crank shaker drive mechanism, compact structure, rigid
rigidity, convenient maintenance and operation;
* When the gate rod is in the horizontal or vertical state, the movement structure
is completely self-lock, which can effectively protect the reducer from external
force impact;
* Compared with the ordinary gate movement, the parts are reduced by about 20%, with
less faults;
* Road gate movement has the national invention patent and utility model patent,
the movement technology is in the domestic leading level;
1.2 Product parameters
* Product size: 340X272X1000 (mm)
* Power supply: 220V ± 10%, 50~60Hz
* Motor: 24V140W brushless secondary variable speed all copper DC motor
* Running speed: 2-6S adjustable / 0.8-2S adjustable
* Remote control distance: 30M
* Waterproof grade: IP45
* Working environment: -15~ + 70℃
* Box thickness: 1.5mm
5
2. Appearance size of the gate
Schematic diagram of the foot mounting hole
position
6
3.Installation of road gate machine
3.1 Construction preparation:
1. Determine the gate pre-installation position according to the selected
integrated gate direction and the field installation situation.
The gate is divided into left fixed gate and right gate, defined as follows:
facing the front of the main engine (no side of the main shaft), the right rod falls
to the left fixed gate, and the lever falls to the left direction is the right fixed
gate.As shown in the figure below:
Left and right fixed definition of road lock
2. Lay power line and control line according to the control room or post box
(separate power line and control signal line)
3. For the non-concrete foundation or the ground is not horizontal, do the gate
foundation according to the situation.
3.2 Circuit gate installation:
1. Place the box in the installation position, open the box to determine the
position of the expansion bolt and mark.
7
2. Remove the box and punch the mark with impact drill and place expansion bolts.
3. Place the box at the installation position, adjust the angle of the box, and
tighten the expansion bolt nut after horizontal.
3.3 Gate bar installation (straight bar):
8
Release all balance pull springs;
Turn the motor hand shake handle and turn the brake clip to the horizontal
position;
Remove the lever and lever outer splint, double head bolt, gasket and cover nut;
Place the splint and gate bar in the figure, insert the bolts, tighten the nut,
and secure the gate bar;
After the gate rod is installed, turn the motor hand shake handle to pull the
gate lever back to the vertical position and hang all the pull springs.
3.4 Spring balance:
Open the gate door and cover, loosen the two loose nuts (M6), loosen the two limit
screw (hexagonal M6X25), loosen one lock screw (hexagonal M12X50), loosen about 5mm.
Put the brake lever between 30 ° and 60 ° to loosen the external force, then the
balance between the brake bar and the spring; if the brake bar is moving upward,
the spring tension shall be reduced; If the brake bar is moving down, the spring
tension should be increased.
Increase spring tension, spring hang hole down; reduce spring tension, spring hang
hole up.
After the spring balance is adjusted, reset the gate rod and swing rod (see the left
and right gate diagram for details), pay attention to the position of the swing rod
can not be wrong, and tighten the loose screws and nuts;
Pretighten the spring to a certain tension, otherwise the gate bar will shake, and
the flower basket screw is easy to loose.
9
4. Introduction of the gate controller
Motor
source
Function button
status lamp
Definition of wiring
terminal
4.1 Wiring instructions:
1. The start, stop, off and public are the gate control signal input, which can be
connected to three manual buttons, and the camera opening input is connected to the
start and public, regardless of sequence.Close the gate input access to the off-gate
and public, regardless of order.
10
2. The ground sense and public are connected to the brake detector or radar output
signal to control the vehicle over the gate.
3. Anti-smash and public for infrared access.
4.2 Explanation of operating terms:
Long press: press and hold the button without release, such as: long press for 3
seconds for at least 3 seconds, until the LED display menu item and buzzer prompt.
Short press: release the button, do not exceed the long press time.
4.3 Key button function explanation:
The controller has four keys, from left to right are "lift / +", "drop / -", "menu
/ confirm" and "stop / cancel", which can set the various parameters of the
controller.
"Lift the gate / +": under the normal working state, press the button to lift the
gate. After entering the setting state, you can use the button to increase the menu
item and adjust the setting value upward.In the parameter set state, short press
add one at a time.
"Off / -": Press this key to go off. After entering the setting state, you can use
this key to reduce the menu items and adjust the setting value down.In the parameter
set state, press one minus each time.
Menu / Confirm: This key has 3 functions:
1. In normal working mode, press the key for 3 seconds to enter the menu item selection
state. The LED displays "P-XX", and then press "Lift / +" and "drop / -" to select
the menu item;
2. Press "Menu / confirm" under the menu item selection state to enter the setting
parameter state;
3. After the parameter is set, press it to save the exit.
"Stop / Cancel": when normal operation, the key is the stop function, the menu item
selection state is the exit setting state, press the key to exit the state and return
to the menu selection state, that is, the previous level menu, and the value set
is invalid.If there is no key operation within 15 seconds under the menu selection
status and parameter settings, the controller returns to operation after a buzzer
tap.
4.4 Display:
The controller has a three-bit LED display that can be used for gate operating status,
parameters, menu items and other letters
The display of interest.Display the controller version information after power, and
the initial position of the motor after 2 seconds.
11
4.5 Parameter setting steps:
It can be set by long pressing the Menu / Confirmation button for 3 seconds, and
the LED will display PXX.
Select the menu item by short pressing or long pressing "Lift / +" and "drop / -",
and add one once
Or subtract one, long press is continuous add or subtract.Press Menu again to set
up the specified item and press Stop /
Cancel the key to return to the previous level or exit the settings.When setting
for the specified parameters is complete, you must press " Menu
/ Confirm " key confirmation can not take effect.The parameters set by pressing the
Stop / Cancel key will not take effect.No in 15 seconds
With a button, the buzzer on the control board will ring loudly, exit the setting
state, and return to the normal working state.
4.6 Learning and deletion of remote control coding:
Press the "Lift / +" button in normal working mode to quickly enter the remote control
learning menu command.
1、Paired learning
Entering the remote learning menu item P-22 shows the number of currently
learned.Press any key of the remote control, learn the successful buzzer long sound,
and the LED shows the number of learned remote control plus one, after learning a
remote control can continue to learn the next, the maximum support of up to 200 remote
control.If it is a learned remote control, the buzzer calls rapidly three times
continuously, suggesting that the remote control has been learned.After the study
is completed, press the confirmation key to exit. Then the successful remote control
will have a corresponding response in the normal working state.
2、Clear the remote control
After entering the P-31 menu item, the number of currently learned remote
controls is displayed. Press confirm key to clear all learned remote controls, and
the number of remote controls is 0.
4.7 DC brushless gate controller command list:
Inhaltsverzeichnis
