TMC Reef Flow 2.0 Bedienungsanleitung
Instructions 3
Instruções 11
Instrucciones 19
Installations 27
Istruzioni 35
Reef Flow 2.0
ALL MODELS
2
3
INSTRUCTIONS FOR INSTALLATION AND USE
Important Safety Information - Please Read Carefully
• Caution: Do not use any power supply other than the one supplied with your genuine Reef Flow
2.0 pump.
• The use ofa different power supply will invalidate the guarantee.
• Always isolate the PSU from the mains electricity before installing orcarrying out any maintenance
to the pump. Caution: Reef Flow 2.0 controller is not waterproof and therefore must not be
mounted above the aquarium orsump,or in any position where it may accidentally fall into water or
be splashed by water,or in a humid environment.
• Only use the correctly-rated controller supplied with the pump, e.g the Reef Flow 2.0 8000
Controllerwith the Reef Flow 2.0 8000 pump.
• A label on the back of the controller denotes which pump it is designed for. Using the wrong
controllerwith the wrong pump will invalidate the guarantee.
• Powerto the pump must be supplied through a Residual Current Device (RCD) with a rated residual
operating current not exceeding 30mA.
• Neveroperatethe pump withoutwaterinside the impellerchamberorwithliquids at atemperature
higher than 95F/35C.
• To ensure the pump continues to maintain a steady water flow, it must be cleaned regularly to
ensure it does not become clogged with debris ordetritus.
• Do not operate any appliance if it has a damaged cord orplug, ifit is malfunctioning, or ifit has been
dropped ordamaged in any way.
• This unit is designed to be used indoors and is not suitable for any outdoorapplications.
• Ensure the ReefFlow 2.0 pump is securely installed before operating.
• Always leave a drip-loop in the pump cable to prevent water running down the cable and reaching
the controllerand powersource (see diagram below).
3
DISPOSE OF THIS UNITRESPONSIBLY
Check with your local authority for disposal information.
4
Model 4000 6000 8000 10000 16000
Flow rate 4000 l/h 6000 l/h 8000 l/h 10000 l/h 16000 l/h
Max.Power 15W 26W 26W 36W 52W
Pump Voltage DC12V DC24V DC24V DC24V DC24V
PSU Voltage 100-240V
50/60Hz
100-240V
50/60Hz
100-240V
50/60Hz
100-240V
50/60Hz
100-240V
50/60Hz
Dimensions
X x Yø mm
55 x 48ø mm 63 x 58ø mm 63 x 58ø mm 78 x 72ø mm 78 x 72ø mm
5
INTRODUCTION
The Reef Flow 2.0 pumps have been designed to simulate the natural currents found within
the reef environment. Using the supplied controller, you can choose from 3 wave patterns
and adjust the intensity and frequency of your selected wave, to ensure you can create an
environment appropriate foryour particular tank and its inhabitants.
INSTALLATION
1.Clean the glass where the pump is to be installed.
Please note: the ReefFlow 2.0 can be tilted and angled to yourdesired position.
Caution: You must ensure that the pump is secured in your desired position before
operating.
2. Submerge the pump completely and then rotate it back and forth to allow any trapped
air to exit the pump impeller housing.
3. Locate the pump in a position at least 15-20cm below the water surface, ensuring
there is adequate space around the pump to avoid resonance, vibrations and substrate
being sucked into the pump. Also make sure the power cable will exit the aquarium in a
convenient place for connecting to the controller.
Interchangeable nozzle Impeller Motor
Mounting magnet (internal) Mounting magnet (external)
1 2 3 4 5
6 7
6
Please note: The magnet brackets used on the Reef Flow 2.0 are extremely strong and
the force with which they attract each other could cause serious injury if the magnets
are not handled correctly.Therefore please read and take note ofthe following guidelines:
Caution: Never place your fingers or any other body part between the two halves of the
magnet.
Caution: Always slide magnets together and apart - do not allow magnets to slam
togetheras thiscoulddamagethemagnets,theaquarium glass,and/orcausethemagnets
to chip or shatter with a possible risk ofinjury to the user.
4. Secure the pump by gently sliding the magnet on the outside of the aquarium into the
correct position.
Please note: suitable fora maximum glass thickness of 15mm.
5.Secure the controllernearthe aquarium, (ensuring a drip loop is in place) in a dry and non
humid area (ideally on the outside ofthe cabinet - do not place the controllerin the cabinet
with a sump as this may be too humid). Connect the controller DC plug to the pump DC
connector.
6.With the mains power switched off,connect the PSU DC plug to the controllerDC input.
7.Ensuring thatthe pumpisfullysubmerged andall connectionsare made,switchthe power
on at the mains.The pump will enter its last used settings.
PUMP OPERATION
The pump has several functions to control output and wave type.
We advise you to speak with your local fish shop to determine which settings will be best for
the species of corals and the aquarium size you own.
A little experimentation is often required to achieve the best results, as no two set-ups or
scapes are the same.
7
Continuous Stream mode
Press the Intensity button to cycle the power intensity of
the pump from 10% to 100%. The LEDs will illuminate in
20% increments.
Reefmode
Press the Intensity button 1-10 to increase/decrease the
frequency between each Reef wave. The LEDs represent
pump power; illuminating at the same frequency as the
wave pattern.
OFF
Press and hold forapproximately 5 seconds to turn off.
Pulse mode
Press the Intensity button 1-10 to increase/decrease the
frequency of each Pulse wave. The LEDs represent pump
power; illuminating at the same frequency as the wave
pattern.
OPERATION OF THE DC CONTROLLER
Press the Mode button to cycle the Reef Flow 2.0 through the following:
4
8
5
4
3
2
1
Troubleshooting LED Error Codes
When LED 1 and 2 are flashing: Hardware protection active
• Check motor& check controller
When LED 1 and 4 are flashing: Over voltage detected
• Check PSU
When LED 1 and 5 are flashing: Under voltage detected
• Check PSU
When LED 2 and 3 are flashing: Software protection active
• Check motor& check controller
When LED 3 and 4 are flashing: Open circuit protection
active
• Check all connection cables and powercord to ensure all
are undamaged and connections are correct
• Ifthe above are ok,check the motor
When LED 4 and 5 are flashing: Impelleris jammed or
broken orpump is operating dry
• Check impeller forsigns ofblockages/damage and ensure
the Reef Flow 2.0 is fully submerged
Please note: When making any changes to the Wave Mode settings it is important that
you check and observe the effect any change made will have on your individual aquarium
and make sure that the wave intensity and frequency is suitable for yoursize aquarium and
its inhabitants.
Please note: In the event of a powercut, your Wave Mode settings will be saved.
9
MAINTENANCE
Caution: Always isolate the PSU from the mains electricity before installing or carrying out
any maintenance to the pump.
Regular maintenance will prolong the life ofyour pump and we recommend that you clean
it frequently to avoid any loss in performance ordamage to the motor.
Ensure algae,marine fauna and any otherdetritus does not foul or block the blades ofthe
impeller orthe guard as this will cause excessive noise and will damage the motor.
A blocked impellercould also reverse the flow direction, causing the pump to draw in water
ratherthan pump it out.
The impeller should be regularly checked forsigns of degradation and replaced as neces-
sary.
Please note:The impeller is not covered under the guarantee.
How to Clean the Pump
The pump comes apart easily formaintenance.
1. Unplug the pump from the mains electricity supply.
2. Carefully slide the magnet from the outside of the aquarium.
3. Remove pump from aquarium.
4. Gently twist and remove the impeller guard.
5. Remove impeller,and clean with fresh water.
6. Rinse all parts with fresh water,and use a soft brush to remove any debris/detritus
inside.
7. Inspect for wear and tear.
Useful tip: if yourpump is covered heavily with coralline algae,soak in a mild acid, such as
white vinegar,and scrub off algae before attempting to open.Rinse with fresh waterbefore
use.
10
TROUBLESHOOTING
Problem:The pump is not working
• Check poweris switched on.
• Check all connections.
• Check and ensure the pump is switched on.
• Check pump fordebris.
• Check impellerand impeller shaft bush is clean and clear.
Problem:There is a whining noise coming from the pump
• Due to the nature of the high speed and powerful flow of the DC motors, some whining
noise can be heard and is completely normal.
Problem: I can heara clicking noise and my pump is not running correctly
• Check impellershaft for damage.Replace if necessary.
GUARANTEE
This product,exceptforthe impeller,is guaranteed against defects ofmaterials and work-
manship for a period of 1 year from the date of purchase.This guarantee is only valid if the
receipt orother proof ofpurchase is also supplied when the unit is returned forrepair.
The guarantee covers the replacement ofany defective parts. In case of improper use,tam-
pering or negligence by the buyer/user,the guarantee is deemed to be void.
Postage and packing costs forany returns are the responsibility of the buyer/user.
Please note: Only use the correctly-rated controller supplied with the pump, e.g the Reef
Flow 2.0 4000 Controller with the Reef Flow 2.0 4000 pump. A label on the back of the
controllerdenotes which pump it is designed for.Using the wrong controllerwith the wrong
pump will invalidate the guarantee.
Inhaltsverzeichnis
Sprachen:
Andere TMC Aquarium Handbücher
TMC
TMC Reef Skim 100nano Bedienungsanleitung
TMC
TMC V2Skim Series Bedienungsanleitung
TMC
TMC Next Wave Tank 60 Bedienungsanleitung
TMC
TMC Reel Pulsar Connect LPS-6 Bedienungsanleitung
TMC
TMC Next Wave Tank 60 Bedienungsanleitung
TMC
TMC Optical Auto Top Up Bedienungsanleitung
TMC
TMC Kreisel Bedienungsanleitung
TMC
TMC Reef Guard 50 Aquarium Cover Bedienungsanleitung
TMC
TMC Next Wave Tank 85 Bedienungsanleitung
TMC
TMC Reef Pump Compact 500 Bedienungsanleitung
TMC
TMC REEF-Fill Compact Bedienungsanleitung
TMC
TMC aquaGro CO2 Compact Diffusers Bedienungsanleitung
TMC
TMC Auto Top-up IR Bedienungsanleitung
TMC
TMC V2 Pure Bedienungsanleitung
TMC
TMC Reef Photon Betriebsanleitung
TMC
TMC Reef Ion 30 Bedienungsanleitung
TMC
TMC Reef Flow 2.0 1000nano Bedienungsanleitung
TMC
TMC Reef Tide s Series Bedienungsanleitung
Beliebte Aquarium Handbücher anderer Marken
JBL
JBL PRO SILENT S-100 Bedienungsanleitung
Amtra
Amtra VEGA Bedienungsanleitung
JBL
JBL CRISTALPROFI i60 greenline Bedienungsanleitung
Aquatlantis
Aquatlantis Tecatlantis EASY LED UNIVERSAL 2.0 Bedienungsanleitung
Innovative Marine
Innovative Marine MightyJet 8500 Mini Betriebsanleitung
SuperFish
SuperFish Planty 25 Installationsanleitung
Royal Exclusiv
Royal Exclusiv Bubble King DeLuxe 300 Bedienungsanleitung
Sera
Sera Marin Precision Biotop LED Cube 130 Bedienungsanleitung
Commodity Axis
Commodity Axis ViaAqua Titanium Heater Bedienungsanleitung
Sander
Sander Ozonizer P 2000 Bedienungsanleitung
Hagen
Hagen HALF MOON Bedienungsanleitung
CPR
CPR CS150 Bedienungsanleitung