Toa EM-380-AM Bedienungsanleitung

INSTRUCTION MANUAL

GOOSENECK MICROPHONE EM-380-AM

Thank you for purchasing the TOA gooseneck microphone.

Carefully follow the instructions in this manual to ensure prolonged and trouble-free use of your equipment.

1. OVERVIEW

TOA's EM-380 gooseneck microphone has a unique shape and a high-quality condenser microphone designed for use in

conference rooms, places of worship and voice applications.

This product is equipped with an optional power supply that can be selected between battery power or phantom power.

2. FEATURES

l When you press the button, the microphone turns on or off.

l Operation of the microphone by selecting the battery or ghost switch on the back of the microphone.

l Use two "AA" size batteries.

3. BEFORE USING THE UNIT

Prepare two AA (3 VDC) batteries or phantom power from 9 to 52 VDC to operate the unit.

4. NOMENCLATURE AND FUNCTIONS

5. BATTERY

5.1. Life expectancy

The application and use of the battery for speech and voice is assumed, as shown in the following table

Application

3 hours / week

3 hours / day

Times*

Discourse

20 months

3 months

Paging

92,500

※Approximately it is assumed to use a time voice de 10 seconds

Foam Filter

(Accessory)

[Rear]

[Bottom]

1. Microphone

Closed type cardioid electret condenser microphone.

The gooseneck shaft makes it easy to position the microphone

for optimal acoustic effect.

2. Gooseneck lamp

Light blue when the microphone is on and will turn off when the

microphone is in off mode.

3. Ignition lamp

Like the gooseneck lamp, the power lamp will turn on when the

microphone is on and turn off when the microphone is off.

Note: If the battery is low, the lamp will turn off, but the

microphone can still be used.

It is recommended to change the battery when this happens.

4. Microphone on/off button

Press this key to turn the microphone on or off.

5.XLR Output Balance

The microphone output impedance is 750 ohms.

Use the supplied cable to connect it to an amplifier.

6. Selector

Select this switch to use battery or phantom as the power supply

for this unit.

Note: It is recommended to use the supplied cable or a b-to-

lance cable, especially if you use phantom power. Otherwise,

the gooseneck lamp and the ignition lamp are dimly lit, although

the unit may function normally.

7. Battery compartment

Place AA batteries (2 pcs).

5.2. Battery insertion

Step 1. Open the battery cover.

Step 2. Insert batteries according to the polarity of the battery and make sure that the tape

remaining is on top of the batteries. (see image on the right).

Step 3. Put the battery cover back on the product.

Caution: If the microphone is not to be used in more than 1 month, remove the battery from the unit to

prevent battery leakage. To remove the batteries, carefully pull the remaining tape from the

battery compartment.

6. CONNECTION

Step 1. Place the amplifier microphone volume control

in the minimum position.

Step 2. Use the supplied cable to connect the microphone

the microphone unit to the microphone input of the amplifier.

7. OPERATION

Step 1. Press the ON/OFF button on the microphone.

The gooseneck lamp and the power lamp turn on and turn on the microphone.

Step 2. Make an announcement.

Keep your mouth at a distance of 5 to 10 cm from the microphone and speak normally for the best playback of

sound possible. Adjust the microphone orientation for the best position by rotating the axis of the gooseneck. If the distance from

the mouth is too close, this causes distortion of the voice, just the microphone by pulling it or lowering it, because the microphone

is of high sensitivity.

Step 3. Once the announcement is complete, press the ON/OFF button on the microphone.

Both the unit lamp and microphone will turn off.

Note: Be sure to press the ON/OFF button after completing the ad. Failure to do so reduces battery life.

8. USING SELECTOR SWITCH MODE

The selector switch has 2 modes. There is battery mode and ghost mode. If you use the battery as a power input, select the switch to the

battery position. And if you use ghost as an energy input, select the ghost position. Be sure to turn on the phantom power from the

amplifier or mixer. For reference, you can use the phantom power of TOA mixer amplifiers.

9. ONES SPECIFICATION

Element

Condenser microphone

Polar Pattern

Cardioid

Rated impedance

750 Ohms, balanced

Nominal sensitivity

-41 ± 3 dB (1 kHz 0 dB = 1 V/Pa)

Power Source

3 VDC (2 "AA" batteries) or phantom power (9 - 52 VDC)

Frequency response

50 - 16,000 Hz

Operating Temperature

0°C to +40°C (32°F to 104°F)

Finish

Support = Resin ABS, black, paint

Axis = Aleation of copper, black, paint

Dimensions

110 (w) x 145 (d) x 532 (h) mm

Weight

550 g (without batteries)

Accessories

Foam Filter .... 1

XLR cable to TRS connector (Phone Jack) (7.5 m) ... 1

Andere Toa Mikrofon Handbücher

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

Shure

Shure WH30TQG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

Shure

Shure KSM141 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

Shure

Shure MXA710 Series Bedienungsanleitung