Tokyo Electronic CS8320B Bedienungsanleitung
CCD Camera
CS8320B (EIA), CS83208C (CCIR)
Technical Manual
TOKYO ELECTRONIC INDUSTRY CO.,LTD.
CONTENTS
1. RESTART-RESET…………………………………………………………………………………………………… 9
2. Relation between the storage time and
the Image output at RESTART-RESET operation……………………………………………………. 9
3. Typical Examples of RESTART-RESET Operation………………………………………………….. 11
4. SPECIAL SHUTTER………………………………………………………………………………………………… 12
5. Image Output in RESTART-RESET Operation ………………………………………………………. 15
6. Explanation of internal selection switches………………………………………………………………... 16
NOTE
The falling pulse-phase of R.R pulse shall correspond to HD-falling phase or 1/2 HD
phase within ± 5 µ sec.
2. Relation between the storage time and the Image output at RESTART-RESET
operation
(1) RESTART operation
QSetting inside of the camera
CONTROL BOARD S4-3 ; ON
When RESTART-RESET operation, the signal stored during STORAGE A period can be output in the
period of IMAGING A as the below diagram.
- 9 -
1. RESTART-RESET
When normal external sync operation by HD-VD, the system cannot work normally without
consecutive VD every field (1V) as the below diagram.
QVD, at external SYNC operation by HD-VD
EXT VD
When RESTART-RESET operation, R.R pulse, can be fed with any timing as illustrated
with the below.
R. R
RESET
p
oint RESET
p
oint
QFRAME STORAGE MODE
RESET point
R. R
Ima
g
e
out
p
ut
QFIELD STORAGE MODE
RESET
p
oint
R. R
Image
output
(2) Slow speed shutter operation
QSetting inside of the camera
CONTROL BOARD S4-3 ; ON
When slow speed shutter operation, the signal stored in STORAGE A period can be output
during the period of IMAGING A as the below diagram.
Q
FRAME STORAGE MODE
R.
R
Image
output
- 10 -
QFIELD STORAGE MODE
R. R
Image
output
3. Typical Examples of RESTART-RESET Operation
Random shutter operation, obtained one fame image, combined with RESTART-RESET and
strobe light.
QSetting inside of the camera
CONTROL BOARD S4-3 ; ON
The strobe light is flashed by R.R (reset point). And the signal stored while strode light flashed
can be obtained at IMAGING A and IMAGING B as the below diagram. Then, the frame image
can be obtained without waiting time.
QFRAME STORAGE MODE
RESET point RESET point
Strobe
light
Image
output
R. R
- 11 -
QFIELD STORAGE MODE
RESET point RESET point
R. R
Strobe
light
Image
output
4. SPECIAL SHUTTER
(1) Relation between VD and readout timing
Relation VD and readout timing (SO) in CS8320B/CS832OBC is as follows.
The rising point of SG pulse comes to the timing to make the electronic shutter close.
VD or
R. R
SG
-
12
-
Model Scanning field T
1st field 614.2 µ sec.
CS8320B
2nd field 587.4 µ sec.
1st field 971.3 µ sec.
CS832OBC
2nd field 944.4 µ sec.
(2) Electronic shutter by shutter trigger
QSetting inside of the camera
CONTROL BOARD S4-4 ; ON
* In case of operation with RESTART-RESET it requires to set S4-3.
* When internal sync operation, HD/VD are fed from camera.
The electronic shutter opens from approximately 2 µ sec. after the shutter trigger pulse rises up,
and closes at the rising point of SG pulse. In this case, by feeding and controlling phase-
difference between the rising pulse of the shutter trigger and VD falling, X µ sec., it is possible
to set any shutter speed. At this time, the shutter speed is defined by X+T.
Combined with RESTART-RESET, variable random electronic shutter can be performed.
Shutter
trigger
VD or
R. R
SG
SUB
NOTE
When the next trigger inputs, during one field period, active image period, right after
the shutter trigger, when image is output successively, sometimes, a scratch image
maybe occurred.
In that case, when the rising-phase of shutter trigger is in the active image period,
use to make the rising shutter trigger correspond with HD falling phase.
When only one field is output, it is possible to input with any phase.
- 13 -
(3) Typical example of SPECIAL SHUTTER
The method to make random shutter operation with frame image combined with
RESTART-RESET and SPECIAL SHUTTER
(But the image of the first field and the 2nd field is not the same time image.)
QSetting inside of the camera
S 4-3; ON
CONTROL BOARD
S4-4; ON
By feeding and controlling the rising phases of shutter trigger and R.R pulse, the signal to be
stored during STORAGE A is output at IMAGING A, and the signal stored during STORAGE B
is output from IMAGE B. Then, the frame image right after shutter trigger can be obtained
without waiting time.
QFRAME STORAGE MODE
RESET point RESET point
R. R
Shutter
trigger
Image
output
NOTE
When the next trigger inputs, during one field period, active image period, right after
the shutter trigger, when image is output successively, sometimes, a scratch image
maybe occurred.
In that case, when the rising-phase of shutter trigger is in the active image period,
use to make the rising shutter trigger correspond with HD falling phase.
When only one field is output, it is possible to input with any phase.
- 14 -
QFIELD STORAGE MODE
RESET point RESET point
R. R
Shutter
trigger
Image
output
5. Image Output in RESTART-RESET Operation
When RESTART-RESET operation in CS8320B and CS8320BC, V. SYNC and V.BLK are not
generated in the composite image signal right after R.R (reset point), one field period, but the
phase relation between reset timing (VD) and the image output does not change at all compared to
the normal operation.
QImage output in normal mode
T
hey are output from CCD,
but they are erased by V. BLK
V
D
Image
output
R. R
Image
output
V
.SYNC is generated.
QImage output right after resetting
Y. SYNC is ungenerated
- 15 -
CCD output as output, as it is
since V. VLK is un
g
enerated.
6. Explanation of internal selection switches
The internal stricture of this camera is as shown in the figure below.
QSide view after opening the camera cover
QMethod of setting the different modes
The different modes can be set using the switch S4 in the CONTROL board. The mode can be
selected by moving the DIP switches 1 to 6 to the left or the right position. Each
switch becomes OFF in the left position and ON in the right position.
At the time of shipment from the factory, all the switches will have been set to the left position.
-
16
-
Switch setting position
No. Function name
OFF ON
1 Gamma correction 1.0 0.45
2 CCD operation mode Frame store Field store
3 Restart-Reset OFF ON
4 Special shutter OFF ON
5 Not used ------------------- -----------------
6 VD/FLD output VD output FLD output
Andere Handbücher für CS8320B
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Tokyo Electronic Sicherheitskamera Handbücher
Tokyo Electronic
Tokyo Electronic CS3730DC Bedienungsanleitung
Tokyo Electronic
Tokyo Electronic CS3910H Bedienungsanleitung
Tokyo Electronic
Tokyo Electronic CS8550i-01 Bedienungsanleitung
Tokyo Electronic
Tokyo Electronic CS9200 Bedienungsanleitung
Tokyo Electronic
Tokyo Electronic CS8320B Bedienungsanleitung
Tokyo Electronic
Tokyo Electronic CS8530-01 Bedienungsanleitung
Tokyo Electronic
Tokyo Electronic CS8541D series Bedienungsanleitung
Tokyo Electronic
Tokyo Electronic CS8550D Bedienungsanleitung
