TomTom GO Bedienungsanleitung

TomTom GO

What’s in the box1.

What’s in the box aTomTom GO

AOn/Off button

BMicrophone

CLight sensor

DSpeaker

EMemory card (micro SD

card) slot

bActive Dock cUSB car

charger

dUSB cable eDocumentation

pack

Before you start2.

Before you start

Switching on and off

Install your TomTom GO navigation device in your car following the instruc-

tions in the installation section at the start of this book.

To switch on your navigation device, press and hold the On/Off button until

you see the start-up screen. The first time you switch on your device, it may

take a short time to start.

Setting up

When you first switch on your device, you have to answer a few questions to

set up the device. Answer the questions by tapping the screen.

Youareaskedwhetheryoumakeregulartripstothesamelocations.Ifyoutap

YES, you can enter these destinations as your favourite destinations. Every

time you switch on your device, you can immediately select one of these loca-

tions as your destination.

To change these destinations or select a new destination, tap Start-up

preferences in the Preferences menu, then select Ask for a destination.

Device not starting

In rare cases, your TomTom GO navigation device may not start correctly or

may stop responding to your taps.

First, check that the battery is properly charged. To charge the battery, con-

nect your device to the car charger. It can take up to 2 hoursto fully chargethe

battery.

If this does not solve the problem, you can reset the device. To do this, press

and hold the On/Off button for 15 seconds and release the button when your

device begins to restart.

Battery notes

ThebatteryinyourTomTom GOnavigationdevicechargeswhenyouconnect

it to the car charger or to your computer.

When you connect your device to a computer, you are asked if you want to

connect to the computer. If you select No and then do not tap the screen

within three minutes, the devicewill automatically switch off. This happens so

that the battery can charge faster.

Note: You should plug the USB connector directly into a USB port on your

computer and not into a USB hub or USB port on a keyboard or monitor.

Active Dock

Use the Active Dock to install your TomTom GO inside your car.

Make sure that both the Active Dock and your windscreen are clean and dry

beforeyouattach the holder.Placethe ActiveDockso that itdoesnotinterfere

with your view of the road or of any of the controls in your car.

ToattachtheActiveDock, press the suction cup firmly against the windscreen

on an area where the glass is flat. Then twist the rubber grip near the base of

the Active Dock in a clockwise direction until you hear a click.

GPS reception

When you first start your TomTom GO navigation device, the device may

need a few minutes to determine your GPS position and show your current

position on the map. In future, your position will be found much faster, usually

within a few seconds.

To ensure good GPS reception, you should use your device outdoors. Large

objects such as tall buildings can sometimes interfere with reception.

The TomTom GO 950 includes Enhanced Positioning Technology or EPT. EPT

automatically estimates your position when the GPS signal is lost while you

are driving, such as when you are in a tunnel. When EPT is in use, the EPT

symbol is shown in the Driving View.

Take care of your device

Neverleave yourTomTom GO navigationdeviceoraccessoriesonviewwhen

you leave the car as they may become an easy target for thieves.

You can set a password which must be entered every time you start your

device.

It is important to take care of your device.

• Your device is not designed for use in extreme temperatures and any such

exposure may cause permanent damage.

• Do not open the casing of your device under any circumstances. Doing so

may be dangerous and will invalidate the warranty.

• Wipe or dry the screen of your device using a soft cloth. Do not use any liq-

uid cleaners.

Safety3.

Safety

Positioning the Active Dock

Consider carefully where to attach the dock in your car. The dock should not

block or interfere with any of the following:

• Your view of the road

• Any of the controls in your car

• Any of your mirrors

• The airbag

When your navigation device is in the dock, you should be able to reach the

deviceeasilywithoutleaningor stretching.The diagramsshowwhereyoucan

safely attach the dock.

You can attach the dock to the windscreen, side window or use a Dashboard

Mount Disk to attach the dock to your dashboard. TomTom also offers alter-

native mounting solutions for your TomTom navigation device. For more

information about Dashboard Mount Disks and alternative mounting solu-

tions, go to tomtom.com/accessories.

Installing the Active Dock

Make sure that both the Active Dock and your window are clean and dry.

1. Pressthe suction cup firmlyagainst the window on an area where the glass

is flat.

2. Twist the rubber grip near the base of the Active Dock in a clockwise direc-

tion until you hear a click.

The Active Dock is now installed.

Safety preferences

We recommend using the safety preferences to make your driving as safe as

possible. The safety preferences include, for example, the following options:

• Hide most menu options when driving

• Show safety reminders

• Warn when driving faster than allowed

You can also drive more safely by using voice commands to control your

TomTom GO.

Making your first journey4.

Making your first journey Planning a route with your TomTom GO navigation device is easy. To plan a

route, follow the steps below.

Important: For safety reasons, you should always plan a route before you

start your journey.

1. Tap the screen to bring up the Main Menu.

Note: The buttons on your navigation device are shown in full colour unless

a button is currently unavailable. For example, the button named Find alter-

native in the Main Menu is not available until you have planned a route.

2. Tap Navigate to...

3. Tap Address.

When you enter an address, you can choose from the following options:

•City centre - tap this button to set your destination as the centre of a city

or town.

•Street and house number -tap thisbuttonto setanexact addressasyour

destination.

•Postcode - tap this button to enter a postcode as your destination.

Note: You can enter a postcode for any country. In some countries, postcodes

are detailed enough to identify a house on their own. In other countries you

can enter a postcode to identify a town or area. You will then have to enter a

street and house number.

•Crossing or intersection - tap this button to set your destination as the

point where two streets meet.

•Spoken address - tap this button to set your destination by saying the

address to your navigation device.

In this example, we will enter an address.

4. Tap Street and house number.

Note: When planning a trip for the first time your navigation device asks you

to choose a state or country. Your choice is saved and used for all routes you

plan.

You can change this setting at any time by tapping the flag.

5. Start to type the name of the town where you want to go.

As you type, the names of the towns that match what you have typed are

shown. When your destination appears in the list, tap the name of the town

to set the destination.

Tip: Instead of typing the name, tap this button to say the address by

speaking to your navigation device.

6. Start to type the street name. Tap the name when it is shown in the list.

As with the name of the town, the names of the streetsthat match what you

have typed are shown. When your destination appears in the list, tap the

name of the street to set the destination.

7. Enter the house number and then tap Done.

8. Your navigation device asks if you need to arrive at a particular time. For this

exercise, tap NO.

The route is calculated by your device using IQ RoutesTM.

IQ Routes is used to plan the best possible route using information about

the average speeds measured on the roads.

When the route has been calculated, tap Done.

Your TomTom GO navigation device begins to guide you to your destination.

Route summary

After planning a route, you see a summary of your route.

The route summary shows an overview map of your route and the total jour-

ney time including delays caused by both incidents and busy roads.

You can see the route summary at any time by tapping the right side of the

status bar.

Using your voice to plan a route

Instead of tapping the screen to plan a route, you can use yourvoice to plan a

route.

For information about the different ways you can plan a route using your

voice, see Voice command and control.

Frequent destinations

If you often make trips to the same destinations, you can set your device to

ask if you want to plan a route to one of these locations every time the device

starts. This is faster than planning a route in the normal way.

Toselecta new destination,tapStart-up preferences in thePreferencesmenu

then select Ask for a destination. You are asked if you want to select a new

destination and you then need to answer a few questions about the location.

Show my list of frequent destinations every time my TomTom GO starts

You can set your TomTom GO to ask if you want to plan a route to one of your

frequently visited destinations, every time the device starts.

To change this setting, do the following:

1. Tap Start-up preferences in the Preferences menu and then select Ask for

a destination.

2. Tap Yes, then tap Yes again to begin entering information about the desti-

nation.

3. Select a symbol for the destination and tapDone to set thesymbol, then tap

Yes.

Tip: If you want to choose a title of your own, select a numbered symbol.

4. Tap Yes and if required enter a new name, then tap Done.

5. Enter the address details in the same way you enter an address when plan-

ning a route, then tap Done.

6. If you want to set more destinations, repeat the steps above. Otherwise, tap

Done.

You are asked if you want to change the start-up image.

7. If you want to change the image, follow the instructions shown on the

screen. Otherwise, tap No.

Every time your TomTom GO starts, you are asked if you want to plan a route.

If you tap Cancel, you are shown the Main Menu.

Arrival times

When you plan a route, your TomTom GO asks you if you need to arrive at a

particular time.

Tap YES to enter a preferred arrival time.

Your GO calculates your arrival time and shows you whether you will arrive

on time.

You can also use this information to work out when you need to leave. If your

GO shows that you will arrive 30 minutes early, you can wait and leave in 30

minutes time, rather than arrive early.

Yourarrivaltime isconstantlyrecalculatedduring yourjourney.The status bar

shows whether you will arrive on time or if you are going to be late, as shown

below:

You will arrive 55 minutes before the arrival time you entered.

If the estimated arrival time is more than five minutes before

the time you entered, it is shown in green.

You will arrive 3 minutes before the arrival time you entered.

If the estimated arrival time is less than 5 minutes before the

time you entered, it is shown in yellow.

You will arrive 19 minutes late.

If the estimated arrival time is later than the time you entered,

it is shown in red.

Other navigation options

When you tap Navigate to..., you can set your destination in many ways, not

just by entering the address. The other options are listed below:

Status bar

preferences

Tap Status bar preferences in the Preferences menu, to enable or disable

arrival time notifications.

Select the required options on the first menu screen and then tap Done.

To enable arrival time notifications, select Show leeway to arrival time.

Home

Tap this button to navigate to your Home location.

You will probably use this button more than any other.

Favourite

Tap this button to select a Favourite as your destination.

Address

Tap this button to enter an address as your destination.

Recent

destination

Tap this button to select your destination from a list of places you have

recently used as destinations.

Point of

Interest

Tap this button to navigate to a Point of Interest (POI).

Point on map

Tap this button to select a point on the map as your destination using the

map browser.

Latitude

Longitude

Tap this button to enter a destination using latitude and longitude values.

Position of

last stop

Tap this button to select your last recorded position, as your destination.

Andere Handbücher für GO

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TomTom GPS Handbücher

TomTom

TomTom 1N01.081 Bedienungsanleitung

TomTom

TomTom Go Series Bedienungsanleitung

TomTom

TomTom GO 740 Live Bedienungsanleitung

TomTom

TomTom 2004 Bedienungsanleitung

TomTom

TomTom GO Bedienungsanleitung

TomTom

TomTom Go 2535M LIVE Bedienungsanleitung

TomTom

TomTom Car Navigation System TomTom Toyota Bedienungsanleitung

TomTom

TomTom Traffic Receiver Bedienungsanleitung

TomTom

TomTom XL 540S - Widescreen Portable GPS Navigator Bedienungsanleitung

TomTom

TomTom One XL Bedienungsanleitung

TomTom

TomTom Go 630 Bedienungsanleitung

TomTom

TomTom NAVIGATION SYSTEM Bedienungsanleitung

TomTom

TomTom RIDER Bedienungsanleitung

TomTom

TomTom Go 520 Bedienungsanleitung

TomTom

TomTom 4YB60 Leitfaden

TomTom

TomTom Connect Bedienungsanleitung

TomTom

TomTom LTO 200D Bedienungsanleitung

TomTom

TomTom GO 740 LIVE Bedienungsanleitung

TomTom

TomTom RIDER Bedienungsanleitung

TomTom

TomTom ONE Bedienungsanleitung

TomTom

TomTom Golfer Bedienungsanleitung

TomTom

TomTom VIA Bedienungsanleitung

TomTom

TomTom GO CLASSIC Bedienungsanleitung

TomTom

TomTom GO Bedienungsanleitung

Beliebte GPS Handbücher anderer Marken

Raven

Raven Cruizer II Handbuch

Hama

Hama 53118 Bedienungsanleitung

Garmin

Garmin SOUNDER 125 Bedienungsanleitung

Garmin

Garmin DEZL 580 Bedienungsanleitung

Jigabot

Jigabot EX Bedienungsanleitung

Pointer

Pointer Cellocator CelloTrack XT LTE Installationsanleitung

Queclink

Queclink GV55LITE Bedienungsanleitung

Voxson

Voxson Voxtrack GPS500 Gebrauchsanweisung

Garmin

Garmin ECHOMAP PLUS Bedienungsanleitung

Starcom Systems

Starcom Systems Kylos Compact Bedienungsanleitung

Garmin

Garmin 15 H Series Bedienungsanleitung

Cobra

Cobra Marine MC 600Ci Bedienungsanleitung

Cellocator

Cellocator CelloTrack T Bedienungsanleitung

Enfora

Enfora Mini-MT GSM2228UG001 Bedienungsanleitung

Magellan

Magellan eXplorist 100 Bedienungsanleitung

LTE

LTE G50B Bedienungsanleitung

Garmin

Garmin DEZL OTR500 Bedienungsanleitung

SkyGolf

SkyGolf SkyCaddie SG1 Bedienungsanleitung