ToolKitRC M6DAC Bedienungsanleitung
@ ToolkitRC 2021
1
M6DAC
Manual V1.0
2021.05
www.toolkitrc.com
ToolkitRC Technology (Shenzhen) Co.. Ltd
@ ToolkitRC 2021
2
Introduction
Thank you for purchasing the ToolkitRC M6DAC
dual balance charger, please read this manual carefully
before use.
Key Points
Tips
Important
Information
Further information
To ensure you have the best experience with this
product please scan the QR code below to stay up to
date with news, information and firmware updates for
your charger. Or visit www.toolkitrc.com
WeChat QR Code
@ ToolkitRC 2021
3
Safety
1，M6DAC allows input voltage of 7-28V or AC
100-240V. Please ensure that the power supply
voltage is in line with this range. Pay attention to the
positive and negative polarities of the power supply
when connecting.
2，Do not use this product in a hot area or near a heat
source. Do not use this product in a damp, flammable
or explosive gas environment.
3，Only use this product while under direct supervision.
No not leave charging batteries unattended.
4，When not using this product, please unplug the
input power in time.
5，When using the charging function, please set the
current matching with the battery. Don’t set excessive
current charging, so as not to damage the battery.
@ ToolkitRC 2021
4
Contents
Introduction.......................................................... 2
Key Points............................................................. 2
Further information............................................. 2
Safety..................................................................... 3
Contents................................................................4
M6DAC Layout.....................................................8
Charge and discharge settings....................... 11
1，Battery type...................................................11
2，Number of cells........................................... 13
3，Mode............................................................. 15
4，Discharge mode.......................................... 15
5，Input MaxVoltage........................................17
6，End voltage（TVC）...................................18
7，Current setting.............................................19
8，NiMH setting (PeakV)................................. 20
9，Cycle setting.................................................20
@ ToolkitRC 2021
5
10，Power mode setting..................................22
11，Smart battery.............................................. 24
Charge and discharge work............................ 26
System settings.................................................. 30
Other functions..................................................34
Specification....................................................... 36
@ ToolkitRC 2021
6
Product description
M6DAC is a dual-channel balanced charger
product. Small size, high power density, innovative
design, charging accuracy can be as low as 5mV.
Built-in 200W AC power supply.
Charge, discharge and balance management of
LiPo, LiHV, LiFe Lion 1-6S, NiMh 1-16S, PB 1-10S
batteries.
Charging current：
Synchronous mode maximum 25A@MAX700W
Asynchronous mode maximum 15A@MAX350W
Discharge current：
Recycle mode maximum 15A @350W *2
Normal mode maximum 3A @15W *2
65W fast charge USB-C output.
PD/QC/AFC/FCP/SCP/PE/SFCP/etc. full protocol.
Lithium battery cut-off voltage can be set (TVC
function).
Constant current and constant voltage output,
customizable 1-28V constant voltage, 1-15A
constant current.
@ ToolkitRC 2021
7
Can be adapted to mainstream UAV batteries,
automatically activated and charged.
Multi-language system, can arbitrarily upgrade the
required language.
The device connects to PC like a USB drive for easy
firmware upgrades. Simply copy and paste new
firmware files to update.
@ ToolkitRC 2021
8
M6DAC Layout
Front
Back
Scroll wheel
Turn: left or right Press: OK
Display
Main port*2
Balance port*2
DC input
Cooling fan
USBC output &upgrade
Exit/CH Key
Temp. Sensor Port
AC input
States LED*2
@ ToolkitRC 2021
9
Quick start
1，Connect a 7-28V or AC 100-240V power supply or
input battery to the input port on the back of the
M6DAC.
2，The display shows the boot logo and stays for 2
seconds.
3，At the same time accompanied by do-re-mi's boot
sound.
4，After booting, the display will enter the main
interface and display as follows:
5，Short press [Exit/CH], the cursor switches between
the left and right channels.
6，Press and hold [Exit/CH] to start testing the internal
resistance of the corresponding channel. After the test,
the internal resistance will be displayed.
7，Scroll [Scroll Wheel] to switch the pages in the
corresponding channel.
@ ToolkitRC 2021
10
8，Short press [OK], can select the charging task when
the channel is idle and can adjust and end the work
when the channel is working.
9，Press and hold [OK] to enter the system setting
interface when both channels are idle.
10，Press [Exit], to end the modification or return to the
previous interface.
=================================
1，Short press [Scroll Wheel] once，to confirm the
key function
2，Press and hold [Scroll Wheel] for 2 seconds，to
delete the key function
3，If any key is operated successfully, there will be a
di-di prompt tone.
=================================
Inhaltsverzeichnis
Andere ToolKitRC Akkuladegerät Handbücher
ToolKitRC
ToolKitRC M6D Bedienungsanleitung
ToolKitRC
ToolKitRC M8 Bedienungsanleitung
ToolKitRC
ToolKitRC Q4AC Bedienungsanleitung
ToolKitRC
ToolKitRC Q6AC Bedienungsanleitung
ToolKitRC
ToolKitRC M6 Bedienungsanleitung
ToolKitRC
ToolKitRC C3 Bedienungsanleitung
ToolKitRC
ToolKitRC C6 Bedienungsanleitung
ToolKitRC
ToolKitRC C4 Bedienungsanleitung
ToolKitRC
ToolKitRC M4 Pocket Bedienungsanleitung
ToolKitRC
ToolKitRC M9 Bedienungsanleitung
