Topcon Positioning Group NORAC UC5 Bedienungsanleitung
Severe Terrain Option
Large Flange Low Profile Brackets - Stoll
Installation Manual
5465BC-LP-ST
Copyright 2017 by NORAC Systems International Inc.
Reorder P/N: 5465BC-LP-ST-INST Rev A (Severe Terrain Option Large Flange Low Profile
Brackets - Stoll)
NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and
without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information
contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.
Contents
1Introduction................................................................................................................ 1
2Kit Parts ...................................................................................................................... 2
3Ultrasonic Sensor Installation .................................................................................. 4
4Cable Drawings .......................................................................................................... 9
1
1Introduction
Please take the time to read this manual completely before attempting to install the system. A
thorough understanding of this manual will ensure that you receive the maximum benefit from
the system.
Your input can help make us better! If you find issues or have suggestions regarding the parts
list or the installation procedure, please don’t hesitate to contact us.
Every effort has been made to ensure the accuracy of the information contained in
this manual. All parts supplied are selected to specially fit the sprayer to facilitate
a complete installation. However, NORAC cannot guarantee all parts fit as
intended due to the variations of the sprayer by the manufacturer.
Please read this manual in its entirety before attempting installation.
2
2Kit Parts
2.1 Kit Overview
Figure 1: Severe Terrain Parts
3
2.2 List of Parts
Item Part Number Name Quantity
B05 44706-01 KIT CABLE TIE BLACK 10 PCS 21 IN 150 PCS 7.5 IN 1
B21 44973 SENSOR MOUNTING BRACKET LOW PROFILE 16 GA LARGE FLANGE 2
C06 43210-10 CABLE NETWORK 18 AWG 10M 2
E05 43750 ULTRASONIC SENSOR 2
E10 43760 NETWORK COUPLER 3-WAY 2
M02
5465BC -LP-ST-INST
SEVERE TERRAIN OPTION - LF LOW PROFILE BRACKETS - STOLL 1
Do not use high speed power tools/drills when installing hardware.
The use of dielectric grease is not recommended on any NORAC electrical
connections.
To ensure all stainless steel hardware does not gall or seize apply a light coating of
the supplied Permatex Anti-seize grease to all threaded parts upon installation.
Permatex Anti-seize lubricant is preferred, but other similar anti-seize products
may be used.
4
3Ultrasonic Sensor Installation
3.1 Ultrasonic Sensor Serial Number Arrangement
When installing the ultrasonic sensors, start with the smallest serial number on the left-hand
side, and proceed to the largest serial number on the right-hand side. Each ultrasonic sensor
has a serial number stamped on the sensor housing.
Apply a light coating of the supplied Permatex Anti-seize grease to all threaded
parts upon installation.
Figure 2: Sensor Serial Number Arrangement
Only the brackets shown in black are included in this kit.
The E07 sensors will be mounted in the positions shown in black.
A problem can arise if a sensor is not mounted correctly. It is possible for the
sensor to read off of the boom instead of the ground. This may only become
apparent once the control system is switched from soil to crop mode.
Be careful that the sensor bracket does not collide with any other part of the boom
when the boom is folded to transport position. If possible, mount the sensor
brackets while the booms are folded to ensure they will not cause interference.
5
3.2 Low Profile Bracket Mounting Guidelines
1. Minimize the distance between the bolts to prevent bending the bracket and prevent the
bracket from loosening over time.
2. Ensure the bracket is mounted tight against the bottom of the boom, minimizing the
distance between the boom structure and the angled flange.
Figure 3: Bracket Mounting Guidelines
3.3 Sensor Bracket Installation
1. The sensor bracket should be oriented forward (ahead of the boom).
2. Mount the sensor brackets onto the boom half way between the tip and center of the
sprayer.
Figure 4: Bracket Mounting Example
Front
6
Figure 5: Inner Wing Sensor Bracket Mounting
7
3.4 Ultrasonic Sensor Mounting Guidelines
The following guidelines will ensure optimal sensor performance and prevent sensor
measurement.
1. In its lowest position, the sensor must be 9 inches (230 mm) or more from the ground.
2. Ensure that there are no obstructions within a 12 inch (300 mm) diameter circle projected
directly below the center of the sensor.
3. The sensor should be approximately vertical at normal operating heights.
Figure 6: Sensor Mounting Guidelines
Figure 7: Bracket Mounting Guidelines
Andere Handbücher für NORAC UC5
1
Inhaltsverzeichnis
Andere Topcon Positioning Group Steuerungssystem Handbücher
