Topens TC186 Bedienungsanleitung
C030328 1 VER21a
User Manual of the WiFi Surveillance Camera
Built-in Relay Switch (Model: TC186)
1. Specifications
Pixel and resolution: 2M pixel (1080P)
Network connection: WiFi or Ethernet Cable
Sensor and lens: CMOS, 6mm
Night vision mode: ICR infrared filter type
Night vision distance: 15m
Working mode: Toggle or Self-hold Selectable
Maximum capacity of the Relay Contact: 10A/250VAC 10A/30VDC
2. Installation of the APP
You can search “LinkCraft”in Google Play or iOS APP store to download & install the
APP.
3. Installation of the Micro SD card
The camera supports an optional Micro SD card which storage could be up to
maximum 128GB. You can install the Micro SD card to recording the monitoring video
in the local card. You can find 4 screws on the bottom cover. Loosen the 4 screws and
you’ll find a card slot. Insert the Micro SD card into the card slot and then fix the little
plate back to the bottom cover to complete installation.
NOTE: The Micro SD card will record the monitor video after about 5 minutes when it’s
installed into the camera at the first time.
2
4. Wire connection with the Gate/Garage Door Opener
You can connect the BLUE wire and the YELLOW&GREEN wire to the exit or push
button terminals of the control board (no matter the polarity) to activate the gate opener.
3
5. Wire connection with the Automatic Industrial Equipment by
controlling the power supply directly
You can connect the YELLOW&GREEN wire (COM) to the LIVE LINE (or positive
electrode of power input) and connect the BLUE wire (NO) to LIVE (or positive) power
supply terminal of the equipment respectively. The Neutral power supply terminal of the
equipment can be connected to the Neutral Line directly. You can set the camera to
control the equipment via a timer (7 days * 24 hours).
4
6. Wire connection with the Automatic Industrial Equipment with remote
control terminals
You can connect the BLUE wire and the YELLOW&GREEN wire to the wired remote
control terminals of the equipment to control it via the camera.
7. Check the WiFi signal before adding the camera to your phone
5
8. How to Add the Camera to the Android Phone
NOTE 1: The camera can access the network via WiFi or Ethernet cable. The
configuration steps are the same as the WiFi when using the Ethernet cable. You
can input any WiFi name and password when configuring it with the Ethernet
cable.
NOTE 2: You must finish the configuration in 5 minutes, or the camera will quit
the configuration automatically after that. Max. 50 cameras can be added to your
phone.
NOTE3: The antenna should be installed vertically before configuration.
8.1 Open the APP and then click “register” to register a user account. Input your mobile
phone number or your email address and set you own account password. Click “Get
Verification Code” to send a code to your phone or your email box. Please input the
received code to the blank bar of “Verification code”. Finally click “register” to complete
the registration.
SET button
Indicator
6
NOTE 1: The APP will recognize the Country Code of the SIM card of your phone.
There is no need to input the Country Code when registering.
8.2 Ensure there is a WiFi network is available for your phone & the WiFi camera and
the phone has been accessed into the WiFi network before configuring.
7
8.3 Power on the camera. Indicator will flash RED and GREEN light alternately slowly
(1 second/once). Use a sharp tool to press and hold the SET button for more than 2
seconds until the indicator RED and GREEN light alternately quickly (0.5 second/once)
and then release.
8.4 Login into the app and then click “+” to add a new WiFi camera. The APP will find
the camera automatically.
8.5 Click the device and it will jump to the WiFi configuring interface. And then you can
re-name the camera if you want. Then input the WiFi name& password and then click
“Start binding device..”. And then the phone will jump to the WLAN network connecting
interface. Find the “SmartDoorV2-XXXXX” WLAN network (XXXXX is the device ID, it
should be correspondence with the ID labeled on the cover of the camera) and connect
it to send the configuring parameters to the camera.
8
8.6 Click “BACK”function button of the phone to return to the “LinkCraft”APP once the
WLAN network switch back to the WiFi network which you intend to use for the camera.
And the APP will display a dialog box of “Binding is successful”.
9
8.7 Click “OK”to jump to the camera display interface after the binding is successful.
After waiting for a few seconds, the “online”status will turn to “Connected”which
indicates that the camera is properly connected to the network. You can’t touch the
device to get into the main control interface until the status turns to “Connected”.
10
9. How to Add the Camera to the iOS Phone
9.1 Register a user account and login into the APP refer to step 7.1 and ensure your
phone has been connected to a valid WiFi network similar as step 7.2.
9.2 Power on the camera. Indicator will flash RED and GREEN light alternately slowly
(1 second/once). Use a sharp tool to press and hold the SET button for more than 2
seconds until the indicator RED and GREEN light alternately quickly (0.5 second/once)
and then release.
9.3 Login into the app and then click “+” to add a new WiFi camera. The APP will notify
you to jump to the WiFi setting to connect the WiFi of the camera.
9.4 Jump to the Wi-Fi settings according to the notification. Find the WiFi name of
Smart Door-xxx and then connect it. Go back to the APP after connecting successfully.
And then you can input the WiFi password for the camera. Click binding device to
confirm. The APP will pop up a binding success dialog and also the camera will display
Andere Topens Sicherheitskamera Handbücher
